1、AMSC N/A FSC 5905 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. INCH-POUND MIL-PRF-55342/12A w/ Amendment 3 16 August 2012 SUPERSEDING MIL-PRF-55342/12A w/ Amendment 2 15 October 2007 PERFORMANCE SPECIFICATION RESISTORS, CHIP, FIXED, FILM, NONESTABLISHED RELIABILI
2、TY, ESTABLISHED RELIABILITY, SPACE LEVEL, STYLE RM0603 This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-55342. 1. SCOPE * 1.1 Scope. T
3、his specification covers the requirements for style RM0603, fixed, film, chip, nonestablished reliability, established reliability, and space level resistors. This style is available in characteristic H, characteristic E, characteristic K, characteristic L, and characteristic M, resistance tolerance
4、s .1 percent, .25 percent, .5 percent, 1 percent, 2 percent, 5 percent, and 10 percent, and all termination materials. Designers are CAUTIONED on using these resistors in high power pulses applications (see 6.5). 1.2 Part or Identifying Number (PIN). Chip resistors covered by this specification are
5、identified by a PIN which consists of the basic number of this specification and a coded dash number. The PIN is in the following form: M55342H12 B1E00M | | | | Performance specification number Coded dash number The coded dash number is derived in accordance with MIL-PRF-55342. Comments, suggestions
6、, or questions on this document should be addressed to US Army Communications - Electronics Command RDEC, ATTN: AMSRD-CER-PR-D, Aberdeen Proving Ground, Bldg. 6010 K-130, C2/CNT East, MD 21005 or emailed to usarmy.APG.cerdec.mbx.standardization-crxmail.mil. Since contact information can change, you
7、may want to verify the currency of this address information using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-55342/12A w/ Amendment 3 2 2. APPLICABLE DOCUMENTS 2.1 General. The documen
8、ts listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list,
9、 document users are cautioned that they must meet all specified requirements documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks for
10、ms a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-55342 - Resistors, Chip, Fixed, Film, Nonestablished Reliability, Established Reliability,
11、 Space Level, General Specification for. * (Copies of these documents are available online at https:/assist.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) * 2.3 Order of precedence. Unless otherwise noted herein or
12、 in the contract, in the event of a conflict between the text of this document and the references cited herein (except for related, specification sheets), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemp
13、tion has been obtained. 3. REQUIREMENTS 3.1 General. The requirements for acquiring the product described herein shall consist of this document and MIL-PRF-55342. 3.2 Interface and physical dimensions. Resistors shall meet the interface and physical dimensions specified on figure 1, as applicable. 3
14、.3. Power rating. The power rating for all characteristics shall be 100 milliwatts. 3.4 Voltage rating. The maximum continuous working voltage shall not exceed 50 volts. 3.5 Resistance and resistance tolerance. Minimum and maximum resistance values and associated resistance tolerances shall be as li
15、sted in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-55342/12A w/ Amendment 3 3 Configuration A Configuration B Inches mm Inches mm 0.005 0.13 0.032 0.81 0.006 0.15 0.033 0.84 0.010 0.25 0.060 1.52 0.012 0.31 0.064 1.63 0.015 0.38
16、 Configuration Dimension A Inch Dimension B inch Dimension C Inch Dimension D Inch Dimension E Inch A .060 .005 .032 .005 .010 / .033 .010 .005 N/A B .064 .006 .032 .005 .010 / .033 .012 .005 .015 .005 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only.
17、3. Unless otherwise specified, tolerance is .005 (0.13 mm). 4. The pictorial view of the styles above is given as representative of the envelope of the item. Slight deviations from the outline shown, which are contained within the envelope, and do not alter the functional aspects of the device are a
18、cceptable. 5. Configuration A covers termination materials D, T, and W. 6. Configuration B covers termination materials B, C, G, and U. FIGURE 1. Style RM0603. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-55342/12A w/ Amendment 3 4 * TABLE
19、 I. Minimum and maximum resistance values. Resistance tolerance Minimum resistance Maximum resistance Percent () 0.1 0.25 0.5 1.0 2.0 5.0 10.0 1.0 ohm 22.0 megohms 4. VERIFICATION 4.1 Verification. Verification shall be in accordance with MIL-PRF-55342. 5. PACKAGING 5.1 Packaging. For acquisition pu
20、rposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requir
21、ements are maintained by the Inventory Control Points packaging activity within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM p
22、roducts, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Notes The notes specified in MIL-PRF-55342 are applicable to this specification. 6.2 Acquisition requirements.
23、Acquisition documents should specify the following: a. Title, number, date of this specification, the applicable associated specification, and the complete PIN (see 1.2). * b. Unless otherwise specified (see 2.1), the versions of the individual documents referenced will be those in effect on the dat
24、e of release of the solicitation. c. Packaging requirements (see 5.1). (i.e. Electrostatic discharge (ESD) sensitive packaging). d. Allowable substitution (see MIL-PRF-55342). e. If marking is required (see MIL-PRF-55342). Provided by IHSNot for ResaleNo reproduction or networking permitted without
25、license from IHS-,-,-MIL-PRF-55342/12A w/ Amendment 3 5 6.3 Tolerance for wraparound termination. The added tolerance for the wraparound type termination is intended to apply only to termination, metallization, and pretinning material. 6.4 Electrostatic charge effects. Under relatively low humidity
26、conditions, some types of film resistors, particularly those with small dimensions and high sheet resistivity materials, are prone to sudden significant changes in resistance (usually reductions in value) and to changes in temperature coefficient of resistance as a result of discharge of static char
27、ges built up on associated objects during handling, packaging, or shipping. Substitution of more suitable implements and materials can help minimize this problem. For example, use of cotton gloves, static eliminator devices, air humidifiers, and operator and workbench grounding systems can reduce st
28、atic buildup during handling. Means of alleviating static problems during shipment include elimination of loose packaging of resistors and use of metal foil (conductive) and static dissipation packaging materials. Direct shipments to the government are controlled by MIL-DTL-39032 which specifies a p
29、reventive packaging procedure. * 6.5 Pulse applications. Designers are CAUTIONED on using these resistors in high power pulse applications. Since they have not been qualified nor tested for such applications, damage and premature failure are possible. These resistors only see a five second short tim
30、e overload as part of the group B inspection of this specification. 6.6 Amendment notations. The margins of this specification are marked with asterisks to indicate modifications generated by this amendment. This was done as a convenience only and the Government assumes no liability whatsoever for a
31、ny inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations. Custodians: Preparing activity: Army - CR Army - CR Navy - EC Air Force - 85 Agent: DLA - CC DLA - CC NASA - NA
32、Review activities: Army - AR, AT, AV, CR4 (Project 5905-2009-064) Navy - AS, CG, MC, OS Air Force - 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
