1、-. MIL-R-52453C 38 m 9999906 0239602 T m henef icial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: US Army Mobility Equipment Research and Development Command, ATTN: DRDME-DS , Fort Belvoir, VA 22060 by
2、using the self-addressed Standardization Document improvement Proposal (DD Form 1426) appearing at the end of this document or by MIL-R-5 245 3C( ME) 31 May 1983 SUPERSEDING MIL-R-5245 3B (ME) 14 April 1975 MILITARY SPECIFICAT ION ROLLER, MOTORIZED, PNEUMATIC TIRED: AIRMOBILE, 9 WHEEL This specifica
3、tion is approved for use by the Mobility Equipment Research and Development Command, Department of the Army, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers a pneumatic-tired, self-propelled, diesel-engine-driven ro
4、ller, Swheel, capable of being airlifted by military helicopt er. 2. APPLICABLE DOCUMENTS 2.1 Government document s. 2.1.1 Specifications and standards. Unless otherwise .specified (see 6.21, the following specifications and standards of the issue listed in that issue of the Department of Defense In
5、ex of Specifications and Standards (DoDISS) specified in the solicitation, form a part of this specification to the extent spec if ied herein. SPECIFICATIONS FEDERAL VV-F-800 - Lubricating Oil, General Purpose, Preservative, (Water-Displacing , Low Temperature) . li et ter. I FSC 3895 Provided by IH
6、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-52453C 38 m 4940b-b3 I m MI La- 5 245 3C( ME MLLITARY MIL-V-17 3 MIL-P-514 MIL-2-7 04 MI L-L- 21 O 4 MZL-R- 30 75 MI L-A-8 421 MIL-G-1 O9 24 MIL-G-23827 MIL-C-46168 MIL-B-4617 6 Varnish, Moistureand-Fungus-Resi
7、stant , ( for Treatment of Communications, Electronic, and Associated Equipment) . Plat es, Ident if icat ion, Instruct ion and Marking, Blank. .a Treatment and Painting of Materiel. Lubricating Oil, Internal Combustion Engine, Tactical Service. Roller, Motorized, Road Diesel-or-Gasoline Driven, Pac
8、kaging of. Air Transportability Requirement, General Specification. Grease, Automotive and Artillery. Grease Aircraft and Instrument, Gear and Actuator Screw. Coating, Aliphatic Polyurethane, Chemical Agent Resistant. Brake Fluid, Silicone, Automotive All Weather, Operational and Preservative. STAND
9、ARDS FEDERAL F ED-STD-H28 - Screw-Thread Standards For Federal Services. MILITARY MI L-STD -130 MIL-CTD-20 9 MIL-STD-6 42 MIL-STD-889 - Identification Marking of US Military - Slinging and Tiedown Provision For Lifting - Identification Marking of Combat and Tactical - Dissimilar Metals. Property . a
10、nd Tying Down Military Equipment. Transport Vehicles. (Copies of specifications and standards, required. by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting oeficer.1 2.1.2 Other Government documents, dra
11、wings, and publications. The following other Government documents, drawings, and publications form a part of this specification to the extent specified herein. ENVIRONMENTAL PKOTECTION AGENCY ( EPA) 40 CFR 86 - Control of Air Pollution from New Motor Vehicles and New Motor Vehicle Engines. 2 Provide
12、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-52Ll53C 38 7779906 0237604 3 MIL-R-5 2453C( ME) (AppIication for copies should be addressed to the Superintendent for Documents, US Government Printing Office, Washington, DC 20402. ) DEPARTMENT OF LABOR
13、 (DOL) 29 CFR 1926 - Occupational Safety and Health Administration (OSHA) Standards for Construction Jobs. DEPARTMENT OF TRANSPORTATION (DOT) FMVSS - No. 116 - Motor Vehicle Brake Fluids. The Code of Federal Regulations (CFR) and the Federal Register (FR) are for sale on a subscription basis by the
14、Superintendent of Documents, US Government Printing Office, Washington, DC 20402. When indicated, reprints of certain regulations may be obtained from the Federal agency responsible for issuance thereof. 2.2 Other publications. The following document(s) form a part of this specification to the exten
15、t specified herein. The issues of the documents which are indicated as DoD adopted shall be the issue listed in the current DoDISS and the supplement thereto, if applicable. AMERICAN NATIONAL STANDARDS INSTITUTE, INC. (ANSI) ANSI 235.1 - Industrial Accident Prevention Signs, Specification For. (Appl
16、ication for copies should be addressed to the American National Standards Institute, Inc. , 1430 Broadway New York, NY 10018. AMERICAN SOCIETY FOR TESTING AND MATERIAIS (ASTM) ASTM D1557 - Moisture-Density Relations of Soils using 10-lb (4.5 kg) Ramer and 18-in. (45.7 mm) Drop, Methods of Test For.
17、(Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) NATIONAL ASSOCIATION OF METAL NAME PLATE MANUFACTURERS, LNC. (NAME) Metal Name Plate Industry S tandards and Practices. (Application for copies should be addresse
18、d to the National Association of Metal Name Plate Manufacturers, Inc., 1000 Vermont Avenue, NW, Washington, DC 20005. SOCIETY OF AUTOMOTIVE ENGINEERS ( SAE) SAE HANDBOOK (Application for copies should be addressed to the Society of Automotive Engineers, 400 Commonwealth Drive, Warrendale, PA 15096.)
