1、- MIL-S-LL23E 35 W 99999Ob 0242902 5 W M.IL-S-ll23E 25 September i968 SUPERSEDING MU;-S-1123 i5 March 1966 MILITARY SPECIFICATION SHOE REPAIR SHOP, EQIIE“T This specification is mandatory for use by.all Departments and Agencias of the Department of Defense. 1. SCOPE 1.1 Scope.- This specification co
2、vers shoe repair shop equipment. * 1.2 Classification.- Shoe repair shop equipment shall consist of the following types and Type1 .- Size A - Size B - TypeII - TypeIV - me v - TypeVI - Ty-peVII - Ty-pe VI11 - sizes of equipment as specified (see 6.2) : Shoe finishing machine 7 1/2 foot length 11 foo
3、t length Shoe stitching machine Shoe soling press, laminated Sewing machine, industrial shoe patching ( see 3.4.1 Skiving and beveling machine, shoe sole, hand operated Heel removing and heel reducing machine, hand operated Stand, cobblers last, with lasts, floor type and 3.10.4) 2. APFLICABLE DOCUM
4、ENTS * 2.1 The following documents, of the issue in effect on date of invitation for bids or request for proposal, form a part of this specification to the extent specified herein: SPECIFICATIONS FEDERAL CC-M-636 - Motors, Alternating Current, (Fractional Horsepower). KK-B-211 - Belting; Round, Leat
5、her. 00- s-256 - Sewing Machines, Industrial. ni-P-664 . - Primer, Coating, Synthetic, Rust Inhibiting, Lacquer Resisting. Paper). MMM-A-O - Adhesive, Water Resistant (For Sealing Waterproofed PPP-B-601 - Boxes, Wood, Cle.ated-Plywood. FSC 3520 i I I - G Provided by IHSNot for ResaleNo reproduction
6、or networking permitted without license from IHS-,-,-MIL-S-LL23E 35 M 9977906 02L12903 7 PPP-B-621 - Boxes, Wood, Nailed and Lock-Corner. PPP-B-636 - Box, Fiberboard. PPP-B-1055 - Barrier Material, Waterproofed, Flexible. PPP-F-320 - Fiberboard; Corrugated and Solid, Sheet Stock PPP- T- 45 - Tape, G
7、ummed, Paper, Reinforced and Plain, for (Container Grade), and Cut Shapes. Sealing and Securing. for Packaging and Sealing. - . PPP-T-60 - Tape: Pressure-Sensitive Adhesive, Waterproof, MILITAFY MIL-C-104 - Crates, Wood; Lumber and Plywood Sheathed, Nailed MIL-P- - Preservation, Methods Of. MIL-B-12
8、1 - Barrier Material, Greaseproofed, Waterproofed, MIL-L-10547 - Liners, Case and Sheet, Overwrap; Water- MIL-E-15090 - Enamel, Equipment, Light Gray (Formula No. 11). and Bolted. Flexible. Vaporproof or Waterproof, Flexible. STANDAIIDS FEDERAL Fed. Std. No. 751 - Stitches, Seams, and Stitchings. MI
9、LITARY MIL-S”D-lO5 - Sampling Procedures and Tables for Inspection by MIL-STD-129 - Marking for Shipment and Storage. MIL-STD-130 - Identification Marking of U. S. Military Property. MIL- STD-461 - Electromagnetic Interference Characteristics, Requirements for Equipment. MIL-STD-462 - Electromagneti
10、c Interference Characteristics, Measurement Of. Attributes. (Copies of specifications and standards required by suppliers in connection with specific procurement functions should be obtained from the procuring agency or as directed by the contracting officer.) * 2.2 Other publications.- The followin
11、g documents form a part of this specification to the extent specified herein. Unless otherwise indicated, the issue in effect on date of invitation for bids or request for proposal shall apply. 9 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-
12、S-1123 UNDERWRITERS LABORATORIES, INC . (a) Standard No. 1 Standard No. 4 Standard No. 6 Standard No. 44 Standard No. 62 Standard No. 83 Standard No. 514 Standard No. 797 Conduit, Flexible Steel. Armored Cable, Conduit, Rigid Metallic. Wire and Cables, Rubber-Insulated. Flexible Cord and Fixture Wir
13、e. Wire, Thermop1asti.c-Insulated. Outlet Boxes and Fittings. Electrical Metallic Tubing. (Application for copies should be addressed to the Underwriters Laboratories, Inc . , 207 East Ohio Street, Chicago, Illinois 60611; Walt Whitman Road, Melville, Long Island, N. Y. 11749; or 1655 Scott Boulevar
14、d, Santa Clara, California 95050, ) NATIONAL! FIFUI PROTECTION ASSOCIATION (NFPA) Standard No. 70 (1965)- National Electrical Code. (Application for copies should be addressed to the National Fire Protection Association, 60 Batterymarch Street, Boston, Massachusetts 02110. ) (Technical society and t
15、echnical association specifications and standards are generally available for reference from libraries. tributed among technical groups and using Federal agencies .) They are also dis- 3. RFQUIREMENTS 3.1 First article.- Unless otherwise specified (see 6.2), before pro- duction is commenced, a sampl
16、e of the finished commodity procured under this specification shall be submitted or made available to the contracting officer or his authorized representative for approval in accordance with 4.2. The approval of the preproduction sample authorizes the commencement of pro- duction but does not reliev
