1、 MIL-R-LqbL17 9 7777706 0377353 2 - c?“s(I-s-L- MIL-R-14649 1 April 1987 a MILITARY SPECIFICATION ROSETTES, GENERAL SPECIFICATION FOR This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification establishes the requiremen
2、ts for Rosettes used by the Department of Defense and Various Federal Agencies. 1.2 Classification. The rosettes covered by this specification shall be as specified on the applicable specification sheet (see supplement 1 and 6.2). 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specification
3、s and standards. The following specifications and stan- dards form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and
4、 supplement thereto, cited in the solicitation. SPECIFICATIONS FEDERAL NN-P- 71 - Pallets, Material Handling, Wood, Stringer Construction, 2-way and 4-way (partial) PPP-B-636 - Boxes, Shipping, Fiberboard MILITARY MIL-P-15011 - Pallets, Material Handling, Wood Post Construction, 4-way entry (See sup
5、plement 1 for list of associated specifications) Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be used in improving this document should be addressed to: Director, The Institute of Heraldry, US Army, Cameron Station, Alexandria, VA 22304-5050, by using
6、the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter, FSC 8455 AMSC N/A DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. O r 7 THIS DOCUMENT CONTAINS 12 PAGES. Provided by IHSNot for Resale
7、No reproduction or networking permitted without license from IHS-,-,-_- MIL-R-34649 4 999990b 0379352 Li - MIL-R-14649 STANDARDS FEDERAL FED-STD-I91 - Textile, Test Methods MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by MIL-STD-129 - Marking for Shipment and Storage MIL-STD-
8、147 - Palletized Unit Loads MIL-STD-2073-1 - DOD Materiel Procedures for Development and Attributes Application of Packaging requirements, 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this specificat
9、ion to the extent specified herein. issues shall be those in effect on the date of the solicitation. Unless otherwise specified, the DRAWINGS THE INSTITUTE OF HERALDRY B- 6- 7 - Rosettes, Metal Forms B-13-12 - Attaching Devices, Heraldic, Prong and clutch type, (Copies of specifications, standards,
10、and other Governments documents required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting officer.) 2.2 Other publications. The following document forms a part of this specification to the extent speci
11、fied herein. Unless otherwise specified, the issues of the documents which are DOD adopted shall be those listed in the issue of the DODISS specified in the solicitation. the issues of documents not listed in the DODISS shall be the issue of the nongovernment documents which is current on the date o
12、f the solicitation. Unless otherwise specified, THE COLOR ASSOCIATION OF THE UNITED STATES The Standard Color Reference of America, Tenth Edition. United States Army Color Card, The Official Colors for Branches, DOD Standard Shades for Heraldic Yarns for Embroidery and Ribbons, Agencies, etc. 1974.
13、2 d Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-19697 4 7779706 0377153 b MIL-R-I4649 (Application for copies should be addressed to The Color Association of the United States, Inc., 343 Lexington Avenue, New York, NY 10916.) AMERICAN SOCIE
14、TY FOR TESTING AND MATERIALS ASTM-D-3951 - Standard Practice for Commercial Packaging. (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race St., Philadelphia PA 19103.) and (Nongovernment standards and other publications are normally available from
15、 the organizations which prepare or which distribute the documents. These documents also may be available in or through libraries or other informational services.) 2.3 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein, (except for
16、associated detail specifications, specification sheets or MS standards) the text of this specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Specification sheet
17、s. The individual item requirements shall be as specified herein and in accordance with the applicable specification sheets. In the event of any conflict between requirements of this specification and the specification sheets, the latter shall govern. 3.2 Guide samples. Unless otherwise specified (s
18、ee 6.31, samples shall be furnished by the contracting officer to be used for guidance, information and as a standard for colorfastness. in the guide samples in which event the specification shall govern. Variation from this specification may appear 3.3 First article. Unless otherwise specified in t