19、 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-52453C 38 99999Ob 02L9b055pi MI L-R- 5 245 3C( ME TIRE AND RIM ASSOCIATION, INC. T adjustment of the brake system and electrical system; inflation of tires; and complete lubrication of the roll
20、er with the types and grades of lubricant recommended. 3.23 Oil sampling valve. An oil sampling valve shall be provided on the Th valve shall be manually operated and shall automatically close engine. after release. will not contaminate the sample. covered with a captive chained cap conforming to SA
21、E 5514. located in such a way as to insure that personnel will not be exposed to danger when taking oil samples with the engine running. shall be such that when samples are taken, it shall be a true representation of oil that ia flowing while the engine is running. It shall be made of material resis
22、tant to corrosion.such that it The discharge port of the valve shall be The valve shall be The location of the oil tap 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-R-52453C 38 7779706 0219b12 2 N 3.24 Treatment and painting. The parts of th
23、e roller normally painted shall be cleaned, treated, and painted in accordance with MIL-T-704. specified (see 6.2), the final coat shall be in accordance with MIL-C-46168. Unless otherwise 3.25 Data plates. Data plates shall be applied to the equipment on metal plates in accordance with the “Metal N
24、ame Plate Industry Standards and Practices“, Manufacturers, Inc., (NAME). Identification and shipping data plates shall be of material in accordance with MIL-P-514, Composition C. The plates shall be secured to each end item in accordance with the NAME Standards and Practices. as published by the Na
25、tional Association of Metal Name Plate 3.25.1 Identification. The equipment shall be identified in accordance with MIL-STD-130 and MIL-P-514. complete equipment under contract and shall not be prior to date of Government acceptance. The date of the delivery shall be that of the 3.25.2 Instruction pl
26、ates. The equipment shall be equipped with instruction plates, decals, or diagrams, including warnings and cautions, describing any special or important procedures to be followed in assembling, operating, or servicing. The safety, warning, caution, and notice plates shall be in accordance with ANSI
27、235.1 and compatible with the space available. 3.25.3 Lifting and tiedown instruction plates. Instructions for the use of the attachments or procedures shall be included on a metal plate permanently affixed to the equipment. together with the center of gravity. The plate shall include a silhouette o
28、f the item 3,25.4 Shipping data plates. Shipping data plates for each roller shall be furnished and shall show the silhouette of the roller indicating the location and capacity of t iedown provisions, slinging provision, extraction provisions, suspension provisions, the center of balance and shippin
29、g weight. conform to MIL-P-514, Type III or contractors standard plates subject to the approval of the contracting officer. side of the roller and shall show the locations as viewed from the left side. The plate shall be located in conspicuous protected locations. be permanently attached. Plates sha
30、ll The plates shall be attached to the left All plates shall 3.26 Marking. Marking and registration shall be in accordance with MIL-STD-642. Color shall be lusterless black. 3.27 Toolbox. A lockable storage compartment(s) or toolbox of sufficient size to hold all tools and equipment required for ope
31、ration and operator maintenance shall be provided. 3.28 Workmanship. 3.28.1 Steel fabrication. Steel used in the fabrication of the roller shall be free from kinks and sharp bends. Steel plate shall not be warped. The straightening of material shall be done by methods that will not cause injury to t
32、he metal. to remove ash and cooling checks. with metal dies or fixtures in order to insure uniformity of size and shape. Burned surfaces of flame-cut materials shall be ground or machined All bends of a major character shall be made 11 Provided by IHSNot for ResaleNo reproduction or networking permi
33、tted without license from IHS-,-,-MIL-R-52453C 38 7777qOb 0219613 4 W I 4. QUALITY ASSURANCE PROVISIONS MIL-R-5 2453C( ME) 4. 1 Responsibility for inspection. Unless otherwise specified in the contract, the contractor is responsible for the performance of all inspection requirements as specified her
34、ein. contract, the contractor may use his own or any other facilities suitable for performance of the inspection requirements specified herein, unless disapproved by the Government. inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services
35、 conform to prescribed requirements . Except as otherwise specified in the The Government reserves the right to perform any of the I 3.28.2 )olted connections. Boltholes shall be accurately punched or drilled and shall have the burrs removed. Washer or lockwashers shall be provided and all bolts, nu
36、ts, and screws shall be tight. 3.28.3 Riveted connections, Rivet holes shall be accurately punched or drilled and shall have the burrs removed. Rivets shall completely fill the holes. contact with the surface of the member, Rivet heads shall be full, concentric with the rive; hol. the operators stat
37、ion, a noise hazard caution sign per MIL-STD-1474 shall be permanently affixed to the equipment in the operators compartment. dB(A) contour should be defined. stenciled on the equipment: in a conspicuous location with 3/4 inch letters stating: “Hearing protection required within X feet from this equ
38、ipment“. The 85 The noise hazard zone shall be clearly Custodians : Army - ME User activity: Army - AT r9- us. GOVERNMENT PRINTING OFFICE: i 93-1305-034/3107 18 Preparing activity: Army - ME Project 3895-Al92 + Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
