1、flIL-P-14b3YA 83 7777706 0378880 T m _ MIL-P-14634A 30 June 1974 SUPERSEDING MIL-P-14634 28 Aug 1967 MILITARY SPEGIFICATION PANEL MARKER RED CROSS, 4 FEET BY 4 FEET This specification is approved for use by.all Departments and Agencies of the Department of Defens. 1. SCOPE 1.1 Scope,- This specifica
2、tion covers one type and size of red cross panel marker used by the Department of Defense. 2. APPLICABLE DOCUMENTS 2.1 The following documents of the issue in effect on the date of invitation for bids or request for proposal form a part of this specification to the extent specified herein. SPEC IF I
3、CA TIONS FEDERAL V-T-205 - Thread, Polyester PPP-B-601 - Boxes, Wood, Cleated-Plywood PPP-B-621 - Boxes, Wood, Nailed and Lock-Corner PPP-B-636 - Box, Shipping, Fiberboard PPP-B-676 - Boxes, Set-up MIL-C-43256 - Cord, Polyester, Solid Braid MILITARY STANDARDS - FEDEBAL FED-STD-191 - Textile; Test Me
4、thods FED-STD-751 - Stitch, Seam and Stitching MIL-STD-105 - Sampling Procedures and Tables for MIL-STD:129 - Marking for Shipment and Storage MILITAR Y Inspection by Attributes DRAWINGS THE INSTITUTE WS HERALDRY 5-1-357 - Panel. Marker, Red Cross, 4 by 4 /FSG 8345/ 1 - THIS DOCUMENT CONTAINS tight,
5、 resulting in excessive tightness of fabric on seams. One stitch less than the minimum specified inch Two or more stitches less than the minimum spec- ified One stitch in excess of maximum specified. e o I Two or more stitches in excess of maximum spec- ified,. gins; gage on 1/16 inch,“. double need
6、le stitching Stitches per Stitching mar- Under or over specified width by more than 6 ita t ion Minor X - - X X X - X - X Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P- 14634A Examine Defect hread breaks Overstitched less than 1-1/2 inches on
7、 stitch type 401; backstitched less than 1 inch on stitch type 301 NOTE: Thread breaks not backstitched or not over- stitched shall be classified as open seams. titching ends Not backstitched (except where ends are held down by other stitching or turned under in a hem). Any required component, any r
8、equired operation omitted or not as specified (except as other- wise specified herein): omponents and a s sembl y -seriously affecting serviceability. -affecting serviceability, but not seriously. e Needle chews expected to develop into a hole Seam badly pleated or puckered It itching One or more re
9、quired rows of stitching omitted abric Holes (except punched holes), cut or tear. Exposed punched hole, i.e., not covered by at- tached parts . Color of base cloth not as speci Color of base cloth off shade. Fabric defects: -ser i ous ly affecting serviceab -affecting serviceability, but . ied . lit
10、y, not seriously. o serve intended purpose, Finished length less than specified by more than one inch Tie cord attached to face of panel marker. ing serviceability . ability, but no seriously . -seriously affecting serviceability . ie cord Edges frayed or scalloped; misplaced failing to ryelet Broke
11、n, cracked or malformed; seriously affect- Broken, cracked or malformed; affecting service- Size or type not as specified: -affecting serviceability, but not seriously. a Missing . Clinched excessively tight, cutting fabric or insecurely clinched,. 7 Provided by IHSNot for ResaleNo reproduction or n
12、etworking permitted without license from IHS-,-,-Examine Defect Pins Not aluminum., Bent, broken, malformed or otherwise defective, affecting serviceability . Point blunted, Not correct size. . Not attached to cord with slip knot., stitchin -more than 1/2 inch, but not more than 1 inch, -more than 1
13、 inch, Seams and Open seam on stitch type 301: Any open seam on stitch type 401, except run- offs : -3/4 inch or more.,.,. -more than 1/4 inch but less than 3/4 inch., -more than 1/2 inch, but not more than 1 inch, -more than 1 inch. Chain portion of 401 stitch type appears on fact side.,.,. NOTE: A
14、 seam shall be classified as open when one Run-Offs on stitch type 401: or more Stitches joining a seam are broken or when two or more consecutive skipped stitches or run-Offs occur. On double stitched seams, a seam shall be considered open when either one or both sides of the seam are open. Hems Tw
15、isted or pleated Hem une ven.,.,? Hem on wrong side of panel marker. pee os y e *. o *. I Constructed with a single turn under when a double turn under is required. . Reinforcement Any reinforcement misplaced, failing to rein- patches force eyelet fully . Color of reinforcement patch not white Ma r
16、k i ng Ornitted, illegible, incorrect or misplaced Cleanness Noticeable grease or oil stains; thread ends not trimmed throughout . cation Minor X X X X X X - - X x - X X X X X X X X X 4.3.3.1.2 Dimensional defects.- Any dimension that is not within the specified tolerance shall be classified a defec
17、t. 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-P-ZLIb34A 83 m 777770b 0378888 4 m MIL-P-14634A 4.3.3.1.3 Inspection levels and acceptable quality levels (AQLs),- The inspection levels and the acceptable quality levels expressed in defects