19、he contract or purchase order, a sample shall be subjected to first article inspection (see 4.4 and 6.4). 3.4 Materials. Materials shall conform to the referenced specifications and the requirements specified herein, 3.4.1 Copper Base Alloy. The copper base alloys shall be roll polished, free from p
20、its, scale (including red oxide), dents, nicks, cracks, scratches, segregations, and foreign inclusions that will not be removed in later processing. applicable copper base alloy shall be as specified in table I. When tested as specified in 4.5.1, the chemical composition of the 3 Provided by IHSNot
21、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-_I_ - -_I_ MIL-R-14647 4 7777906 0377354 Nickel Lead Iron Manga- I/ (max- (max- nese zinc imum) imum) (max- imum) Alloy Copper - Red Brass 84.0-86. O O5 .O5 Remainder Gilding Metal 94.0-96.0 o3 05 Remainder Free Cutting
22、60.0-63.0 2.50- Remainder Bronze 89.0-91 .O .O5 .O5 Remainder Nickel Silver 63.0-66.5 16.5-19.5 .IO .25 .50 Remainder Brass 3.70 MIL-R-14649 Others (max- imum) .I5 . I3 o 13 TABLE I. Chemical composition of copper base alloy. 3.4.2 - Yarn. The yarn shall be a continuous filament, bright regenerated
23、cellulose rayon of the viscose or cuprammonium type with not less than 20 filaments for the single yarn. The pattern of the ribbon shall be as specified on applicable specification sheet. The warp and filling yarn shall be 5O/2 denier. 3.4.3 Color. The individual colors of the yarns used in the ribb
24、on shall conform tothe cable numbers designated by The Color Association of the United State, and specified in individual specification sheets, (see 2.1). sulfur dyes and dyes containing elementary sulfur or compounds capable of oxidication to sulfuric acid is prohibited, The use of 3.4.3.1 Colorfas
25、tness. The colors shall show fastness to crocking, wet dry cleaning, water and light equal to or better than the standard sample when tested as specj.fied in 4.5.1.1. 3.4.4 Matching. The color shall match the standard sample when viewed under filtered tungsten lamps which approximate artificial dayl
26、ight having a corre- lated color temperature of 7000 plus or minus 500 K, with illumination of 100 plus or minus 20 foot candles, and shall be a good match to the sample under incandescent lamplight at 2300 plus or minus 100 K. be equal to the standards established in the DOD Standard Color Card of
27、Official Standardized Shades for Heraldic Yarns for Embroidery and Ribbons, 1974 The degree of luster shall 3.4.5 Color pattern. The color pattern for the ribbon layout shall be as specified on the applicable specification sheet. have a taffeta or plain weave with no selvage, be as shown on the appl
28、icable specification sheet. 3.4.6 Weave. Except for the Medal of Honor Ribbon, all other ribbon shall The Medal of Honor Ribbon shall C 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-a I I O a MIL-R-19697 89 H 7977706 0377155 T MIL-R-14649 3.4.7 T
29、hread for tie. Unless a ribbon tie is specified, the thread for the tie shall be polyester or polyester/cotton, 300 denier and shall be an acceptable color match as indicated on the applicable specification sheet. 3.5 Metal forms. The metal forming the cup of the rosettes shall be made of 70/30 soft
30、 brass to be not more than .O10 inch thick and not less than .0095, draw quality. The cup shall conform to the design and measurements for the type indicated on specification sheet and shown on drawing B-6-7. punched on center to be .O35 plus or minus .O03 inch diameter. A hole 3.5.1 Backing disc. T
31、he metal backing disc, (see B-6-7) is to be any type half/hard brass ,025 plus or minus .O05 inch thick. A .O35 plus or minus .O03 inch diameter hole shall be punched on center. 3.5.2 Prong and clutches. The prong shall be a standard commercial post 3/8 inch in length and 0.045 plus or minus .O03 in
32、ch in diameter. Prong and clutches shall be in accordance with drawing B-12-13. 3.6 Design. The design of the finished each rosette shall conform to the pattern as shown on the individual specification sheet (see supplement 1). 3.7 Construction. The ribbon for the cup specified in the applicable spe
33、cification sheet shall bs used to cover and line the metal form of the rosette. The ribbon shall be smoothly and securely cemented in place with a water insolvable adhesive. After the disc is in place and the post set the rose ribbon shall be pleated, tied in the center, (see 3.4.7) then opened to f
