1、CI- MIL-P-64005 13 m 7997906 0352825 4 m Approved for public release; distribution is unlimited . THIS DOCUMENT CONTAINS PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-bLIOOS 13 W 7449706 O352826 h li MIL-P-64005 (AR) 2.1.2 Other Govern
2、ment documents, drawinqs and publications. The following other Government documents, drawings and publications form a part of this specification to the extent specified herein. DRAWINGS US ARMY ARMAMENT RESEARCH AND DEVELOPMENT CENTER (ARDC) PRODUCT AND PACKAGING DRAWINGS 11751156 - Projectile, 155M
3、M, GB2, M687 Ogive 9357729 - Projectile, 155ME9, GB2, M687 Marking 9349367 - Projectile, 155MM, GB2, M687, Metal Diagram Parts Assembly with Loaded Ogive US ARMY CHEMICAL RESEARCH AND DEVELOPMENT CENTER (CRDC) PRODUCT AND PACKAGING DRAWINGS E15-12-321 -Pallet, Side Loading for 155MM, M687 Projectile
4、 (Copies of specifications, standards, handbooks, drawings, and publications required by manufacturers in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting officer). 2.1.3 Order of precedence. In the event of a conflict
5、between the text of this specification and the references cited herein, the text of this specification shall take precedence. 3. REQUIREMENTS 3.1 Materials. Materials and parts shall be in accordance 3.2 Loaded ogive. The loaded ogive shall comply with all the with applicable drawings and specificat
6、ions. requirements specified on dwg. 9349367 and meet the requirements specified in applicable specifications. 3.3 Clean explosive scrap. Clean explosive scrap resulting from normal production operations may be re-melted and used provided that it complies with the requirements for high explosive (in
7、cluding grade) as specified on dwg. 9349367 with the exception that it does not have to meet the material form requirement called for in MIL-0-60371. Scraps from the floor, ventilation and suction apparatus (other than from machining operations specifically controlled to prevent contamination of exp
8、losive) shall not be used (see 6.8) . 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-64005 13 m 7797706 0352827 8 m MIL-P-64005 (AR) 3.4 Cavitation in high explosive charqe. 3.4.1 General. Cracks and cavities within an explosive e charge sha
9、ll not exceed the requirements specified in Table I when determined as specified in 4.5.1. Cavities having a maximum (max) projected length of 1/16 inch shall be disregarded provided that they are separated by 1/2 inch or more of solid explosivel. TABLE I. Cavitation requirements Sum of projected ar
10、eas of the cavities, 1/4 NA excluding pipes, cracks and annular %: rings, square inch (sq. in.). P t Projected length of any cavity, excluding 1/2 1/2 NA pipes, cracks, and annular rings (in.). Piping cavities, maximum (max.) projected 1/8 1/4 NA area (sq. in.). Piping cavities, max. projected width
11、 (in.) 1/8 1/4 NA Citacks, max. projected width (in.). 1/32 1/32 NA Annular rings, max. projected width (in.) . O 1/16 NA (Segments, See Figure 1) Piping cavitation is defined as cavitation located on or near the vertical center line of the ogive with the longitudinal axis (length) at least three ti
12、mes or greater than the width. An annular ring is defined as cavitation that takes the form of a ring or portion thereof around the periphery of the cast. * Void permitted in Segment C. 3.4.2 Cracked charges. There shall be no more than three transverse cracks in any total charge, and not more than
13、one traverse crack shall be permitted in Segment A. 3.4.3 Porosity. Porous areas shall be treated as cavities and shall be subject to the restrictions placed upon cavities, except that 80 percent of the projected length and 80 percent of the projected area shall be considered for acceptance purposes
14、. 3 - . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-69005 13 a 7779706 0352828 T II MIL-P-64005 (AR) 3.4.4 Base separation. The maximum allowable base separation between the base of the ogive cavity and the cast shall be .O15 of an inch whe
15、n determined in accordance with 4.5.3. 3.4.5 Surface cavitation. Voids or cracks in segment C of Figure 1 shall not be cause for rejection. Cavities in the base of the fuzewell (top of segment B) shall not be cause for rejection provided the sum of the areas of the cavities is not greater than 80 pe
16、rcent of the top of segment B. No point may extend above the flat surface on which the liner will rest. Cavities having a maximum dimension of 1/32 inch.or less shall be disregarded in surface cavitation computations. 3.5 Loading of high explosive. 4 B 3.5.1 Loading. The ogive shall be loaded in acc
17、ordance with dwg. 9349367. -i 3.5.2 Mating surfaces. The mating surfaces of threads shall be free of caked explosives and all threads shall be free of foreign material. If a chemical cleaner is required, acetone or methylene chloride shall be used. Care shall be taken to prevent the chemical cleaner
18、 from coming into contact with the charge and becoming entrapped in the ogive. 3.5.3 Solid explosives. Solid explosives shall not be in the ogive before loading or added to the ogive during initial pouring or cooling. ogive prior to loading shall be free from foreign matter. 3.5.4 Ogive interior cav
19、ity. The interior cavity of the 3.5.5 Fuze well. The fuze well including threads shall be free from any foreign matter or loose explosive prior to assembly of the liner. 3.5.6 Exterior surfaces. There shall be no explosive on any exterior ,surfaces of the projectile after loading. 3.5.7 Ogive cavity
20、. The ogive cavity shall be free of scales, fins, burrs, draw marks, laminations, embedded foreign matter, folds, pits and sharp edges. 3.6 Liftinq plug. The projectile metal parts assembly with loaded ogive and with lifting plug assembled shall meet the disassembly torques specified n dwg. 9349367.
