ARMY MIL-M-14745 (1)-1972 MINOL-2 COMPOSITION《MINOL-2合成物》.pdf

上传人:proposalcash356 文档编号:445695 上传时间:2018-11-16 格式:PDF 页数:3 大小:120.43KB
下载 相关 举报
ARMY MIL-M-14745 (1)-1972 MINOL-2 COMPOSITION《MINOL-2合成物》.pdf_第1页
第1页 / 共3页
ARMY MIL-M-14745 (1)-1972 MINOL-2 COMPOSITION《MINOL-2合成物》.pdf_第2页
第2页 / 共3页
ARMY MIL-M-14745 (1)-1972 MINOL-2 COMPOSITION《MINOL-2合成物》.pdf_第3页
第3页 / 共3页
亲,该文档总共3页,全部预览完了,如果喜欢就下载吧!
资源描述

1、MIL-bl4745 (MU) -1 15 JUNE 1972 This Aniendment form a part of Military Specification MLM-14745 (MU), dated i5 April 1968. Paragraph 2.1: Delete iiPURC-IASE XSCRIF11WS PA-PD-3087 - Amnium Nitrate Grained (For Use In Explosives)“, and substitute “MIL-A-50460 - Annnium Nitrate, Prilled (For Use In Amn

2、unition) .I1 Paragraph 3.1.1: Delete in its entirety an substitute the following: “3.1.1 Amnonium Nitrate.-The amnoniun nitrate shall comply with the requirements of Military Specification MILA-50460 (M). of the ambnium nitrate shall not exceed 0.15 percent when tested as specified in 4.2.2.11 The m

3、oisture Paragraph 3.2 - Conposition, Table I: Delete the following: “Percent 40 t 3 . 20T2 40 3 - And substitute: “Percent 40 + 3 20 T 3 40 3 II - Pat.agrah 3.5 : biete in its entirety, FSC: i376 f Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-

4、M-14745 (1) 13 P 7977906 027b487 3 W T Paragraph 4.2.3, Sampling for Test: Delete the following: “Samples from kettle from each line“ and substitute: “The samples shall be taken from the discharge, spout (leg) of the min pouring kettle irmiediately before entering the bms at each line and shift.“ Pa

5、ragraph 4.3.1: Delete in its entirety and substitute the following: “4.3 , 1 Determination of charge composition. -The specimen shall be taken from a sample approximately four (4) inches in diameter with a maximum thickness of one-quarter (U41 inch that has been ground to pass a number 10 mesh sieve

6、, All weighing shall be done on an analytical balance to plus or miYius 0.0002 gram. The specimen selected from the ground sample shall be approximately 2 grams, accurately weighed, and shall be placed in a tamd, medum-porosity, sintered glass crucible. A stirring rod and about 20 ml of benzene shal

7、l be added to the crucible and the contents shall be stirred three times for about 30 seconds each time. The crucible and contents shall be placed on a filtration apparatus and suction applied to draw out the benzene solution. With the solution still on, the walls of the crucible and the stirring ro

8、d shall be washed down with additional benzene. The entire procedure, starting with the addition of 20 ml of benzene, shall be repeated two additional tims in order to insure complete extraction of the “i?. After the third extraction, remove the stirring rod after rinsing with benzene to insure that

9、 all adhering particles are washed into the crucible and continue the suction for about a minute after all the benzene solution has been drawn through. The crucible, which now contains mnium nitrate and aluminum, shall be placed in an oven at 100 degrees plus or minus 5 degrees C for approximately 1

10、5 minutes, cooled in a desiccator, and weighed. i After weimg the stirring rod shall be replaced in the crucible and about 20 m of distilled water.shaU be added. As before, the contents shall be stirred three times, for about 30 seconds each time, the solution shall be drawn through the crucible by

11、applying suction and the entire process repeated for a total of three extractions with 20 ml of water each time, After the third extraction, the stirring rod shall be washed with water and remved, as before, but the final water wash shall be followed by an acetone rinse in order to displace the wate

12、r and facilitate drying. shall be aspirated for about a minute before transferring to the oven. oncible, which now contains only aluminum, shall be dried for approximately i5 minutes at 100 degrees plus or minus 5 degrees C, cooled in a desiccator, and weighed. The composition shall be calculated as

