1、MIL-W52372B MIL-M-5 2 37 2A 30 October 1973 MILITARY SPECIFICATION MEASURES, DRY CHEMICAL, WATER PURIFICATION This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers measures for use in military designed water
2、 purification equipment sets. 2. APPLICABLE DOCUMENTS 2.1 Issues of documents. The following documents of the issue in effect on date of invitation for bids or request for proposal form a part of this specification to the extent specified herein: SPECIFICATIONS FEDERAL L-P-1035 - Plastic Molding Mat
3、erial, Vinyl Chloride Polymer and Vinyl Chloride - Vinyl Acetate Copolymer , Rigid. FSC 4610 I Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: US Army Mobility Equipment Research and Development
4、 Command, ATTN: DRDME-DS, Fort Belvoir, VA 22060 by using the self- addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. THIS DOCUMENT CONTAINS I PAGES. Licensed by Information Handling Servicesl4lL-I-i-5 237 2B QQ-C-783. PPP-B-60
5、1 PPP-B-636 - Strapping, Steel, and Seals. - Boxes, Wood, Cleated-Plywood. - Boxes, Shipping, Fiberboard. STANDARDS 14 LLITARY MTL-STD-129 MIL-CTD-150 li IL-STD-118 8 - Sampling Procedures and Tables For Inspection by At tribu tes. - Marking For Shipment and Storage. - Identification Marking of US -
6、 Commercial Packaging of Supplies Military Property. and Equipment. (Copies of specifications and standards required by contractors in connaetton wlth specifh procurement functfons should be obtained from the procuring activity or as directed by the contracting officer.) 2.2 Other publicatit. The fo
7、llowing documents form a part of this specifcatisn toKatent specified herein. the issue in efect on date of invitation for bids or request for pro- posal. shall apply. Unless otherwise indicated, ATIERlGAN NATIONAL STANDARDS INSTTUTE (ANSI) Y14 . 5 .-i Dimensioning and Tolerancing For Englneering Dr
8、awings, (Application for coptes should be addressed to the American National Standards Institute, nc., 1430 Broadway, New York, NY 100lG.) AIIERIGAN SOCIETY POR TESTING AND MATERIALS CASTM) B 209 B 218 13 221 - Aluminum-Alloy Sheet and Plate. - Aluminum-Alloy Drawn Seamless - Aluminum-Alloy Extruded
9、 Bars, Tubes Rods, Wire, Shapes, and Tubes. (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) 2 Licensed by Information Handling ServicesMIL-M-52372B qb W 77777Ob 0239433 7 m MIL-M-52372B (Technical society and t
10、echnical association specifications and stand- ards are generally available for reference from libraries. They are also distributed among technical groups and using Federal agencies.) 3. REQUIREMENTS 3.1 Description. Measures shall be as shown on Figures 1 through 6 and as specified herein. 3.2 Mate
11、rial. Material and design shall be as shown on Figures 1 through 6, as specified (see 6.2), and as specified herein. Mat,erials not specified shall be selected by the contractor and shall be subject to all provisions of this spec if ica tion (see 6.3) . 8 3.3 Identification marking. In addition to m
12、arkings specified on the applicable figure, the measure shall be identified in accordance with MIL-STD-130. 3.4 Workmanship. All parts of the measures that are molded, formed or stamped, shall be clean and free from dirt, fins, cracks, pinholes, slivers, pits and other extraneous material that may i
13、mpair the ser- viceability of the measures. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection, Unless otherwise specified in the contract, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contra
14、ct, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements. specified herein, unless disapproved by the Government. The Cdvernment reserves the right to perform any of the inspections cet forth in the specification where such inspections ar
15、e deemed necessary to assure supplies and services conform to prescribed requirements. 4.2 Classification of inspection. Inspection requirements specified herein are classified as follows: (a) (b) Inspection of packaging (4.5). Quality conformance inspection (see 4.3). 3 Licensed by Information Hand
16、ling ServicesMEL-l-5237 2B 4.3 Quality conformance inspection. 4,3.l. Samplin 7. ITEM MAY BE MULTI PIECE CONSTRUCflON. MMENSIQNING AND TCKERANCING, SEE ANSI Y14.5 UOY 3003-0, OR 5052-0. FIGURE 2, Measure filter aid, 46 CU. in. 8 Licensed by Information Handling ServicesMIL-bl-52 3726 u) W c O 2 Y Li M O E 10 Licensed by Information Handling ServicesIG I O 0180-COZ-00-0196 NSN i I I -t- -“I Licensed by Information Handling Services6J fiU.8. GOVERNMENT PRINTING OFFICE: 1980 - 603.121/3747 12 Licensed by Information Handling Services