21、 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-b4005 13 W 777770b 0352827 1 W MIL-P-64005 (AR) 3.7 Provinq qround. 3.7.1 Metal parts assembly with inert ogive“. There shall be 0 no evidence of metal parts failure when tested at excess press
22、ure. Metal parts failure shall be: a. Loss or breakup of metal part components in bore or in b. Shear of the rotating band as evidenced by complete * Applicable only when ballistic test is used to qualify both flight (except obturator). lack of engraving. metal parts and ogive loading. * a T 3.7.2 M
23、etal parts assembly with loaded oqive. -.There shall be no evidence of metal parts assembly with loaded ogive failure when tested for excess pressure or at zone 3. Failure of this configuration shall be: a. Premature burst of the oxamide explosive composition in b. Partial or incomplete functioning
24、upon impact. c. Any metal parts separation in bore or in flight. bore or in flight. 3.8 First article inspection. This specification contains technical provisions for first article inspection. Requirements for the submission of first article samples by the contractor shall be as specified in the con
25、tract. 3.9 Workmanship. :The requirements of workmanship are as specified on the applicable drawings, reference specifications and the following: 0 3.9.1 Cleaninq. If required,-the cleaning method shall not be injurious to any of the part(s) nor shall the parts be contaminated by the cleaning agent
26、. 3.9.2 Protection of the rotatinq band. Care shall be exercised at all times so that the rotatina band of each d - -. - projectile will not be nicked or burred. 3.9.3 Foreiqn matter. No part or assembly shall contain dirt, grease, chips, oil, rust corrosion or other foreign matter prior to inspecti
27、on and shipping. 3.9.4 Obturator. Care shall be. taken at all- times to protect obturator from being damaged. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-bqOO5 13 9?79?7906 0352830 9? .MIL-P-64005 (AR) 4 . QUALITY ASSURANCE PROVISIONS 4.1
28、 Responsibility for inspection and standard quality e assurance provisions. Unless otherwise specified herein or in the contract, the provisions of MIL-A-48078 shall apply and are hereby made a part of this detail specification. 4.2 Classification of inspections. The following types of inspections s
29、hall be performed on this item: a. First Article Inspection b. Quality Conformance Inspection 4.3 First article inspection. 4.3.1 Submission. The contractor shall submit a first article sample as designated by the Contracting Officer for evaluation in accordance with the provisions of 4.3.2. The fir
30、st article sample shall consist of the following items in sample quantities as indicated. Part Desc r i pt io n Drawinq Quant i ty Projectile Metal Parts Assembly 9349367 complete with Base-Adapter and Loaded Ogives Loaded Ogives 9349367 20 8 4.3.2 Inspections to be performed. See MIL-A-48078 and Ta
31、ble II specified herein. 4.3.3 Rejection. See MIL-A-48078. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-,“I o . H H w MIL-P-bLI005 33 7779706 0352833 T W g -4 tn O a al a a O GI c u 3 3.i rl a m rn .rl E 4 m u LI a pi d a u c N m -P . - I ce woo
32、 . c) -4 a -P ww mm . . CVN N r-b m mm . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-b4005 13 W 777770b 0352832.1 W MIL-P-64005 (AR) 4.4 Quality conformance inspection. 4.4.1 Inspection lot formation. Inspection lots shall comply with the l
33、ot formation provisions of MIL-A-48078. In addition, inspection lots of Metal Parts Assembly with loaded ogive shall contain: a. Projectile metal parts of one lot interfix number from one manufacturer . b. Oxamide explosive composition of the same type from one lot inter,fix $number. c. Fuze well li
34、ners from one manufacturer produced in acco-rdance with the same drawing, same drawing revision, same spec i fi cat ion and same spec i fi cat ion 1: ev is ion . 4.2.2 Examinations. See MIL-A-48078. a. Sampling plans. Unless otherwise specified in the Classification of Defects and Test Tables, sampl
35、ing plans for major and minor defects shall be in accordance with MIL-STD-105, inspect ion Level II . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Y c CI z c a F !i e c .i Y u C 2 i YI 1 U - MIL-P-LLI005 23 a 7777706 0352833 3 43 E 8 rl CJ e e . .