13、 follows: After the acetone rinse, the crucible The 0,Ol w Amnonium Nitrate “4 NO3 % = W2 - W3 -mn? 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Al*m% = w3 - wo o. 01w W = Weight of Specimen; gram Wo= Weight of enpty crucible, gram W = Weight of

14、 cnioible, “4 NO3 and Al, $= Weight of crucible and Al, gram wi= w + wo, gram c“IDIAN: ARMY-Mu PHEPARING A(XWITY: ARMY-Mu PJ5WEXX NUMBER: 1376-A-O12 *U. S GOVERNMENT PRINTING OFFICE: 1972 -714-538/1666 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

展开阅读全文
相关资源
猜你喜欢
  • BS PD IEC TS 62763-2013_5284 Pilot function through a control pilot circuit using PWM (pulse width modulation) and a control pilot wire《通过控制导向线使用PWM (脉冲宽度调制) 的导向功能和控制导向线》.pdf BS PD IEC TS 62763-2013_5284 Pilot function through a control pilot circuit using PWM (pulse width modulation) and a control pilot wire《通过控制导向线使用PWM (脉冲宽度调制) 的导向功能和控制导向线》.pdf
  • BS ISO 8070-2007 Milk and milk products - Determination of calcium sodium potassium and magnesium contents - Atomic absorption spectrometric method《牛奶和奶制品 钙、钠、钾和镁含量的测定 原子吸.pdf BS ISO 8070-2007 Milk and milk products - Determination of calcium sodium potassium and magnesium contents - Atomic absorption spectrometric method《牛奶和奶制品 钙、钠、钾和镁含量的测定 原子吸.pdf
  • BS ISO 8082-1-2009 Self-propelled machinery for forestry - Laboratory tests and performance requirements for roll-over protective structures - General machines《林业用自推进机械 防倾.pdf BS ISO 8082-1-2009 Self-propelled machinery for forestry - Laboratory tests and performance requirements for roll-over protective structures - General machines《林业用自推进机械 防倾.pdf
  • BS ISO 8082-2-2011 Self-propelled machinery for forestry Laboratory tests and performance requirements for roll-over protective structures Machines having a rotating platf.pdf BS ISO 8082-2-2011 Self-propelled machinery for forestry Laboratory tests and performance requirements for roll-over protective structures Machines having a rotating platf.pdf
  • BS ISO 8083-2006 Machinery for forestry - Falling-object protective structures (FOPS) - Laboratory tests and performance requirements《林业机械 落体防护装置(FOPS) 实验室试验和性能要求》.pdf BS ISO 8083-2006 Machinery for forestry - Falling-object protective structures (FOPS) - Laboratory tests and performance requirements《林业机械 落体防护装置(FOPS) 实验室试验和性能要求》.pdf
  • BS ISO 8086-2004 Dairy plant - Hygiene conditions - General guidance on inspection and sampling procedures《乳品厂 卫生条件 检验和取样程序通用指南》.pdf BS ISO 8086-2004 Dairy plant - Hygiene conditions - General guidance on inspection and sampling procedures《乳品厂 卫生条件 检验和取样程序通用指南》.pdf
  • BS ISO 8096-2005 Rubber- or plastics-coated fabrics for water resistant clothing - Specification《雨衣用橡胶或塑料涂覆织物 规范》.pdf BS ISO 8096-2005 Rubber- or plastics-coated fabrics for water resistant clothing - Specification《雨衣用橡胶或塑料涂覆织物 规范》.pdf
  • BS ISO 8097-2001 Aircraft Minimum airworthiness requirements and test conditions for certified air cargo unit load devices《航空器 经认证的航空货运集装单元装置最低适航性要求和试验条件》.pdf BS ISO 8097-2001 Aircraft Minimum airworthiness requirements and test conditions for certified air cargo unit load devices《航空器 经认证的航空货运集装单元装置最低适航性要求和试验条件》.pdf
  • BS ISO 8114-1993 Textile machinery and accessories - Spindles for ring-spinning and doubling machines - List of equivalent terms《纺织机械和附件 环锭纺纱机和并线机用锭子 同义术语表》.pdf BS ISO 8114-1993 Textile machinery and accessories - Spindles for ring-spinning and doubling machines - List of equivalent terms《纺织机械和附件 环锭纺纱机和并线机用锭子 同义术语表》.pdf
  • 相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > ARMY

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1