1、AMSC N/A FSC 5950 MIL-PRF-39010/15 20 September 2013 PERFORMANCE SPECIFICATION SHEET COILS, RADIO FREQUENCY, OPEN CONSTRUCTION, CERAMIC CORE, FIXED, SURFACE MOUNT ESTABLISHED RELIABILITY test condition B. Both end terminations are to be immersed simultaneously. Rates of immersion, dwell time and wit
2、hdrawal are human controlled. Magnet wire and bond are excluded from solder coverage. Resistance to solvents: When tested in accordance with MIL-STD-202, method 215, full immersion of part in solvents. Resistance to soldering heat: MIL-STD-202, method 210, test condition C. Mounting board to be SMD
3、test substrate per this document. Test to be performed after final electrical in qualification subgroup II; or after final electrical in group B subgroup 3 inspection. Flammability: Test is not required Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,
4、-MIL-PRF-39010/15 3 Overload: Test coil shall be mounted on SMD test substrate. Low temperature storage: Test coil shall be mounted on SMD test substrate. Vibration: Test coil shall be mounted on SMD test substrate. Mechanical shock: Test coil shall be mounted on SMD test substrate. Life: Test coil
5、shall be mounted on SMD test substrate. Moisture resistance: Method 106 of MIL-STD-202; polarization voltage not required. Step 7a shall be performed during any five of the first eight cycles only. Step 7b is not applicable. Test coil shall be mounted on SMD test substrate. SMD test substrate: Mater
6、ial shall be a minimum of 95 percent alumina with metallized areas for part mounting. The substrate shall not cause, or contribute to, any failure in any test which it is used. Coil mounting: Test coils are to be soldered to the SMD test substrate metallized areas using Sn63 solder, or equivalent, b
7、y any suitable method that does not exceed a temperature of 265C and a solder time period greater than five seconds. Table II electrical characteristics (final): For any subgroup test requiring coils to be mounted to an SMD test substrate, the electrical characteristics (final) measurements are to b
8、e referenced to the electrical characteristic (initial) measurements determined after the test coil is mounted to the test substrate. Part or identifying number (PIN): M39010/15-* (dash number from table 1) Part marking: Coil marking is not applicable due to body surface area size constraints. A non
9、corrosive label containing the military PIN, Cage code, date code, and lot symbol shall be inserted in each package, as shown in the following example: Example: M39010/01A1R0JM - - PIN 12345 - - - - - - - - - - - - CAGE code 0219B - - - - - - - - - - - - Date code and lot symbol The manufacturers so
10、urce code, date code, and lot symbol shall be in accordance with MIL-STD-1285. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39010/15 4 Table I Electrical characteristics (initial) and dash numbers Dash Number 1/ Inductance H 2/ Inductance
11、Test Frequency (MHz) Inductance Tolerance percent Q minimum 2/ Q Test frequency (MHz) Self Resonant Frequency min (MHz) 3/ DC resistance (25C) max (ohms) Rated DC current (mA) 4/ BR0082* BR010* BR012* BR015* 0.0082 0.010 0.012 0.015 100 50 50 50 20 10, 20 10, 20 10, 20 70 50 50 50 1500 500 500 500 6
12、000 4100 3300 2500 0.080 0.080 0.090 0.100 1,000 1,000 1,000 1,000 BR018* BR022* BR027* BR033* 0.018 0.022 0.027 0.033 50 50 50 50 10, 20 10, 20 10, 20 10, 20 50 55 55 60 500 350 350 350 2500 2400 1600 1600 0.110 0.120 0.130 0.140 1,000 1,000 1,000 1,000 BR039* BR047* BR056* BR068* 0.039 0.047 0.056
13、 0.068 50 50 50 50 10, 20 10, 20 5, 10 5, 10 60 65 65 65 350 350 350 350 1500 1500 1300 1300 0.150 0.160 0.180 0.200 1,000 1,000 1,000 1,000 BR082* BR10* BR12* BR15* 0.082 0.10 0.12 0.15 50 25 25 25 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 60 60 60 45 350 350 350 100 1000 1000 950 850 0.220 0.560 0.630 0.70
14、0 1,000 655 617 585 BR18* BR22* BR27* BR33* 0.18 0.22 0.27 0.33 25 25 25 25 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 45 45 45 45 100 100 100 100 750 700 600 570 0.770 0.840 0.910 1.05 560 535 515 475 BR39* BR43* BR47* BR56* 0.39 0.43 0.47 0.56 25 25 25 25 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 45 45 45 45 1
15、00 100 100 100 500 500 450 415 1.12 1.15 1.19 1.33 460 455 450 425 BR62* BR68* BR75* BR82* 0.62 0.68 0.75 0.82 25 25 25 25 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 45 45 45 45 100 100 100 100 375 375 360 350 1.40 1.47 1.54 1.61 415 405 395 385 See footnotes at end of table. Provided by IHSNot for ResaleN
16、o reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39010/15 5 Table I Electrical characteristics (initial) and dash numbers Dash Number 1/ Inductance H 2/ Inductance Test Frequency (MHz) Inductance Tolerance percent Q minimum 2/ Test frequency (MHz) Self Resonant Frequency m
17、in (MHz) 3/ DC resistance (25C) max (ohms) Rated DC current (mA) 4/ BR91* B1R0* B1R2* B1R5* 0.91 1.00 1.20 1.50 25 25 7.9 7.9 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 35 35 35 28 50 50 50 50 320 290 250 200 1.68 1.75 2.00 2.30 380 370 345 325 B1R8* B2R2* B2R7* B3R3* B3R9* B4R7* 1.80 2.20 2.70 3.30 3.90 4
18、.70 7.9 7.9 7.9 7.9 7.9 7.9 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 2, 5, 10 28 28 22 22 20 20 50 50 25 25 25 25 160 160 160 150 120 90 2.60 2.80 3.80 4.20 4.40 4.90 305 295 250 240 235 220 1/ The complete dash number will include two additional letters (indicated by *). The first additional le
19、tter will indicate the inductance tolerance (e.g. G = 2%, J = 5%, K = 10%, M = 20%) and the second additional letter will indicate the product level (e.g. C, M, P, R, S) and will be added to the end of the dash number. 2/ Inductance and Q are tested using HP4291A or equivalent. 3/ Self resonant freq
20、uency tested using HP8753C, HP4291A or equivalent 4/ The rated dc current is based on 90C ambient temperature with a 35C rise. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39010/15 6 Table II Electrical characteristics (final) Inspection G
21、roup Allowable variation from initial measurement Allowable percent from specified minimum value in electrical characteristics (initial) table Inductance (percent) DC resistance Self-resonant frequency Q Qualification inspection Group II Group IV Group VI 5 5 5 (3% + 0.001 ohm) (3% +0.001 ohm) 1/ 1/
22、 -10 -10 -10 Group B inspection Subgroup 1 Subgroup 3 Subgroup 4 5 5 5 (3% +0.001 ohm) (3% + 0.001 ohm) 1/ 1/ -10 -10 -10 1/ The self-resonant frequency shall not be less than the value specified in table I Referenced documents: In addition to MIL-PRF-39010, this document references: J-STD-002 MIL-S
23、TD-202 MIL-STD-883 MIL-STD-1285 Custodians: Preparing activity: Army CR Army - CR Navy EC Air Force 85 Agent: DLA CC DLA - CC Review activities: (Project 5950-2013-036) Army AR, CR4, MI Navy AS, CG, MC, OS, SH Air Force 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
