1、AMSC N/A FSC 5950 MIL-PRF-39010/19 20 September 2013 PERFORMANCE SPECIFICATION SHEET COILS, RADIO FREQUENCY, MOLDED, PHENOLIC CORE, FIXED, SURFACE MOUNT ESTABLISHED RELIABILITY test condition B. Both end terminations are to be immersed simultaneously. Rates of immersion, dwell time and withdrawal ar
2、e human controlled. Resistance to solvents: Test is not applicable Resistance to soldering heat: Method 210 of MIL-STD-202, test condition C. Mounting board to be SMD test substrate per this document. Test to be performed after final electrical in qualification subgroup II; or after final electrical
3、 in group B subgroup 3 inspection. Overload: Test coil shall be mounted on SMD test substrate. Low temperature storage: Test coil shall be mounted on SMD test substrate. Vibration: Test coil shall be mounted on SMD test substrate. Mechanical shock: Test coil shall be mounted on SMD test substrate. L
4、ife: Test coil shall be mounted on SMD test substrate. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39010/19 3 Moisture resistance: Method 106 of MIL-STD-202; polarization voltage not required. Step 7a shall be performed during any five of
5、 the first eight cycles only. Step 7b is not applicable. Test coil shall be mounted on SMD test substrate. SMD test substrate: Material shall be a minimum of 95 percent alumina with metallized areas for part mounting. The substrate shall not cause, or contribute to, any failure in any test which it
6、is used. Coil mounting: Test coils are to be soldered to the SMD test substrate metallized areas using Sn63 solder, or equivalent, by any suitable method that does not exceed a temperature of 265C and a solder time period greater than five seconds. Table II electrical characteristics (final): For an
7、y subgroup test requiring coils to be mounted to an SMD test substrate, the electrical characteristics (final) measurements are to be referenced to the electrical characteristic (initial) measurements determined after the test coil is mounted to the test substrate. Part or identifying number (PIN):
8、M39010/19-* (dash number from table 1) Part marking: The parts shall be laser marked. The PIN number marked on the coil shall not include the M39010/ identifier due to body surface area size constraints. Remaining part marking requirements of MIL-PRF-39010 apply. Provided by IHSNot for ResaleNo repr
9、oduction or networking permitted without license from IHS-,-,-MIL-PRF-39010/19 4 Table I Electrical characteristics (initial) and dash numbers Dash Number 1/ Inductance H 2/ Inductance Tolerance percent Q minimum 2/ Test frequency (MHz) Self Resonant Frequency min (MHz) 3/ DC resistance (25C) max (o
10、hms) Rated DC current (mA) 4/ BR10* BR11* BR12* BR13* 0.10 0.11 0.12 0.13 5, 10 5 5,10 5 40 40 40 38 25 25 25 25 680 640 640 600 0.080 0.090 0.090 0.100 1,380 1,300 1,300 1,230 BR15* BR16* BR18* BR20* 0.15 0.16 0.18 0.20 5, 10 5 5,10 5 38 35 35 33 25 25 25 25 600 550 550 510 0.100 0.120 0.120 0.140
11、1,230 1,120 1,120 1,040 BR22* BR24* BR27* BR30* 0.22 0.24 0.27 0.30 5, 10 5 5,10 5 33 33 33 30 25 25 25 25 510 430 430 410 0.140 0.160 0.160 0.220 1,040 975 975 830 BR33* BR36* BR39* BR43* 0.33 0.36 0.39 0.43 5, 10 5 5,10 5 30 30 30 30 25 25 25 25 410 365 365 330 0.220 0.300 0.300 0.350 830 710 710
12、660 BR47* BR51* BR56* BR62* 0.47 0.51 0.56 0.62 5, 10 5 5,10 5 30 30 30 28 25 25 25 25 330 300 300 275 0.350 0.500 0.500 0.600 660 550 550 500 BR68* BR75* BR82* BR91* B1R0* 0.68 0.75 0.82 0.91 1.00 5, 10 5 5,10 5 5, 10 28 28 28 25 25 25 25 25 25 25 275 250 250 230 230 0.600 0.850 0.850 1.00 1.00 500
13、 420 420 390 390 1/ The complete dash number will include two additional letters (indicated by *). The first additional letter will indicate the inductance tolerance (e.g. J = 5%, K = 10%) and the second additional letter will indicate the product level (e.g. C, M, P, R, S) and will be added to the
14、end of the dash number. 2/ Inductance and Q are tested using HP4194A with test fixture 16034E, or equivalent. 3/ Self resonant frequency tested using HP8753C, HP4291A or equivalent 4/ The rated dc current is based on 90C ambient temperature with a 35C rise. Provided by IHSNot for ResaleNo reproducti
15、on or networking permitted without license from IHS-,-,-MIL-PRF-39010/19 5 Table II Electrical characteristics (final) Inspection Group Allowable variation from initial measurement Allowable percent from specified minimum value in electrical characteristics (initial) table Inductance (percent) DC re
16、sistance Self resonant frequency Q Qualification inspection Group II Group IV Group VI 2 5 5 (3% + 0.001 ohm) (2% +0.001 ohm) 1/ 1/ -10 -10 -15 Group B inspection Subgroup 1 Subgroup 3 Subgroup 4 5 2 5 (2% +0.001 ohm) (3% + 0.001 ohm) 1/ 1/ -15 -10 -10 1/ The self-resonant frequency shall not be les
17、s than the value specified in table I Referenced documents: In addition to MIL-PRF-39010, this document references: MIL-STD-202 MIL-STD-883 Custodians: Preparing activity: Army CR Army - CR Navy EC Air Force 85 Agent: DLA CC DLA - CC Review activities: (Project 5950-2013-040) Army AR, CR4, MI Navy A
18、S, CG, MC, OS, SH Air Force 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
