ARMY MIL-S-48464 B (1)-1993 SENSOR CROSSWIND 11733251《11733251 横风传感器》.pdf

上传人:brainfellow396 文档编号:448037 上传时间:2018-11-16 格式:PDF 页数:2 大小:64.28KB
下载 相关 举报
ARMY MIL-S-48464 B (1)-1993 SENSOR CROSSWIND 11733251《11733251 横风传感器》.pdf_第1页
第1页 / 共2页
ARMY MIL-S-48464 B (1)-1993 SENSOR CROSSWIND 11733251《11733251 横风传感器》.pdf_第2页
第2页 / 共2页
亲,该文档总共2页,全部预览完了,如果喜欢就下载吧!
资源描述

1、MIL-S-48464B (I) 9999906 1973784 901 I INCH-POUND 1 MIL-S-48464B (AR) AMENDMENT 20 December 1 1993 MILITARY SPECIFICATION SENSOR, CROSSWIND: 11733251 This amendment forms a part of MIL-S-48464B(AR) , dated 30 June 1981, and is approved for use by the U.S. Army Armament, Munitions, and Chemical Comma

2、nd, and is available for use by all Departments and Agencies of the Department of Defense. PAGE 2 Add “(REF)“ following the Inspection Equipment drawing numbers. PAGE 7 3.3.2.1 Pitch. Delete paragraph and substitute: “At a pitch angle of 15 , either positive or negative, wind velocities of 10 and 40

3、 miles per hour (mph), the assembly shall provide output voltages within the limits specified in Table I and Table II. for 3.3.2.2 Roll. Delete paragraph and substitute: “At a roll angle of 15 , either positive or negative, for wind velocities of 10 and 40 mph, the assembly shall provide output volt

4、ages within the limits specified in Table I and Table II. I PAGE 22 Delete paragraph 4.6.1 in its entirety and substitute: “4.6.1 Test equipment. The test equipment in Table VI1 may be used where specified to perform the required test. alternate test equipment is to be used, the contractor shall sub

5、mit inspection equipment designs for review and approval in accordance with the terms of the contract (see 6.4).“ If AMSC N/A 1 OF 2 FSC 1220 Distribution Statement A. distribution is unlimited. Approved for public release; Provided by IHSNot for ResaleNo reproduction or networking permitted without

6、 license from IHS-,-,-MIL-S-484b4B (1) 0b I1973785 848 MIL-S-48464B (AR) AMENDMENT 1 PAGE 26 Add new paragraph 6.4 as follows: “6.4 Submission of contractor inspection equipment desians for approval. Submit copies of designs as required to: Commander, US Army Armament Research, Development, and Engi

7、neering Center, ATTN: SMCAR-QAF-I (D), Picatinny Arsenal, NJ 07806-5000. This address will be specified on the Contract Data Requirements List, DD Form 1423 in the contract.“ Custodian: Army - AR Preparing Activity: Army - AR (Project 1220-A404) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 标准规范 > 国际标准 > ARMY

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1