1、, . flIL-P-bO3LIOA 13 W 77777Ob 0337796 3 - MIL-P-60340A(EA) i4 February i978 SUPERSEDING MIL-P-60340 (MJ ) 6 May i965 MILITARY SPECIFICATION PROJECTILE, 155MM, SMOKE, HC, BE, 1162, PARTS FOR This specification is approved for use by US Army, Armament Research and Development Command, Department of
2、the Army and is available for use by all Departments and Agencies of the Depart- ment of Defense, 1. SCOPE 1-1 This specification covers the parts for the Prodectile, 155MM, Smoke, HC, BE, 1162. 2. APPLICABLE DOCUMENTS 2.1 Government documents. The following documents of the issue in ef- fect on dat
3、e of invitation for bids or request for proposal, form a part of this specification to the extent specified herein. SPECIFICATIONS MILITARY MIL-A-25C,O - Ammunition, General Specification For. FSC 1320 : Beneficial comments (recommendations, additions, deletions) and any : pertinent data which may b
4、e of use in improving this document should be: : addressed to: Commander, US Army Armament Research and Development : : Command, Attn: DRDAR-TSC-S, Aberdeen Proving Ground, EID 21010, by us-: : ing the self-addressed Standardization Document Improvement Proposal : : (DD Form 1426) appearing at the e
5、nd of this document or by letter. - THIS DOCUMENT CONTAINS IJ PAGES. 1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-P-60340A 13 m 773970b 0337747 5 m MIL-P-60 34 OA ( EA ) STANDARDS MIGSTD-105 - Sampling Procedures and Tables for Inspection b
6、y Attributes. MIL-STD-129 - Marking for Shipment and Storage. MIL-STD-1167 - Ammunition Data Card. MILISTD-1168 - Lot Numbering of Ammunition. MIL-STD-1188 - Commercial Packaging of Supplies and Equipment. DRAWINGS US ARMY ARMAMENT RESEARCH AND DEVELOPMENT COMMAND “CKFSIICAL SYSTEMS LABORATORY 88851
7、53 - Plate Baffle 8885154 - Spacer 888 515 5 - Spacer, Front 8885161 - Disc Closure B15-11-129 - Pin, Groove 9239112 - Spacer 9255386 - Expelling Charge Support (Copies of specifications, standards, drawings, and publications re- quired by contractors in connection with specific procurement function
8、s should be obtained from procuring activity or as directed by the Con- tractiilg Officer. ) 3.1 Materials and Parts. 3.1.1 Materials. All materials shall comply with the requirements as set forth in the applicable drawings and specifications. 3.1.2 - Parts. All parts shall conform to the requiremen
9、ts of the appli- cable drawings and specifications. All parts shall be dry, clean, and free of contamination (dirt, grease, oil, rust, or foreign matter) and damage, including but not limited to dents, cracks, chips, surface defects, tears, or deformation which could affect its assembly into the pro
10、jectile or its intended use. shall be free of burrs and sharp edges. 3.2 Workmanship. Parts *Formerly Edgewood Arsenal 2 .: Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2% MIL-P-603LtA 13 = 7777706 0337778 7 MIL-P-60340A( FA) 4. QUATJTY ASSURANCE
11、PROVISIONS 4.1 Responsibility for inspection. 4.1e1 Contractors responsibilities. Unless otherwise specified in the contract, the contractor i5 responsible for the performance of ail inspection requirements as specified herein, Except as otherwise specified in the con- tract, the contractor may use
12、his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. any of the inspections set forth in the specifications where such inspections are deemed necessary to assure supplies and services conform to specified
13、re- quirements. The provisions of NIL-A-2550 shall apply, The Government reserves the right to perform 4.1.2 Submission of moduct. At the time the completed lot of product is submitted to the Government for acceptance the contractor shall suoply the following information accompanied by a certificate
14、 which attests that the information sovided is correct and applicable to the product being submi t t ed (a) A statement %hat the lot complies with all of the quality assurance provisions specified within this specification. (b) Number of units of product inspected. (cl Results obtained, by defect co
15、de, for all inspection performed. i. (d) Drawing, specification number and date, together with an identification and date of changes. (e) Certificates of compliance on all material purchased by the contractor when such material is controlled by Government specifications referenced in any of the cont
16、ractual documents. (f) Number of items In the lot, (g) Ammunition data cards prepared in accordance with MIL-SID-1167 shall be supplied for each lot of like components. (h) Date submitted. Thecertificate shall be signed by a responsible agent of the certifying organization. The initial certificate s
17、ubmitted shall be substantiated by evidence of the agents authority to bind his principal. of the agents authority will not be required with subsequent certificates unless, during the course of the contract, this authority is vested in another agent of the certifying organization, Substantiation /.
18、3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-P-bO3LIOA 13 m 97777Ob 0337779 7 W MIL-P-60340A( EA) 4.1.3 Objective evidence. The contractor shall provide ob3ective evidence acceptable to the contracting officer that the requirements of Secti
19、ons 3 and 5 for which specific inspection has not been provided in this specification have been satisfied. 4.2 Quality conformance inspection. 4.2.1 Lotting. Each lot shall be identified and controlledin ac- cordance with MIL-sTD-. like sub-assemblies of one interfix number, produced by one manufact
20、urer, from the same materials and under essentially the same manufacturing con- dit ions. A lot shall consist of like components or 4.2.2 Sampling. 4.2.2,l For examination. Sampling shall be conducted in accordance The A o, A z o, k k O o fi .rl u) VI o, .o .rl c El rl .rl ggmaln UP- O00 00 li rl rl
21、.rlrl rlrl u P- al. M al pc Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-i- s PI 2 MIL-P-60340A 13 m 799770b 0337803 7 H al b 8 P . O k O a al c ;H a“ 8 al 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from
22、 IHS-,-,-NIL-P-603LIOA 13 M 9999906 O337804 9 W. al a 8 al v) * ? O 3 % ci al k o fi .d % s al k k O %4 +I O Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-c I NIL-P-bO3LtOA 13 7777706 0337805 O . 00000 3 d al a al Ei 8 O FI Provided by IHSNot for R
23、esaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-60340A 13 9939906 0337806 2 W t? k O t- B E w !i a V X m In Ln rl E E-c. Q u L Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-a - _- MIL-P-60340A 13 7799906 0337807 4 M
24、6, NiES 6.1 Intended use. Smoke Projectile, BE, I These components are intended for use in the 155MM 1162. Procurement documents shoed specify the title, 6.2 Ordering data. number, and date of this specification. Custodian: Am - FA Preparing activity: Army - EA ProJect Mo. 1320-A406 f7LJ.S. GOVERNMENT PRINTING OFFICE: 1978 -703-122/1481 12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