34、orm a double fan and cemented within the cup with a water insolvable adhesive. 3.7.1 Tinting edges. When applicable, the edges that have warp yarn exposed other than the required shade shall be colored with an opaque, water proof ink to match the base color of the ribbon. 3.8 Workmanship. The finish
35、ed rosette shall conform to the quality end grade of product established by this specification. shall not exceed the acceptable quality levels established by this specifi- cation. The occurrence of defects 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection, Unless otherwise specified
36、in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use-his own or any other facilities suitable for the performance of the inspect
37、ion require- ments specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspection set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 5 Provided by I
38、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I I - MIL-R-I4649 84 9999906 0379I5b I W MIL-R-14649 4.1.1 Responsibility for conipliance. All items must meet all requirements of sections 3 and 5. become a part of the contractors overall inspection system ot. qua
39、lity program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of assuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. authorize submission of known defect
40、ive material, either indicated or actual, nor does it commit the Government to acceptance of defective material. The inspection set forth in this specification shall Sampling in quality conformance does not 4.1.2 Certificate of compliance. When certificates of compliance are sub- mitted, the Governm
41、ent reserves the right to check test such items to determine the validity of the certification. 4.2 Classification of inspections. The inspection requirements specified herein are classified as follows: a. First article inspection (see 4.4). b , Quality conformance inspection ( see 4 .5). 4.3 Inspec
42、tion conditions. Unless otherwise specified, all inspections shall be performed in accordance with the test conditions specified in applicable test method document or applicable paragraph(s) in the specification. 4.4 First article inspection, Inspection and testing of the first article sample shall.
43、 be made on a completely finished rosettes for all provisions of this specification applicable to the end product examination and tests. 4.5 Quality conformance inspection. Inspection shall be in accordance with provisions set forth in MIL-STD-105, except where otherwise indicated. 4.5.1 Quality ass
44、urance inspection. Inspection shall be in accordance with the provisionsset forth in MIL-STD-105, except when otherwise specified hereafter. 4.5.1.1 Testing of components. In addition to the quality assurance provisions of subsidiary specifications, testing shall be in accordance with test methods s
45、pecified in FED-STD-191 or FED-STD-151 where applicable, and as specified in table II. When the data in the tlnumber of determinations per unit of product“ and the Vesults reported ast1 columns are not specified in table II they shall be as required by the referenced test method. The sample size sha
46、ll be in accordance with inspection level L-I of Standard MIL-STD-IO5 and the acceptable quality level (AQL) shall be 6.5 defects per 100 units. The unit of product shall be one yard of the ribbon and the lot size shall be expressed in units of one yard. 6 Provided by IHSNot for ResaleNo reproductio
47、n or networking permitted without license from IHS-,-,-hnponent Fdeterm )er s/u - :up Results reported as Nearest 0.1% for each element To nearest denier tibbon yarn Rdhesive MIL-R-34bq7 84 977770b 0377357 3 MIL-R- 34649 TABLE II. CompohBht tests. Characteristic Material ident Material ident Presenc
48、e of sulfur Crocking Wet-dry Water Light cleaning Water insolv- able type - - _, Rqm t para 3.5 3.4 - I/ 3.4.3 3.4.3.1 3.4.3.1 3.4.3.1 3.4.3.1 3.7 - - _- Test method 111 - 1500 or 1520 4/3 - I/ 565 1 5622 5630 5660 I/ - I (Pass or fail - I- - II Unless otherwise specified a contractors certification
49、 of compliance may be accepted as evidence of conformance. 4.5.2 Test. 4.5.2.1 Chemical composition test. Chemical composition shall be determined in accordance with test method Ill of FED-STD-151. Results shall be evaluated to determine compliance with the requirements specified in 4.5.1.1. 4.5.3 Inspection of the end item. 4.5.3.1 Visual examination of the end item. Defects found during this exam- ination shall be classified in accordance with 4.