17、e the supplier of responsibility for compliance with all provisions of this specification. The preproduction sample shall be manufactured in the same facilities to be used for the manufacture of the production items. * 3.2 Standard products.- Each item of equipment, including accessories, shall be a
18、 current standard product of an established manufacturer, except for such deviations from the manufacturers commercial product as may be required by the specification. * 3.3 Standards compliance.- Electrical components shall comply with the following L standards : fittings-Standard No. 514; armored
19、cable-Standard No. 4; flexible cord and fixture wire-Standard No. 62; thermo-plastic- insulated wire-Standard No. 83; rubber insulated wire-Standard No. 44; and conduit or tubing-Standards No. 1, 6, or 797, as applicable. The installation of electrical components for each machine shall conform to NF
20、PA Standard NO. 70, the “National Electrical Code“. 3 I ! Y- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-LL23E 35 7777706 0242705 O W MIL- S-1123 * 3.3.1 Certification.- Prior to approval of the first article, or if none is submitted, prior
21、 to approval of the first shipment, the supplier shall submit satisfactory evidence to the contracting officer or his authorized representative that the electrical components he proposes to furnish under this specification meet the requirements of UL standards, as applicable. * 3.3.1.1 L and “PA.- A
22、cceptable evidence of meeting the applicable requirements of specified UL standards shall be the UL label or a photo- static copy of the L listing card for the components being offered or a certified test report from a recognized independent testing laboratory acceptable to the Government, indicatin
23、g that the electrical materials- and components offered have been tested and conform to applicable UL standards. Standard No. 70-1965 shall be the manufacturers certified statement that the installation of electrical components conform to applicable requirements. Acceptable evidence of meeting the r
24、equirements of NFPA * 3.4 Materials and components.- Materials and components shall conform to the applicable referenced specifications, standards, and requirements specified hereinafter. When materials are not definitely specified, they shall be of the type and quality used by the manufacturer in h
25、is standard commercial product. 3.4.1 Electrical equipment .- The machines shall be furnished complete with motors, driving mechanism, manual starters, heaters and all other components, as applicable, required to complete the assembly and meet the test in 4.5.1. Unless otherwise specified (see 6.2)
26、types I and II, electrically operated machines, shall be suitable for operation on a 3 phase, 4 wire, 120/208 volt, 60 cycle, alternating current (a.c.) power source. 6.2), it shall be suitable for operation on a single phase, 11-5 volt, 60 cycle, a.c. power source. When an electrically operated typ
27、e V machine is specified (see * 3.4.1.1 Motors.- Motors shall conform to CC-M-636. Motor inclosure shall be either drip proof or splash proof. in 40 Centigrade (C.) ambient without exceeding 40 C. allowable temperature rise. All motors shall conform to class A insulation requirements. The speed shal
28、l be constant speed type. squirrel cage for 3-phase supply and squirrel cage split phase or capacitor for single phase supply. They shall be continuous duty Windings for a.c. motors shall be Winding for d.c. motors shall be shunt. 3.4.1.1.1 Horsepower.- Rated horsepower shall be the same as motors f
29、urnished by the supplier in his regular commercial machine. 3.4.1.2 Motor starters. - Motor starters shall be across-the-line heavy- duty type, with push button or toggle switch, to completely make or break all electrical connections to the motor. with overload protection, the starters shall be furn
30、ished with a built-in overload protective device. conform to a commerical type I Inclosure. When the machine motor is not equipped The starter inclosure shall be metal and shall 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-S-LL23E 35 W 9777
31、906 0242906 2 MIL-S-1123E * 3.4.2 Electromagnetic compatibility. - Equipment procured for Army shall be designed and equipped for electromagnetic compatibility in accordance with Class IIB of MIL-STD-461 (see 4.5.2.) equipment procured for Air Force shall be in accordance with Class IIB of MIL-STD-4
32、61 (see 4.5.2). When specified (see 6.2), 3.5 Design and construction.- All moving parts shall show no evidence of undue vibration, noise, or overheating of bearings, and the starting and stopping device shall operate smoothly and positively when subjected to the operational test specified in 4.5.1.
