1、AMSC N/A FSC 5910 DISTRIBUTION STATEMENT A Approved for public release, distribution is unlimited. INCH-POUND MIL-PRF-55365/13B 18 October 2012 SUPERSEDING MIL-PRF-55365/13A 28 January 2011 PERFORMANCE SPECIFICATION SHEET CAPACITORS, CHIP, FIXED, TANTALUM, POLARIZED, ESTABLISHED RELIABILITY AND NONE
2、STABLISHED RELIABILITY, STYLES CWR16 and CWR26 This specification sheet is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-55365. FIGURE 1. Styles CWR16 an
3、d CWR26 conformally coated capacitors. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-55365/13B 2 Case size L W H P .015 (0.38) .015 (0.38) .015 (0.38) .005 (0.13) A .100 (2.54) .050 (1.27) .050 (1.27) .030 (0.76) B .150 (3.81) .050 (1.27) .
4、050 (1.27) .030 (0.76) C .200 (5.08) .050 (1.27) .050 (1.27) .030 (0.76) D .150 (3.81) .100 (2.54) .050 (1.27) .030 (0.76) E .200 (5.08) .100 (2.54) .050 (1.27) .030 (0.76) F .220 (5.59) .135 (3.43) .070 (1.78) .030 (0.76) G .265 (6.73) .110 (2.79) .110 (2.79) .050 (1.27) H .285 (7.24) .150 (3.81) .
5、110 (2.79) .050 (1.27) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are in parentheses and given for general information only. 3. Metric equivalents are in millimeters. 4. These capacitors are designed for mounting by dip soldering, thermo-compression bonding, reflow soldering, or other
6、 conventional means. 5. Cathode terminal may be epoxy coated on one surface for polarity identification. 6. Solderable surfaces are only those surfaces designated as such. 7. Anode and cathode terminals may be two-sided through five-sided, and may not be the same on some designs, but will meet all s
7、pecification requirements. 8. The anode terminal shall be identified by the riser wire connection, which may extend the case size .015 inch (0.38 mm) maximum. The riser wire weld area is not solderable. The riser wire connection shall have a continuous weld of a minimum of 25 percent of the contact
8、surface. 9. When solder coated terminations are required, add .015 inch (0.38 mm) to termination dimension tolerances. 10. CWR16 capacitors have higher capacitance values than CWR06s of the same case size and voltage rating (see MIL-PRF-55365/4). CWR26s are low ESR versions of both CWR06s and CWR16s
9、. FIGURE 1. Styles CWR16 and CWR26 conformally coated capacitors - Continued. REQUIREMENTS: Dimensions and configuration: See figure 1. Termination finish: In accordance with termination finishes B, C, H, or K of MIL-PRF-55365. DC rated voltage: See table I or table II. Above +85C, voltage derating
10、is required (see MIL-PRF-55365). Operating temperature range: -55C to +125C. Product level designator: In accordance with MIL-PRF-55365. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-55365/13B 3 DC leakage (DCL): See table I or table II. Ca
