1、Ip_ MIL-R-44375 4 9999906 OLi03972 T a MIL-R-443 75 30 June 1989 MILITARY SPECIFICATION REPAIR KIT, SKI, SNOW AND ICE TRAVERSING EQUIPMENT (SITE) This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers a bag c
2、ontaining materials, tools, and parts for use in the repair of skis and ski poles. 2. APPLICABLE DOCJMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifi- cations, standards, and handbooks form a part of this document to the extent specified herein. U
3、nless otherwise speciied, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standrds (DODISS) and supplement thereto, cited in the O solicitation (see 6.2). I 1 Beneficial comments (recommendations, additions, deletions) and any pert
4、inent data which may be ofuse in improving this document should be addressed to: U.S. Army Natick Research, Development, and Engineering Center, Natick, MA 01760-5014 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by
5、letter. I I AMSC N/A FSC 8465 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. - THIS DOCUMENT CONTAINS /b PAGES. y - - - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SPECIFICATIONS FEDERAL A-A-1043 P-C-45 1 QQ-W-4
6、6 1 DDD-L-20 GGG-D-67 1 GGG-P-47 1 GGG-S-12 1 PPP-B-566 PPP-B-636 PPP-B-676 MILITARY MIL-P-116 MIL-B-121 MIL-L-35078 STANDARDS FEDERAL FED-STD-751 MILITARY MIL-STD-105 MIL-STD-129 MIL-STD-147 MIL-STD-731 - Steel Wool - Coated Abrasive, Cloth, Aluminum Oxide or Silicone Carbide - Wire, Steel, Carbon
7、(Round, Bare, and Coated) - Label: For Clothing, Equipage, and Tentage, -*-Drill; Hand, and Push - Pliers; Pliers, Slip Joint - Screwdriver and Screw Starter, Hand - Boxes, Folding, Paperboard - Boxes, Shipping, Fiberboard - Boxes, Set Up (General Use) - Preservation Method Of - Barrier Material, Gr
8、easeproofed Waterproofed, Flexible - Loads, Unit: Preparation of Semiperishable Subsistence Items; Clothing, Personal Equipment and Equipage; General Specification For - Stitches, Seams, and Stitchings - Sampling Procedures and Tables for Inspection - Marking for Shipment and Storage - Palletized Un
9、it Loads - Quality of Wood Members for Containers and Pallets by Attributes (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Naval Publications and Forms Center, (ATTN: NPODS), 5801 Tabor Avenue, Philadelphia, PA 19120-5099.)
10、 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein, Unless otherwise specified, the issues are those cited in the solicitation. 2 Provided by IHSNot for Resale
11、No reproduction or networking permitted without license from IHS-,-,-. MIL-R-44375 DRAWINGS U. S. ARMY NATICK - 2-2-238 2-10-85 - 2-10-86 - - 2-10- 108 2-10-111 - 2-10-1 19 - RESEARCH, DEVELOPMENTy k!D ENGINEERING CENTER Repair Kit, Ski, Military, All Terrain; File Bag, Repair Kit, Ski, Military, Al
12、l Terrain; Bag, Repair Kit, Ski, Military, All Terrain; Hand Grip Assembly Basket Assembly Plug, Expansion and Scraper Assembly and Illustration Details and Sections . (Copies of drawings are available from the U.S. Army Natick Research, Development, and Engineering Center, Natick, MA 01760-5014.) 2
13、.2 Non-Government publications, The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the is
14、sues of documents not listed in the DODICS are the issues of the documents cited in the solicitation (see 6.2). AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D 3951 - Standard Practice for Commercial Packaging E 18 - Rockwell Hardness Test (Application for copies should be addressed to the Ameri
15、can Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1187.) (Non-Government standards and other publications are normally available from the organizations that prepare or distribute the documents. These documents also may be available in or through librakies or other infor
16、mational services.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been ob
17、tained. 3. REQUIREMENTS 3.1 First article. When specified (see 6.21, a sample shall be subjected to first article inspection (see 6.3) in accordance with 4.3. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- I_ - - MIL-R-44375 84 977770b 0403775 5
