1、s- 37- e! MIL-M-48629 (AR) - s- a O 3 October I985 SUPERSEDING MIL-M-63380 (AR) 28 September 1979 MILITARY SPECIFICATION MINE, ANTITANK, PRACTICE: M79 ASSEMBLING AND PACKING This Specification is approved for use by the US Army Armament, Munitions and Chemical Command, and is available for use by al
2、l. Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification contains requirements not normally covered by the drawings, and provides quality assurance provisions for the fabrication of parts, assemblinq, and packing for one type of mine designated as Mine, Antita
3、nk, Practice: M79. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications and standards. Unless otherwise specified, the following specifications and standards of the issue listed in that issue of the Department of Defense Index of Specifications and Standards (DoDIS) specified in th
4、e solicitation, form a part of this specification to the extent specified herein. SPECIFICATIONS FEDERAL TT-C-490B - Cleaning Methods and Pretreatment of Ferrous Surfaces for Organic Coatings. MILITARY - MIL-A-48078 - Ammunition, Standard Quality Asssurance Provisions, General Specification For. Ben
5、eficid comments (recommendatim, rbditians, deletions) and any pertinent dita rhidr may be of use in improving this document 8hould.k addressed tbr Commrndar, W Army Armament Research Md Development Canta, Attnr AMSMC-QA, Dover, NOW distribution Is unlimited . THIS DOCUMENT CONTAINS / PAGES - Provide
6、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-M-48629 (AR) STANDARDS MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspections By Attributes. 2.1.2 Other Government documents, drawinqs, and publications. and publications form a part of thi
7、s specification to the extent specified herein. DRAWINGS The following other Government documents, drawings, t US ARMY ARMAMENT RESEARCH AND DEVELOPMENT CENTER Ub 1 9243805 - Pkg Mine, AP: HE, M74 or Mine, AT, Practice: M79 in Container, Ammo, Plastics: PA-83. PA-83, for Mine, AP: HE, M74 or Mine, A
8、T, Practice: M79. r 9317994 - Mine, Antitank, Practice: M79. 9333791 - Pkg for Plastic Ammunition Container: US ARMY MATERIAL DEVELOPMEMT AND READINESS COMMAND 19-48-4116/95M-20PA 1002 - Unitization Procedures for Boxed Ammunition and Components on 4-WAY ENTRY PALLETS . (Copies of specifications, st
9、andards, drawings, and publications required by manufacturers in connection with specification procurement functions should be obtained from the procuring office or as directed by the contracting officer.) 2,1.3 Other publications. The following documents forms a part of this specification to the ex
10、tent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted shall be those listed in the issue of the DODISS specified in the solicitation. Unless otherwise specified, the issues of documents not listed in th DODISS shall be the issue of the nongovernment doc
11、uments which is current on the date of the solicitation . O 2 r 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-a O a MIL-M-48629 (AR) AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM-D-3951 - Commercial Packaging. (Application for copies of
12、ASTM publications should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, Pennsylvania 19103) 2.2 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein, the text of this specification shal
13、l take precedence. 3. REQUIREMENTS 3.1 Materials. Materials shall be in accordance with the applicable drawings, specifications and standards. 3.2 Assembly. The assembly shall comply with all requirements specified on Drawing (Dwg.) 9317994 and all associated drawings and with all requirements speci
14、fied in applicable specifications and standards. 3.3 Forty-foot drop test. The practice mine shall show-no evidence of broken, cracked, or loose parts which will render it unusable, after being dropped from a height of forty (40) feet (ft) as specified on Dwg. 9317994 and in 4.5.1. 3.3.1. Paint adhe
15、sion test. The painted practice mine tested 3.3.2. Salt spray test. The painted practice mine tested as in 4.5.2 shall show no removal of the coating by the adhesive tape. in 4.5.3 and examined immediately after removal from the salt spray test shall show no more than a trace of rusting (No. 9-1 Met
16、hod 6451 of FED-STD-141) and no more than five scattered blisters none larger than 1 mm in diameter. On removal of the paint there shall be no more than a trace of rusting, pitting,or corrosion of the steel. 3.4 First article inspection. This specification contains technical provisions for First Art
17、icle Inspection. Requirements for submission of First Article Samples by the contractor shall be as specified in the contract. 3.5 Workmanship. All parts and assemblies shall be fabricated and assembled in a thorough, workmanlike manner, and all manufacturing, processing, and assembling operations s
18、hall be correctly performed. All parts and assemblies shall be clean, free of burrs, sharp edges, cracks, dirt, grease, rust and other foreign matter that may impair proper functioning. The cleaning 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1
19、3 777770b 0322507 5 I MIL-M- 4 86 2 9 (AR) method used shall not be injurious to any parts, nor shall the parts be contaminated by the cleaning agents. Exterior surface coatings shall be continuous; however a few light scratches not exposing base material mpy be permitted. All required markings and
20、stampings shall be neat and sharply defined. Required packing shall be dry. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection and standard quality assurance provisions. Unless otherwise specified herein or in the contract, the provisions of MIL-A-48078 shall apply and are hereby made
21、 a part of this detail specification. 4.2 Classification of inspections. The following types of inspection shall be conducted on this item. a. First article inspection (see 4.3). b. Quality conformance inspection (see 4.4) . 4.3 First article inspection. 4.3.1 Submission. The contractor shall. submi
22、t a first artic1e;sWple as designated by the contracting officer for evaluation in accordance with provisions of 4.3.2. The first article sample shall consist of the following items in the quantities as indicated. PART DES CRI PT I ON DRAWINGS QUANT IT Y Mine, Antitank, Practice: M79 9317994 15 4.3.