11、pacitance: See table I or table II. Capacitance tolerance: 5 percent (J), 10 percent (K), or 20 percent (M). Dissipation factor (DF): See table I or table II. Equivalent series resistance (ESR) at 100 kHz: In accordance with MIL-PRF-55365 (see table I or table II). Resistance to soldering heat: In a
12、ccordance with MIL-PRF-55365. Stability at low and high temperatures: In accordance with MIL-PRF-55365. Surge voltage: In accordance with MIL-PRF-55365. Life: 2,000 hours: In accordance with MIL-PRF-55365 10,000 hours: In accordance with MIL-PRF-55365 Solderability: In accordance with MIL-PRF-55365
13、except that following steam aging, test samples may have a 30 minute bake out at +150C prior to solder dipping and all terminations shall exhibit a continuous solder coating free from defects for a minimum of 75 percent of the critical area of any individual termination. TABLE I. Style CWR16 charact
14、eristics. Part or identifying number (PIN) 1/ DC rated voltage (+85C) (Volts) Cap. (nom) (F) DC Leakage (max) (A) Dissipation factor (max) (percent) Max ESR 100 kHz +25C (Ohms) Case size +25C +85C +125C +25C +85C +125C -55C CWR16C-335-A- 4 3.3 1 10 12 6 8 8 12 A CWR16C-475-A- 4 4.7 1 10 12 6 8 8 12
15、A CWR16C-685-A- 4 6.8 1 10 12 6 8 8 12 A CWR16C-106-B- 4 10 1 10 12 8 10 10 8 B CWR16C-156-B- 4 15 1 10 12 8 10 10 8 B CWR16C-226-B- 4 22 1 10 12 8 10 10 8 B CWR16C-226-D- 4 22 1 10 12 8 10 12 4 D CWR16C-336-D- 4 33 2 20 24 8 10 12 4 D CWR16C-336-E- 4 33 2 20 24 8 10 12 3 E CWR16C-476-E- 4 47 2 20 2
16、4 8 10 12 3 E CWR16C-686-E- 4 68 3 30 36 8 10 12 3 E CWR16C-107-F- 4 100 4 40 48 10 12 12 2 F CWR16C-157-G- 4 150 6 60 72 10 12 12 1 G CWR16C-227-H- 4 220 8 80 96 10 12 12 1 H CWR16C-337-H- 4 330 10 100 120 10 12 12 0.9 H CWR16D-335-A- 6 3.3 1 10 12 6 8 8 12 A CWR16D-475-A- 6 4.7 1 10 12 6 8 8 12 A
17、CWR16D-685-B- 6 6.8 1 10 12 6 8 8 8 B CWR16D-106-B- 6 10 1 10 12 6 8 8 8 B CWR16D-156-B- 6 15 1 10 12 8 10 10 8 B CWR16D-156-D- 6 15 1 10 12 8 10 12 5 D CWR16D-156-E- 6 15 1 10 12 8 10 12 3 E CWR16D-226-D- 6 22 1 10 12 6 8 8 5 D CWR16D-226-E- 6 22 2 20 24 8 10 12 3.5 E CWR16D-336-E- 6 33 2 20 24 6 8
18、 8 3.5 E CWR16D-476-F- 6 47 3 30 36 8 10 12 3.5 F See footnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-55365/13B 4 TABLE I. Style CWR16 characteristics - Continued. Part or identifying number (PIN) 1/ DC rated voltage
19、 (+85C) (Volts) Cap. (nom) (F) DC Leakage (max) (A) Dissipation factor (max) (percent) Max ESR 100 kHz +25C (Ohms) Case size +25C +85C +125C +25C +85C +125C -55C CWR16D-686-F- 6 68 4 40 48 10 12 12 1.5 F CWR16D-686-G- 6 68 4 40 48 10 12 12 1 G CWR16D-107-G- 6 100 6 60 72 10 12 12 1.1 G CWR16D-157-G-
20、 6 150 10 100 120 10 12 12 1.1 G CWR16D-227-H- 6 220 10 100 120 10 12 12 0.9 H CWR16D-337-H- 6 330 20 200 240 10 12 12 0.9 H CWR16F-225-A- 10 2.2 1 10 12 6 8 8 12 A CWR16F-335-A- 10 3.3 1 10 12 6 8 8 12 A CWR16F-475-B- 10 4.7 1 10 12 6 8 8 8 B CWR16F-475-C- 10 4.7 1 10 12 6 8 8 5.5 C CWR16F-685-B- 1