18、per hunderd units shall be as follows: Inspection AQL level Major Total For defects applicable to 4.3.3.1.2 S-4 (one class) 2.5 4.3.4 Examination of preparation of delivery requirei2ent.s.- An examina- Defects shall be scored For defects applicable ta 4.3.3.1.1 II 4. Q 10. o tion shall be made to de
19、termine that packaging, packing and marking comply with the requirements of section 5 of this specification. in accordance with the list below. tainer fully prepared for delivery with the exception that it need not be sealed. defects of closure listed below. The lot size shall be the number of ship-
20、 ping containers in the end item inspection lot. S-2 and the acceptable quality level shall be 2,s. The sample unit shall be one shipping con- Shipping containers fully prepared far delivery shall be examined for The inspection level shall be Examine Defect and interior) sequence or method of applic
21、ation. serviceabiIity. closure of container flaps, inadequate stapling. Marking (exterior Omitted, incorrect, illegible, of improper size, location, Materials Any component missing, any componeiit damaged affecting Workmanship Inadequate application o components such as incomplete Contents Number pe
22、r container is more r less than required. 4.4 Tests.- Testing shall be in accordance with FED-STD-191. Fastness to weathering shall be tested in accordance with 5671. Fastenss to fresh water shall be in accordance with 5630. Fastness to salt water shall be tested in accordance with 5632. Fastness to
23、 crocking shall be tested in accordance with 5651 and fastness to light shall be tested in accordance with 5660 e 5, PREPARATION FOR DELIVERY 5.1 Packaging.- Packaging shall be level A or G, as specified (see 6.2). 5.1.1 Level A.- 5.1.1.1 Unit package. - One panel marker (with anchoring pins attache
24、d) shall be neatly folded and .placed in a snug-fitting transparent polyethelene bag approximately 6 inches wide and 10 inches deep. shall be aminimum of 0.004 inch thick. All seams and closures shall be effected by heat sealing. within the bag shall be expelled. The polyethelene film Prior to or du
25、ring the heat sealing operation excess air 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-Lq634A 3 = 9979906 0378889 b W MIL-P-14634A 5.1,1.2 Intermediate package.- Ten panel markers prepared as specified in 5.1.1.1, shall be-packaged in a s
26、nug-fitting paperboard box conforming to type I, variety 1, class A, style 4 of PPP-B-676. Box closure shall be in accordance with the appendix of the container specification. 5.1.2 Level C.- Panel markers shall be packaged to afford adequate 2r- tection against deterioration and damage during shipm
27、ent from the supply source to the first receiving station. The supplier may use his standard practice when it meets these requirements. 5.2 Packing.- Packing shall be level A, B or C, as specified (see 6.2). 5.2.1 Level A.- Panel markers, packaged as specified in 5.1, shall be packed in a snug-fitti
28、ng shipping container conforming to class 2, style 4 of PPP-B-621 or overseas type, style A, B, I or J of PPP-B-601. Box closure and reinforcing shall be in accordance with the appendix of the applicable con- tainer specification. 5.2.2 Level B.- Panel markers packaged as specified in 5.1.1, shall b
29、e packed in a snug-fitting fiberboard shipping container conforming to type CF or SF, class domestic, grade 275, style FOL of PPP-B-636. Closure shall be in accordance with the appendix of the container specification. The weight of contents in each container shall not exceed the size and weight limi
30、tations established by the container specification. 5,2.3 Level C.- Panel markers packaged as specified in 5,1, shall be packed in a manner to insure carrier acceptance and safe delivery at destination for the lowest transportation rates for such supplies, accordance with the rules and regulations o
31、f carriers applicable to the mode of transportation. Containers shall be in 5.3 Marking.- In addition to any special marking requirement in the con- tract or purchase order, unit packages, interior packages and shipping containers shall be marked in accordance with MIL-STD-129. 6. NOTES 4.1 Intended
32、 use,- Panel markers c,overed by this specification are in- tended to be used for ground to air identification of emergency helipads. 6.2 Ordering date.- Procurement documents should specify the following: (a Title, number and date of this specification. (h) When a standard sample will not be furnis
33、hed (see 3.1). 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-LLIb34A 83 = 7777706 0378870 2 m MIL-P-14634A (c) (d) When a first article is not required (see 3.2). Selection of applicable levels of packaging and packing (see 5.1 and 5.2). C
34、ustodians : Army - IH Air Force - 82 Navy - SA Review Activities: Air Force - 82 Navy - MC, SA Other - DP User Activities: Army - SM Project No. 8345-0080 11 I Preparing Activity: The Institute of Heraldry, United. States Army Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-i MIL-P-lq634A 83 79?77Ob 0378892 q B MIL-P-14634A 4 I P -. -t 12 * U. & GOVERNMENT PRINTING OFFCE: 1974-603-113/3635 -i F Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