36、 . - coco s1 1 1 mu) u) m eb m Lnm v) QI mm m m . 0. . . dpdp a, a, O0 O m O0 O o rlrl rl . 31 4J .Pl h U .I+ 3 3 Q a u u aJ aJ 3 3m 4 P Pu o OaJ a c u) c .Y .rl k 8 8 3 O a VI O a u C aJ a 4 3 Erl 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-n
37、p: A u m O O * W I ct. ii c r VI w I- d r b? O Y Y P Z o i= Y, d 3 Y, O 4 84 E i!i h U aJ c rl O .ri 5 3 u .ri m O 5 aJ 5 (d O cil c 0 .i4 3 3.i rn rn A 01 .lJ U O S 2 E c I U S 3 r- n m r) VL W U ru r U W CT L3 c3 n W LL 10 Provided by IHSNot for ResaleNo reproduction or networking permitted withou
38、t license from IHS-,-,-MIL-P-64005 13 777770b 0352835 7 W rl ki E % + ar c .i+ rl c U 3 -4 U -4 tn O 5 ar a a O I4 c U .4 3 3r III III 4 III U LI a pi rl a u ar c m N * cr e . - rl a 7 III .4 3 rl rl rl rlrl a, O O rl . . b *. *. d tn c .4 III III 4 E LI ar c I4 .d lua oa ar LILI arc uu . rl IIll 11
39、 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-zo 5 w wu H w PI cn 3 p: O Fr Z O c) w R H 2 . d u e .d Y g .A tn O 5 aJ 5 a O 4 c U 3 h rn rn .d MIL-P-64005 13 W 7779706 0352836 7 W 8 dPdp Wdp wo oww dPdp dpoo a, dpdp dp dPdp o* o O0 o O0 O o O0 -J
40、 O0 .O o orl dc; 498 I+ l-id dd U U e4 zu u a, a, Li P; ha OP u 32 h rl u aJ pi O E : U I- r n 3 n M Co m 3 = n x 3 v) a, U iu R aJ Y - 3 - 13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-.lJ a, ri ri 4 pi c w cu -3 -3 . . . MIL-P-64005 13 = 99999
41、06 0352838 2 i! rl m 1 c rlrlrlrirl mmmmm s1171 IIIIIIIIIIIIII .Pl .Pl .Pl .FI .FI 4 33333 a, c O z hn rll 14 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-4 MIL-P-64005 13 W 999990b 0352839 4 = MIL-P-64005 (AR) 4.4.3 Testinq. Testing is described
42、in the First Article and Quality Conformance Inspection Tables and the following: 4.4.3.1 ,Cavitation (see 3.4, except 3.4.5) . Cavitation defects are classified as follows: Cri tical: 1. Cavitation, cracks, piping, porosity or annular rings in segment A or B in excess of that permitted in Table I.
43、2. Cracks in excess of that permitted ijy 3.4.2. 3. Base separation (see 3.4.4) This test shall be performed on all loaded ogive assemblies (100 percent inspection) . The radiographic test shall be performed as specified in 4.5.1 using equipment in accordance with 4.4.4. Any ogive which has any one
44、of the above critical defects shall be classed defective and removed from the lot. 4.4.3.1.1 Base separation. The base separation inspection shall be performed either by sectioning of selected ogives (44.3.1.1.1) or by use of a radiographic standard (4.4.3.1.1.2) 4.4.3.1.1.1 Oqive sectioninq. Ogives
45、 showing the largest base separation as determined by radiographic examination shall be selected for sectioning at the following rate. From every group of 700 consecutively produced ogives or portion thereof one If the sample fails, the requirement of 3.4.4, then all ogives in that group which show
46、any indication of base separation by radiographic examination shall be rejected . 0 selectioning sample shall be selected. If radiographic examination of an entire group reveals no ogives with base separation, a sectioning sample shall be randomly selected. If the randomly selected sample fails to m
47、eet the requirement of 3.4.4, the entire group of ogives represented by that sample shall be rejected. The sectioning samples shall be tested in accordance with 4.5.3. 4.4.3.1.1.2 Radioqraphic standard for base separation. A radiographic standard for base separation shall be developed by the contrac
48、tor and approved by AMSMC-QAR-Q(D) prior to its use as a standard for acceptance. The standard shall utilize the bottom end of the ogive, cut approximately 1.25 inches above the ogive shoulder. A removable plug of epoxy shall be cast in the cut-off ogive. Radiographs at simulated base separations of .010, .O15 and .O20 inch shall be taken in order to brakcet the simulated 15 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-p-64005 13 797970b 0352840 0 MIL-P-64005 (AR) base separation of . 015 inch for sensitivity. The radiographi