21、0 6.8 1 10 12 6 8 8 8 B CWR16F-685-C- 10 6.8 1 10 12 6 8 8 5.5 C CWR16F-685-D- 10 6.8 1 10 12 6 8 8 5 D CWR16F-106-B- 10 10 1 10 12 8 10 10 8 B CWR16F-106-C- 10 10 1 10 12 6 8 8 5.5 C CWR16F-106-D- 10 10 1 10 12 6 8 8 4 D CWR16F-106-E- 10 10 1 10 12 6 8 8 3.5 E CWR16F-156-D- 10 15 1 10 12 6 8 8 5 D
22、CWR16F-156-E- 10 15 2 20 24 8 10 10 3 E CWR16F-226-E- 10 22 3 30 36 8 10 10 2 E CWR16F-336-F- 10 33 3 30 36 8 10 10 1.5 F CWR16F-476-F- 10 47 4 40 48 10 12 12 1.5 F CWR16F-476-G- 10 47 4 40 48 10 12 12 1 G CWR16F-686-G- 10 68 6 60 72 10 12 12 1.1 G CWR16F-107-G- 10 100 10 100 120 10 12 12 1.1 G CWR1
23、6F-107-H- 10 100 10 100 120 10 12 12 0.9 H CWR16F-157-H- 10 150 15 150 180 10 12 12 0.9 H CWR16F-227-H- 10 220 20 200 240 10 12 12 0.9 H CWR16H-105-A- 15 1 1 10 12 6 8 8 15 A CWR16H-155-A- 15 1.5 1 10 12 6 8 8 15 A CWR16H-225-A- 15 2.2 1 10 12 6 8 8 15 A CWR16H-335-B- 15 3.3 1 10 12 6 8 8 9 B CWR16H
24、-475-B- 15 4.7 1 10 12 6 8 8 5 B CWR16H-475-C- 15 4.7 1 10 12 6 8 8 5.5 C CWR16H-475-D- 15 4.7 1 10 12 6 8 8 6 D CWR16H-685-D- 15 6.8 1 10 12 6 8 8 6 D CWR16H-685-E- 15 6.8 1 10 12 8 10 12 3 E CWR16H-106-D- 15 10 2 20 24 6 8 8 6 D CWR16H-106-E- 15 10 2 20 24 6 8 8 4 E CWR16H-156-E- 15 15 2 20 24 6 8
25、 8 4 E CWR16H-156-F- 15 15 2 20 24 8 10 10 3 F CWR16H-226-F- 15 22 3 30 36 8 10 10 3 F CWR16H-336-F- 15 33 5 50 60 6 8 8 3 F CWR16H-336-G- 15 33 6 60 72 8 10 10 1.1 G CWR16H-476-G- 15 47 10 100 120 8 10 10 1.1 G CWR16H-476-H- 15 47 10 100 120 8 10 10 0.9 H CWR16H-686-G- 15 68 10 100 120 8 10 10 1.1
26、G CWR16H-686-H- 15 68 10 100 120 8 10 10 0.9 H CWR16H-107-H- 15 100 15 150 180 10 12 12 0.9 H CWR16J-684-A- 20 0.68 1 10 12 6 8 8 15 A CWR16J-105-A- 20 1 1 10 12 6 8 8 15 A CWR16J-155-B- 20 1.5 1 10 12 6 8 8 9 B CWR16J-225-B- 20 2.2 1 10 12 6 8 8 9 B CWR16J-335-D- 20 3.3 1 10 12 6 8 8 6 D CWR16J-475
27、-E- 20 4.7 1 10 12 6 8 8 6 E CWR16J-685-E- 20 6.8 2 20 24 6 8 8 5 E See footnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-55365/13B 5 TABLE I. Style CWR16 characteristics - Continued. Part or identifying number (PIN) 1
28、/ DC rated voltage (+85C) (Volts) Cap. (nom) (F) DC Leakage (max) (A) Dissipation factor (max) (percent) Max ESR 100 kHz +25C (Ohms) Case size +25C +85C +125C +25C +85C +125C -55C CWR16J-106-E- 20 10 2 20 24 6 8 8 5 E CWR16J-106-F- 20 10 2 20 24 6 8 8 3 F CWR16J-156-F- 20 15 3 30 36 6 8 8 3 F CWR16J
29、-226-G- 20 22 4 40 48 8 10 10 2.5 G CWR16J-336-H- 20 33 6 60 72 8 10 10 0.9 H CWR16J-476-H- 20 47 10 100 120 8 10 10 0.9 H CWR16K-474-A- 25 0.47 1 10 12 6 8 8 15 A CWR16K-105-B- 25 1 1 10 12 6 8 8 10 B CWR16K-225-D- 25 2.2 1 10 12 6 8 8 6 D CWR16K-335-E- 25 3.3 1 10 12 6 8 8 4 E CWR16K-685-F- 25 6.8