23、2 Inspections to be performed. See MIL-A-48078 and 4.3.3 Rejection. See MIL-A-48078. Table I as specified herein. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-.FI I .FI al d u *FI U LI m U 111 bl .FI Eb( H w d PI . 2 w U 5 Provided by IHSNot for
24、 ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-M-48629 (AR) 4.4 Quality conformance inspection. .- 4.4.1 Inspection lot formations. Inspection lots shall 4.4.2 Examination. (See MIL-A-48078). Unless otherwise comply with the lot formation provisions of MIL-A-48078. s
25、pecified in the Classification of Defects and Test Tables, sampling plans and procedures for major and minor defects shall be in accordance with MIL-STD-105. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-a ? =I -1 5 rl QI 4 c III c Y 3 8 8 O pi 7
26、 . n 2 n d I 2 I 3 3 r: u 2 al u m U & O u u m c ai Q i -I m C III c, O d ci u ai n al LI U ri 3 P c FI -I a VI 5 r i - a - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-8 rl ti H ri IL 4. N N e di e e 0 I VIL-M-48b27 13 W 7979906 0322511 7 W CJ Nc
27、v VI e *e e dp dpdp dfJ o O0 In e we W o O0 O e ea e a 4 c u) 2 E Y LI 8 O pi n r. O a F E f O IL n n u 4 L3 c3 ai LL n n O h Ln E O LL O Z 4 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-z O H b u w pi VI E w u .i Fri z O u N I4 4 3 0 H I I I I
28、I I I I I I I I. cl t !?i XI I ! MIL-M-4b27 33 7777906 0322532 7 - drlrlrl mmmm 5555 3333 mu)(IIu) .li .d -4 .d ri 4 m 7 u) .4 3 2- u) -4 3 rl (4. 5 u) -4 3 (v(v(v(v CVN (v (v (v CVN“ N rn mmmm mm m m m mmmm m- m e- *o e o eoee o e . - - Ooir e* e e eeee O rlooo O0 o o o O000 4 o u al c -4 w al u al
29、 c O z pi c E X Li O 3 4 : 8 O PI :I u 9 Y i- - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-RIL-R-qBb29 33 m 777770b 0322533 O W MIL-M-48629 (AR) 4.4.3 Testinq. Testing is described in the First Article and Quality Conformance Inspection Tables.
30、4.4.4 Inspection equipment. The inspection equipment required to perform the examinations and tests prescribed herein is described in the “Paragraph Reference/Inspection Method“ column in the tables starting with paragraph 4.4.2.1. The contractor shall submit for approval inspection equipment design
31、s in accordance with, the terms of the contract. See Section 6 of MIL-A-48078 and 6. herein. O 4.5 Methods of inspection. 4.5.1 Forty-foot drop test. A sample of eight (8) practice mines shall be randomly selected and subjected to the forty-foot drop test. Orientation of each end, for the ten drops
32、per end (20 drops total), shall be random. The angle of mine at impact shall be approximately 45O and the drop shall be made onto a 1 inch o steel plate. Observation shall be made for compliance with Dwg. 9317994 and the requirement of 3.3, 4.5.2 Paint adhesion test. This test shall be performed as
33、specified in TT-C-490B. 4.5.3 Salt spray test. This test shall be performed as 5. PACKAGING 5.1 Preservation and packaginq. 5.1.1 Level A. The mines shall be preserved and packaged in 5.2 Packinq. 5.2.1 Level A. Packing shall be in accordance with Dwg. 5.3 Marking. 5.3.1 Level A. Marking shall be in
34、 accordance with Dwgs. 9333791 and 9243805. specified in TT-C-490B. accordance with Dwg. 9333791. 9243805. 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-M-48623 13 373770b 032251q 2 I - 5.4 Unitization. 5.4.1 Level A. Unitization of mines as
35、 packed in 5.2.1 shall be in accordance with Dwg. 19-48-4116/95M-20PAlO02 (DARCOM Ammo Center). O 6. NOTES 6.1 Intended use. The Mine, Antitank, Practice: M79 is intended to be used to simulate the M74 and M75 Mines in loading and launching drills rom the M128 Mine Dispenser. 6.2 Orderinq data. See
36、MIL-A-48078. 6.3 Submission of inspection equipment design for approvals. (See MIL-A-48078.) Submit equipment designs as required to Commander, US Army Armament Research and Development Center, ATTN: AMSMC-QAT-I(D), Dover, New Jersey 07801-5001. 6.4 Distribution of ammunition data cards, inspectHn a
37、nd test results. Distribution of data cards, inspection, and test results shall. include the following: Commander, US Army Armament Research and Development Center, ATTN: AMSMC-QAT-M(D), Dover, New Jersey 07801-5001. 6.5 Drawings. Drawings listed in Section 2 of this specification under the heading
38、US Army Armament Research and Development Center (ARDC) may also include drawings prepared by, and identified as Edgewood Arsenal, Frankford Arsenal, Rock Island Arsenal, ARRADCOM, or Picatinny Arsenal drawings. Technical data originally prepared by these activities is now under the cognizance of ARDC . Custodian: Army-AR Preparing activity: Army-AR (Project 1345-A337) 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