18、material or source. TABLE I. Kit components Item No. Description Sour ce Quantity 1 Bag, repair kit, ski,. military, all terrain 2 Scraper 3 Fi le 4- Handgr ip embly 5 Plug, expansion 6 Basket assembly 7 Pliers, slip joint, straight nose combination jaw w/cutter, regular, 6 inches 8 Screwdriver, fla
19、t tip, close quarter, I 1/2 inch nominal length 9 Wire, seizing, 0.048 inch diameter, 1/4 pound 10 11 12 Drill, hand and push Cloth, abrasive, aluminum oxide Tape, filament, reinforced 2 inch by 5 yards long, white translucent color, cold temperature capability Drawing 2-10-85 Draw i ng 2-2-238. Dra
20、wing 2-2-238 Drawing 2-10-108 Drawing 2-10-1 19 Drawing 2-10-111 GGG-P-471, type II, class 2, style A GGG-S-121, type I, class 3 QQ-W-46 1, carbon steel No. 1006, finish 1, annea led GGG-D-671, type IV, class 1 P-C-451, type I, class I, 120 grit, 6 by 11 inch sheets (see 6.4) - i/ 1 1 1 2 6 2 1 1 1
21、spool 1 2 1 roll 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-44375 4 M 9999906 0403976 7 M - _ -= MIL-R-44375 TABLE I. Kit components - Continued Item No. Description Source Quant i ty 13 Polyethylene repair candle, clear color 14 Steel w
22、ool 15 Screwdr iver-Pozidr iv number 3 point, 8-inch nominal length Screws lat head with PozidrivB 16 recess, standard number 12 HB type, 16 mm long 17 Screws flat head with PozidrivB recess, standard number 12AB type, 14 mm long 18 Structural adhesive kit, 4 ounce 19 Adhesive, climbing skin 3 1/2 f
23、luid ounces (see 6.4) - i/ A-A-1 043 type III, No. 1 medium (see 6.4) (see 6.4) (see 6.4) Urethane expoxy, P/N 3535 (see 6.4) - i/ (see 6.4) - i/ 2 1/8 pound 1 12 12 1 1 - i/ Prior to inclusion as a component, the contractor shall submit any substituted “or equal“ item, together with supporting data
24、 to the contracting officer for subsequent approval or disapproval by the responsible military agency. . 3.3 Design and construction. The design and construction of the repair kit shall conform to the drawings listed in section 2 and to the requirements specified herein. 3.3.1 Scraper. The scraper s
25、hall meet the hardness requirement indicated on Drawing 2-2-238 when tested as specified in 4.4.5. 3.3.2 Stitches, seams, and stitching, All stitching shall conform to type 301 of FED-STD-751. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-4
26、4375 84 M 7777706 0403777 7 MIL-R-44375 33.2.1 Automatic stitching. Automatic stitching machines may be used to perform any of the required stitch patterns provided the requirements for stitch I pattern, stitches per inch, and size and type of thread are met, and at least three tying, overlapping, o
27、r backstitchec are used to secure the ends of stitching. 3.3.2.2 Lubrication of thread. There shall be no lubrication of the thread by any means prior to or during sewing (see 4.4.1.1). : 3.3.2.3 Type 301 stitching. Ends of all stitching shall be backstitched or overstitched 1/2 inch minimum except
28、when caught in other stitching or turned under in a hem. Thread tension shall he maintained- so that there will he no loose bobbin or top thread or excessively tight stitching resulting in puckering of the materials sewn. The lock shall be embedded in the materials sewn. 3.3.2.3.1 Repairs of type 30
29、1 stitching. Repairs of type 3Q1 stitching shall be as- follows: a. When thread breaks or bobbin run-outs occur during stitching, the stitching shall be repaired by restarting the stitching a minimum of 1 inch back of the end of stitching. b. Thread breaks or two or.more consecutive skipped or run-o
30、ff stitches noted during inspection of the item (in-process or end item) shall. be repaired by overstitching. The stitching shall start a minimum of 1 inch in back of the defective area (1/2 inch on box, box-x, and W-W stitching) and continue a minimum of 1 inch beyond the defective area onto the ex
31、isting stitching. Loose or-excessively tight stitching shall be repaired by removing the defective stitching, without damaging the materials, and restitching in the required manner. (Whenmaking the abave repairs in a. and b. above, the ends of the stitching are not required to be backstitched.) 3.3.