30、 2 20 24 6 8 8 3 F CWR16K-156-G- 25 15 4 40 48 6 8 8 1.4 G CWR16K-226-G- 25 22 6 60 72 6 8 8 1.4 G CWR16K-226-H- 25 22 6 60 72 6 8 8 0.9 H CWR16K-336-H- 25 33 10 100 120 8 10 10 0.9 H CWR16M-334-A- 35 0.33 1 10 12 6 8 8 22 A CWR16M-685-G- 35 6.8 3 30 36 6 8 8 1.5 G CWR16M-106-H- 35 10 4 40 48 8 10 1
31、0 0.9 H CWR16M-156-H- 35 15 6 60 72 6 8 8 0.9 H 1/ Complete PIN shall include additional symbols to indicate capacitance tolerance, product level designator, and surge current option letter. If surge current is not required, the last “-“ shall be replaced with the letter Z. TABLE II. Style CWR26 cha
32、racteristics. Part or identifying number (PIN) 1/ DC rated voltage (+85C) (Volts) Cap. (nom) (F) DC Leakage (max) (A) Dissipation factor (max) (percent) Max ESR 100 kHz +25C (Ohms) Case size +25C +85C +125C +25C +85C +125C -55C CWR26C-225-A- 4 2.2 1 10 12 6 8 8 4 A CWR26C-335-A- 4 3.3 1 10 12 6 8 8
33、6 A CWR26C-475-A- 4 4.7 1 10 12 6 8 8 6 A CWR26C-475-B- 4 4.7 1 10 12 6 8 8 3.2 B CWR26C-685-A- 4 6.8 1 10 12 6 8 8 6 A CWR26C-106-B- 4 10 1 10 12 8 10 10 3.2 B CWR26C-106-D- 4 10 1 10 12 8 8 10 1.3 D CWR26C-156-B- 4 15 1 10 12 8 10 10 3.2 B CWR26C-156-E- 4 15 1 10 12 8 10 12 1 E CWR26C-226-B- 4 22
34、1 10 12 8 10 10 3.2 B CWR26C-226-D- 4 22 1 10 12 8 10 12 1.3 D CWR26C-336-D- 4 33 2 20 24 8 10 12 1.3 D CWR26C-336-E- 4 33 2 20 24 8 10 12 0.9 E CWR26C-476-E- 4 47 2 20 24 8 10 12 0.9 E CWR26C-686-E- 4 68 3 30 36 8 10 12 0.9 E CWR26C-107-F- 4 100 4 40 48 10 12 12 0.550 F CWR26C-157-G- 4 150 6 60 72
35、10 12 12 0.250 G CWR26C-227-H- 4 220 8 80 96 10 12 12 0.200 H CWR26C-337-H- 4 330 10 100 120 10 12 12 0.180 H CWR26D-155-A- 6 1.5 1 10 12 6 8 8 4 A CWR26D-335-A- 6 3.3 1 10 12 6 8 8 6 A CWR26D-335-B- 6 3.3 1 10 12 6 8 8 3.2 B CWR26D-475-A- 6 4.7 1 10 12 6 8 8 6 A CWR26D-475-C- 6 4.7 1 10 12 6 8 8 2.
36、2 C CWR26D-685-B- 6 6.8 1 10 12 6 8 8 3.2 B See footnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-55365/13B 6 TABLE II. Style CWR26 characteristics - Continued. Part or identifying number (PIN) 1/ DC rated voltage (+85
37、C) (Volts) Cap. (nom) (F) DC Leakage (max) (A) Dissipation factor (max) (percent) Max ESR 100 kHz +25C (Ohms) Case size +25C +85C +125C +25C +85C +125C -55C CWR26D-685-D- 6 6.8 1 10 12 6 8 8 1.5 D CWR26D-106-B- 6 10 1 10 12 6 8 8 3.2 B CWR26D-106-E- 6 10 1 10 12 8 10 12 1 E CWR26D-156-B- 6 15 1 10 1
38、2 8 10 10 3.2 B CWR26D-156-D- 6 15 1 10 12 8 10 12 1.7 D CWR26D-156-E- 6 15 1 10 12 8 10 12 0.9 E CWR26D-226-D- 6 22 1 10 12 6 8 8 1.7 D CWR26D-226-E- 6 22 2 20 24 8 10 12 1 E CWR26D-226-F- 6 22 2 20 24 8 10 12 0.6 F CWR26D-336-E- 6 33 2 20 24 6 8 8 1 E CWR26D-476-F- 6 47 3 30 36 8 10 12 1 F CWR26D-
39、476-G- 6 47 3 30 36 10 12 12 0.275 G CWR26D-686-F- 6 68 4 40 48 10 12 12 0.400 F CWR26D-686-G- 6 68 4 40 48 10 12 12 0.250 G CWR26D-686-H- 6 68 4 40 48 10 12 12 0.180 H CWR26D-107-G- 6 100 6 60 72 10 12 12 0.275 G CWR26D-157-G- 6 150 10 100 120 10 12 12 0.275 G CWR26D-227-H- 6 220 10 100 120 10 12 1