33、 3.5.1 Lubrication.- Oil or grease fittings shall be incorporated in accessible locations for use in lubricating bearings, as required. Pressure oil lubrication shall not be used for motor bearings. 3.5.2 Clutches.- Clutches shall be engaged by a pedal conveniently located for operation frm. a stand
34、ing position. 3.5.3 Belt drives.- Machines furnished with belt drives shall be provided with means for adjusting belt tension. waterproofed leather conforming to KK-B-211. position rubber and fabric of the type normally furnished in commercial practice. Round belts shall be V-belts shall be com- 3.5
35、.4 Machin2 bases.- The base supports on all machines shall be of malleable iron, cast iron, or steel, and of rigid construction. Holes shall be provided not less than one-half inch diameter to receive anchor bolts, except as specified in 3.10.1. 3.5.5 Safety devices.- Exposed belts, shafts, pulleys,
36、 gears, and other moving parts hazardous to operators shall be fully inclosed and guarded in- so far as practicable, so as to prevent operator contacting same. shall be of malleable iron, steel, sheet metal, or wire mesh. All parts of the guard shall be rigid, and secured so as to be removable witho
37、ut dis- assembling operating parts of the machine. requiring frequent adjustment shall be hinged or shall be removable without the need for tools. Guards Guards fitted over parts * 3.5.6 Wiring.- Wiring shall comply with NFPA Std, No. 70. Wires shall be completely installed in flexible or rigid zinc
38、-coated conduit or shall be armored flexible cable. All connections shall be made between motors, starters, and switches. sufficient slack to prevent breakage due to vibration. Parts shall be installed on the machines with i * 3.6 Tools.- Tools and wrenches necessayy for the proper service, maintena
39、nce, and adjustment of the equipment shall be furnished where specified under detail requirements. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-LL23E 35 7777706 02Li2707 Li W MIL-S-1123E 3.7 Equipment manual.- The supplier shall furnish wi
40、th e.ach machine an equipment manual. Manual contents and distribution shall be as specified in the contract or order (see 6.2). 3.8 Identification plates .- Each machine shall bear an identification plate conforming to the requirements of MIL-STD-130. installed on and furnished as part of the machi
41、nery or equipment for which it is intended. The plate shall be 3.9 Finish.- The equipment shall be finished in accordance with the manufacturers regular commercial practice. Finish shall not be blistered, chipped, or peeled. 3 .lO Detailed requirements. - 3.10.1 Type I, shoe finishing machine.- The
42、finishing machine shall be a dustless, single unit model, electric motor driven. Power shall be trans- mitted from the electric motors to the attachments by means of V-belt drive. All shafts shall be balanced and quiet running in self-aligning bearings. The frame shall be of malleable iron or steel
43、and so fastened and braced to the leg that the assembled machine is rigid. The legs shall be of nialleable iron, cast iron, or steel with at least one 5/8 inch hole in each foot for anchor bolts, A hood shall be provided above the finisher shaft, the length of the machine. Each finishing machine sha
44、ll be pro- vided with a conveniently located rack to hold forepart cutters and the burnishing irons. 3.lO.l.l Suction system.- A suction system shall be incorporated in the machine and shall have a capacity sufficient to carry off all dust and leather particles produced during operation of the machi
45、ne. blower shall be connected to an independent electric motor and shall be provided with a separate “on“ and “off“ push button switch. collected by the suction system shall be exhausted into a conveniently located receptacle which may be detached for emptying or be so constructed as to be easily cl
46、eaned out. The suction The dust 3.10.1.2 Type I, size A.- In addition to requirements of 3.10.1 and The attachments shall be as tabulated in Table I 3.10.1.1, the machine with all attachments installed shall not exceed 7 1/2 feet in length. and mounted from left to right in the order listed. TABLE I
47、 - Type I, size A shoe finishing machine Quantity Item No. Nomenclature .Required 1 Cutter, forepart. 1 brush attachment. 1 2 Heel trimmer with shank sander and wire b Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-LL23E 35 H 9999qOb 0242908 b
48、 m MIL-S-1123E TABLE I - Type I, size A shoe finishing machine (contd) Quantity Item No. Nomenclature Required Grinder attachment 1 1 Scouring wheel, flat surface, 1-3/8 inch 3 4 Heel breaster . 5 width by 5 inch diameter (with metal protective edge when specified (see 6.2) ) . protective edge when
49、specified (see 6.2) ) . 1 6 Bottom sander 4-1/2 inch width. 1 7 Scouring wheel, flat surface, 1-3/8 inch width by 5 inch diameter (with metal 1 8 Brush, shank, 1-1/2 inch width by 8 inch diameter. 2 9 Iron, edge, sole and heel. 1 * 3.10.1.3 Type I, size B.- In addition to requirements of 3.10.1 and The attachments, unless otherwise specified (see 6.2), 3.lO.l.l, the machine with all attachments installed shall not exceed 11 feet in Length.