32、2.4 Thread ends. All thread ends that are visible on the finished item shall be trimmed to a length of not more than 1/4 inch. 3.4 Marking. Marking for the bag shall conform to the requirements of type IV, class 5 of DDD-L-20. The marking shall be placed OE the inside of the pocket body (item 4 of D
33、rawing 2-10-86) so as to be readable when the bag is opened. 3.4.1 Location marks. Location marks shall not be drilled. Printed markings for component location shall not be more than 1/32 inch wide. 3.5 Repairs. Repairs such as mends, darns, patches, or splices are not permitted on the bag. 6 Provid
34、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-44375 - 4 9979706 OY0377 O - _ MIL-R-443 75 3.6 Replacement of defective components. During the- spreading, cutting, and manufacturing process, components of the bag having material defects or damages t
35、hat are classified as defects in 4.4.3 shall be removed from production and replaced with nondefective and properly matched components. 3.7 Finish. All components shall be finished in accordance with the applicable requirements of referenced documents. Commercial items shall be finished in accordanc
36、e with the manufacturers standard practice, 3.8 Workmanship. The end item shall conform to the quality of product established by this specification. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspectj.on. Unless otherwise specified in the contract or purchase order, the contractor is res
37、ponsible for the performance of all inspection requirements (examinations and tests) as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified here
38、in, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in this specification where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements. 4.1.1 Responsibility for compliance. All items
39、 shall meet all requirements of sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility
40、 of ensuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling inspection, as part of manufacturing operations, is an acceptable practice to ascertain conformance to requirements, however, this does not authorize submissio
41、n of known defective material, either indicated or actual, nor does it commit the Government to accept defective material. 4.1.2 Responsibility for dimensional requirements, Unless otherwise specified in the contract or purchase order, the contractor is responsible for ensuring that all specified di
42、mensions have been met. When dimensions cannot be examined on the end item, inspection shall be made at any point, or at all points in the manufacturing process necessary to ensure compliance with all dimensional requirenients. 4.1.3 Certificates of compliance. When certificates of compliance are su
43、bmitted, the Government reserves the right to inspect such items to determine the validity of the certification. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-44375 4.2 Classification of inspections. The inspection requirements specified he
44、rein are classified as follows: a. b. Quality conformance inspection (see 4.4). First article inspection (see 4.3). 4.3 First article inspection. When a first article is required (see 3.1 and 6.2), it shall be examined for the defects specified in 4.4.3 and 4.4.4. 4.4 Quality conformance inspection.
45、 Unless otherwise specified, sampling for inspection shall be performed in accordance with MIL-STD-105. 4.4.1 Component and material inspection, In accordance with 4.1, components and materials shall be inspected in accordance with all the requirements of refer.enced documents unless otherwise exclu
46、ded, amended, modified, or qualified in this specification or applicable purchase document. 4.4.1.1 Component and material certification. A certificate of compliance may be acceptable as evidence that the thread has not been lubricated during sewing as specified in 3.3.2.2. 4.4.2 In-process inspecti
47、on. Inspection of subassemblies shall be made to ascertain that construction details which cannot be examined in the finished product are in accordance with Drawings 2-10-85 and 2-10-86. The Government reserves the right to exclude from consideration for acceptance, any material or service for which
48、 in-process inspection has indicated nonconformance. L 4.4.3 End item visual examination. The end items shall be examined for the defects listed in table II. The lot size shall be expressed in units of repair kits. The sample unit shall be one repair kit. The inspection level shall be II (see 6.5).
49、TABLE II. End item visual defects Examine Defect Classification Major Minor AB Fabric Cut, tear, or hole 101 Broken or missing yarns; multiple floats clearly visible at normal inspection distance (approximately 3 feet) Not color specified 201 202 , e Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-Lt4375 4 7777906 0403980 7 W - - -
