1、AMSC N/A FSC 5950 MIL-PRF-39010/18 20 September 2013 PERFORMANCE SPECIFICATION SHEET COILS, RADIO FREQUENCY, SHIELDED, MOLDED, FIXED, SURFACE MOUNT ESTABLISHED RELIABILITY test condition B. Both end terminations are to be immersed simultaneously. Rates of immersion, dwell time and withdrawal are hum
2、an controlled. Resistance to solvents: Test is not applicable Resistance to soldering heat: Method 210 of MIL-STD-202, test condition C. Mounting board to be SMD test substrate per this document. Test to be performed after final electrical in qualification subgroup II; or after final electrical in g
3、roup B subgroup 3 inspection. Overload: Test coil shall be mounted on SMD test substrate. Low temperature storage: Test coil shall be mounted on SMD test substrate. Vibration: Test coil shall be mounted on SMD test substrate. Mechanical shock: Test coil shall be mounted on SMD test substrate. Life:
4、Test coil shall be mounted on SMD test substrate. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39010/18 3 Moisture resistance: Method 106 of MIL-STD-202; polarization voltage not required. Step 7a shall be performed during any five of the
5、first eight cycles only. Step 7b is not applicable. Test coil shall be mounted on SMD test substrate. SMD test substrate: Material shall be a minimum of 95 percent alumina with metallized areas for part mounting. The substrate shall not cause, or contribute to, any failure in any test which it is us
6、ed. Coil mounting: Test coils are to be soldered to the SMD test substrate metallized areas using Sn63 solder, or equivalent, by any suitable method that does not exceed a temperature of 265C and a solder time period greater than five seconds. Table II electrical characteristics (final): For any sub
7、group test requiring coils to be mounted to an SMD test substrate, the electrical characteristics (final) measurements are to be referenced to the electrical characteristic (initial) measurements determined after the test coil is mounted to the test substrate. Part marking: These parts shall be lase
8、r marked. Part or identifying number (PIN): M39010/18-* (dash number from table 1) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39010/18 4 Table I Electrical characteristics (initial) and dash numbers Dash Number 1/ Inductance H 2/ Inducta
9、nce Tolerance percent Q minimum 2/ Test frequency (MHz) Self Resonant Frequency min (MHz) 3/ DC resistance (25C) max (ohms) Rated DC current (mA) 4/ Incremental current A150* A160* A180* A200* 15 16 18 20 5, 10 5 5,10 5 40 40 40 40 2.5 2.5 2.5 2.5 42 38 38 35 0.80 0.89 0.89 0.96 395 375 375 360 300
10、250 250 210 A220* A240* A270* A300* 22 24 27 30 5, 10 5 5,10 5 40 40 40 40 2.5 2.5 2.5 2.5 35 32 32 29 0.96 1.19 1.19 1.37 360 325 325 300 210 195 195 160 A330* A360* A390* A430* 33 36 39 43 5, 10 5 5,10 5 40 40 40 40 2.5 2.5 2.5 2.5 29 25 25 23 1.37 1.93 1.93 2.11 300 255 255 245 160 150 150 135 A4
11、70* A510* A560* A620* 47 51 56 62 5, 10 5 5,10 5 40 40 40 40 2.5 2.5 2.5 2.5 23 21 21 18 2.11 2.23 2.23 2.70 245 235 235 215 135 124 124 122 A680* A750* A820* A910* 68 75 82 91 5, 10 5 5,10 5 40 40 40 40 2.5 2.5 2.5 2.5 18 10.5 10.5 10 2.70 2.44 2.44 3.12 215 225 225 200 122 120 120 113 A101* A111*
12、A121* A131* 100 110 120 130 5, 10 5 5,10 5 40 55 55 55 2.5 .79 .79 .79 10 9.7 9.7 8.5 3.12 3.60 3.60 4.10 200 185 185 175 113 98 98 84 A151* A161* A181* A201* 150 160 180 200 5, 10 5 5,10 5 55 55 55 55 .79 .79 .79 .79 8.5 8.0 8.0 7.5 4.10 4.40 4.40 5.00 175 170 170 160 84 76 76 67 A221* A241* A271*