40、2 0.180 H CWR26D-337-H- 6 330 20 200 240 10 12 12 0.180 H CWR26F-105-A- 10 1 1 10 12 6 8 8 5 A CWR26F-225-A- 10 2.2 1 10 12 6 8 8 6 A CWR26F-225-B- 10 2.2 1 10 12 6 8 8 3.2 B CWR26F-335-A- 10 3.3 1 10 12 6 8 8 6 A CWR26F-335-C- 10 3.3 1 10 12 6 8 8 2.2 C CWR26F-475-B- 10 4.7 1 10 12 6 8 8 3.2 B CWR2
41、6F-475-C- 10 4.7 1 10 12 6 8 8 2.2 C CWR26F-475-D- 10 4.7 1 10 12 6 8 8 1.5 D CWR26F-685-B- 10 6.8 1 10 12 6 8 8 3.2 B CWR26F-685-C- 10 6.8 1 10 12 6 8 8 2.2 C CWR26F-685-D- 10 6.8 1 10 12 6 8 8 1.7 D CWR26F-685-E- 10 6.8 1 10 12 6 8 8 1 E CWR26F-106-B- 10 10 1 10 12 8 10 10 3.2 B CWR26F-106-C- 10 1
42、0 1 10 12 6 8 8 2.2 C CWR26F-106-D- 10 10 1 10 12 6 8 8 1.3 D CWR26F-106-E- 10 10 1 10 12 6 8 8 1 E CWR26F-156-D- 10 15 1 10 12 6 8 8 1.7 D CWR26F-156-E- 10 15 2 20 24 8 10 10 0.9 E CWR26F-156-F- 10 15 2 20 24 8 10 10 0.7 F CWR26F-226-E- 10 22 3 30 36 8 10 10 0.6 E CWR26F-336-F- 10 33 3 30 36 8 10 1
43、0 0.4 F CWR26F-336-G- 10 33 3 30 36 10 12 12 0.275 G CWR26F-476-F- 10 47 4 40 48 10 12 12 0.4 F CWR26F-476-G- 10 47 4 40 48 10 12 12 0.250 G CWR26F-476-H- 10 47 5 50 60 10 12 12 0.180 H CWR26F-686-G- 10 68 6 60 72 10 12 12 0.275 G CWR26F-107-G- 10 100 10 100 120 10 12 12 0.275 G CWR26F-107-H- 10 100
44、 10 100 120 10 12 12 0.180 H CWR26F-157-H- 10 150 15 150 180 10 12 12 0.180 H CWR26F-227-H- 10 220 20 200 240 10 12 12 0.180 H CWR26H-684-A- 15 0.68 1 10 12 6 8 8 6 A CWR26H-105-A- 15 1 1 10 12 6 8 8 7.5 A CWR26H-155-A- 15 1.5 1 10 12 6 8 8 7.5 A CWR26H-155-B- 15 1.5 1 10 12 6 8 8 3.2 B CWR26H-225-A
45、- 15 2.2 1 10 12 6 8 8 7.5 A CWR26H-225-C 15 2.2 1 10 12 6 8 8 2.2 C CWR26H-335-B- 15 3.3 1 10 12 6 8 8 3.6 B See footnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-55365/13B 7 TABLE II. Style CWR26 characteristics - Co
46、ntinued. Part or identifying number (PIN) 1/ DC rated voltage (+85C) (Volts) Cap. (nom) (F) DC Leakage (max) (A) Dissipation factor (max) (percent) Max ESR 100 kHz +25C (Ohms) Case size +25C +85C +125C +25C +85C +125C -55C CWR26H-335-D- 15 3.3 1 10 12 6 8 8 1.7 D CWR26H-475-B- 15 4.7 1 10 12 6 8 8 2
47、 B CWR26H-475-C- 15 4.7 1 10 12 6 8 8 2.2 C CWR26H-475-D- 15 4.7 1 10 12 6 8 8 2 D CWR26H-475-E- 15 4.7 1 10 12 6 8 8 1.2 E CWR26H-685-D- 15 6.8 1 10 12 6 8 8 2 D CWR26H-685-E- 15 6.8 1 10 12 8 10 12 0.9 E CWR26H-106-D- 15 10 2 20 24 6 8 8 2 D CWR26H-106-E- 15 10 2 20 24 6 8 8 1.2 E CWR26H-106-F- 15
48、 10 2 20 24 6 8 8 0.667 F CWR26H-156-E- 15 15 2 20 24 6 8 8 1.2 E CWR26H-156-F- 15 15 2 20 24 8 10 10 0.8 F CWR26H-226-F- 15 22 3 30 36 8 10 10 0.8 F CWR26H-226-G- 15 22 4 40 48 6 8 8 0.275 G CWR26H-336-F- 15 33 5 50 60 6 8 8 0.8 F CWR26H-336-G- 15 33 6 60 72 8 10 10 0.275 G CWR26H-336-H- 15 33 5 50 60 8 8 10 0.18 H CWR26H-476-G- 15 47 10 100 120 8 10 10 0.275 G CWR26H-476-H- 15 47 10 100 120 8 10 10 0.180 H CWR26H-686-G- 15 68 10 100 12