13、A301* 220 240 270 300 5, 10 5 5,10 5 55 55 55 55 .79 .79 .79 .79 7.5 7.0 7.0 6.5 5.00 5.80 5.80 6.40 160 145 145 140 67 60 60 55 A331* A361* A391* A431* 330 360 390 430 5, 10 5 5,10 5 55 60 60 60 .79 .79 .79 .79 6.5 6.2 6.2 5.7 6.40 7.40 7.40 9.50 140 130 130 115 55 46 46 43 A471* A511* A561* A621*
14、470 510 560 620 5, 10 5 5,10 5 60 60 60 60 .79 .79 .79 .79 5.7 4.7 4.7 4.5 9.50 10.5 10.5 11.8 115 110 110 105 43 40 40 38 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39010/18 5 Table I Electrical characteri
15、stics (initial) and dash numbers Dash Number 1/ Inductance H 2/ Inductance Tolerance percent Q minimum 2/ Test frequency (MHz) Self Resonant Frequency min (MHz) 3/ DC resistance (25C) max (ohms) Rated DC current (mA) 4/ Incremental current A681* A751* A821* A911* 680 750 820 910 5, 10 5 5, 10 5 60 6
16、0 60 60 .79 .79 .79 .79 4.5 4.2 4.2 3.8 11.8 13.0 13.0 17.5 105 100 100 85 38 33 33 29 A102* A112* A122* A132* 1,000 1,100 1,200 1,300 5, 10 5 5, 10 5 60 45 45 45 .79 .25 .25 .25 3.8 3.0 3.0 2.8 17.5 22.1 22.1 26.5 85 75 75 70 29 28 28 27 A152* A162* A182* A202* 1,500 1,600 1,800 2,000 5, 10 5 5, 10
17、 5 45 45 45 45 .25 .25 .25 .25 2.8 2.6 2.6 2.4 26.5 29.9 29.9 33.8 70 65 65 60 27 24 24 22 A222* A242* A272* A302* 2,200 2,400 2,700 3,000 5, 10 5 5, 10 5 45 45 45 45 .25 .25 .25 .25 2.4 2.2 2.2 2.0 33.8 47.3 47.3 53.0 60 50 50 45 22 20 20 19 A332* A362* A392* A432* 3,300 3,600 3,900 4,300 5, 10 5 5
18、, 10 5 45 45 45 45 .25 .25 .25 .25 2.0 1.9 1.9 1.7 53.0 73.8 73.8 81.6 45 40 40 38 19 17 17 15 A472* A512* A562* A622* 4,700 5,100 5,600 6,200 5, 10 5 5, 10 5 45 44 44 40 .25 .25 .25 .25 1.7 1.6 1.6 1.4 81.6 98.9 98.9 111 38 36 36 34 15 14 14 13 A682* A752* A822* A912* A103* 6,800 7,500 8,200 9,100
19、10,000 5, 10 5 5, 10 5 5,10 40 40 40 40 40 .25 .25 .25 .25 .25 1.4 1.2 1.2 1.0 1.0 111 119 119 139 139 34 32 32 30 30 13 12 12 11 11 1/ The complete dash number will include two additional letters (indicated by *). The first additional letter will indicate the inductance tolerance (e.g. J = 5%, K =
20、10%) and the second additional letter will indicate the product level (e.g. C, M, P, R, S) and will be added to the end of the dash number. 2/ Inductance and Q are tested using HP4194A with test fixture 16034E, or equivalent. 3/ Self resonant frequency tested using HP8753C, HP4291A, HP4194A or equiv
21、alent 4/ The rated dc current is based on 90C ambient temperature with a 15C rise. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39010/18 6 Table II Electrical characteristics (final) Inspection Group Allowable variation from initial measur
22、ement Allowable percent from specified minimum value in electrical characteristics (initial) table Inductance (percent) DC resistance Self-resonant frequency Q Qualification inspection Group II Group IV Group VI 5 10 5 (5% + 0.001 ohm) (2% +0.001 ohm) 1/ 1/ -10 -20 -20 Group B inspection Subgroup 1
23、Subgroup 3 Subgroup 4 5 5 10 (2% +0.001 ohm) (5% + 0.001 ohm) 1/ 1/ -20 -10 -20 1/ The self-resonant frequency shall not be less than the value specified in table I Referenced documents: In addition to MIL-PRF-39010, this document references: MIL-STD-202 MIL-STD-883 Custodians: Preparing activity: A
24、rmy CR Army - CR Navy EC Air Force 85 Agent: DLA CC DLA - CC Review activities: (Project 5950-2013-039) Army AR, CR4, MI Navy AS, CG, MC, OS, SH Air Force 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
