1、MIL-S-53085 30 August 1988 MILITARY SPECIFICATION SURVEY INSTRUMENT AUTOMATED, INTEGRATED This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers portable, medium-range, of 2km through 7km, electro-optical dis
2、tance and angle measuring equipment. Distances are measured using diode-emitted infrared modulated light waves. Angles are determined by electronic measurement. . AISI measuring unit will be solid-state construction and complete with accessories for unsupported operation. 1.2 Classification. The AIS
3、I shall be of the following types, as specified: Type I - One Tenth (00.1“) second AISI with EDM modular unit of 7 kilometer cap ab i 1 i ty . Type II - One Tenth (00.1“) second AISI with EDM modular unit of 2 kilometer capab i li ty . Class A - With winterization kit. Class B - Without winterizatio
4、n kit. 1.2.1 Part number. The military specification part number for the automated integrated survey instrument shall be as follows: M 53085 - X - Y u Class A or B Type I or II -*/ Specification number. Do not include revision letter or activity. Prefix letter. ., Beneficial comments (recommendation
5、s, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: USA Belvoir Research, Development and Engineering Center, Attn: (STRBE-DS), Fort Belvoir, VA 22060-5606 by using the self-addressed Standardization Document Improvement Proposal (DD
6、 Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 6675 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. - THIS DOCUMENT CONTAINS -q/ PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MI
7、L-S-53085 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 SDecifications and standards. The following specifications and standards form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of
8、 the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation. SPECIFICATIONS FEDERAL A-A-208 V-T-276 W- C -440 TT - F- 325 ccc-c-419 CCC - D- 950 PPP - B - 601 PPP-B-636 PPP- c- 795 PPP-C-1842 - Ink, Marking, Stencil, Opaque. - Thread, C
9、otton. - Clip, Electrical, General Specification for. - Filler, Engraving, Stamped Marking. - Cloth, Duck, Cotton, Unbleached, Plied-Yarn , - Dyeing and Aftertreating Process as for Cotton - Boxes, Wood, Cleated-Plywood. - Boxes, Shipping, Fiberboard, - Cushioning Material (Flexible, Cellular, - Cus
10、hioning Material, Plastic, Open Cell. Army and Numbered. Cloth. Plastic Film) For Packaging Applications. MI LI TARY MIL-P-116 MIL-V- 173 MIL- P - 514 MIL-W- 530 MIL-H- 639 MIL- C - 67 5 MIL - T -7 O 4 MIL-D-3464 MIL-T-3530 MIL-B-11188 MIL-T-14091 - Preservation, Methods of. - Varnish, Moisture and
11、Fungus Resistant (For Treatment of Communications, Electronic, and Associated Equipment). - Plates, Identification, Instruction and Marking, Blank. - Webbing, Textile, Cotton, General Purpose, Natural or in Colors. - Hook (For Belts, Straps, and Equipage Items). - Coating of Glass Optical Elements,.
12、 (Antireflection). - Treatment and Painting of Materiel. - Desiccants, Activated, Bagged, Packaging Use and Static Dehumidification. - Thread and Twine, Mildew Resistant or Water Repellent Treated. - Batteries, Storage: Lead-Acid. - Tripod, Surveying: Extension-Leg-Type. 2 9 Provided by IHSNot for R
13、esaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-53085 66 7777706 OLLiL457 7 MIL-S-53085 MIL-T-14132 MIL- R- 14328 MIL-G-20241 MIL-B-23272 MIL-G-23827 MIL-T-43566 MIL-T-52114 MIL-B-81705 MIL-S-81733 - Theodolites, Surveying, Direction: Second Order. - Rubber Sheet, Syn
14、thetic, Medium Soft, General- Purpose Gasket Material (For Extreme Climatic Conditions). - Gasket Material, Wool Felt, Impregnated, Adhesive, Pressure-Sensitive. - Battery, Storage: Alkaline, Nickel-Cadmium. - Grease, Aircraft and Instrument, Gear and - Tape, Textile, Cotton or Polyester, General -
15、Theodolite, Surveying, Direction: Third Order. - Barrier Materials, Flexible, Electrostatic- - Sealing and Coating Compound, Corrosion Actuator Screw. Purpose, Natural or in Colors. Free, Heat Sealable. Inhibitive. : STANDARDS FEDERAL .-. FED-STD-H28 MI LI TARY MIL-STD-105 MIL-STD-129 MIL-STD-130 MI
16、L-STD-454 MIL-STD-461 MIL-STD-785 MIL-STD-810 MIL-STD-889 MIL-STD-1472 Screw Thread Standards for Federal Services. - Sampling Procedures and Tables for Inspection by Attributes. - Marking for Shipment and Storage. - Identification Marking of US Military Property. - Standard General Requirements for
17、 Electronic Equipment. - Electromagnetic Emission and Susceptibility Requirements for the Control of Electromagnetic Interference. - Reliability Program For Systems and Equipment Development and Production. - Environmental Test Methods. - Dissimilar Metals. - Human Engineering Design Criteria for Mi
18、litary Systems, Equipment and Facilities. 2.1.2 Other Government documents and Dubiications. The following other Government documents and publications form a part of this specification to the extent specified herein. Unless otherwise specified, the issues shall be those in effect on the date of the
19、solicitation. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-53085 PUBLICATIONS TB MED-524 - Occupational Environmental Health Control of Hazard to Health from Laser Radiation. (Application of copies should be addressed to the Commander, U.S.
20、Army Publication Distribution Center, 1655 Woodson Road, St. Louis, MO 63114.) NATIONAL BUREAU OF STANDARDS (NBS) Special publication 374 - Method for determining the resolving power of photographic lenses. (Application for copies should be addressed to the National Technical Information Service, 52
21、85 Port Royal Road, Springfield, VA 22161.) NATIONAL OCEANIC AND ATMOSPHERIC ADMINISTRATION (NOAA) Standards and specifications for Geodetic Control networks, September 1984. (Application for copies should be addressed to the National Geodetic Information Branch, N/CG174 Rockwall Bldg, Room 24, Nati
22、onal Geodetic Survey (NOAA), Rockville, MD 20852,) (Copies of specifications, standards, publications, and other Governmant documents required by contractors in connection with. specific acquisition func- tions should be obtained from the contracting activity or as directed by the contracting office
23、r.) 2.2 Other Dubiications. The following document(s) form part of this specification to the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted shall be those listed in the issue of the DODISS specified in the solicitation. Unless otherwise specifi
24、ed, the issues of documents not listed in the DODISS shall be the issue of the non- Government documents which is current on the date of the solicitation, SOUTH COAST AIR QUALITY MANAGEMENT CONTROL DISTRICT Rule 442 - Usage of solvents. (Application for copies should be addressed to the South Coast
25、Air Quality Management Control District, 9150 Flair Drive, El Monte, CA 91731.) (Non-Government standards and other publications are normally available from the organizations which prepare or which distribute the documents. These documents also may be available in or through libraries or other infor
26、mation services.) 4 I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-53085 66 W 7777906 LLILi.157 2 W . _- .- - _- / MIL-S-53085 2.3 Order of precedence. In the event of a conflict between the text of this specification and the references cite
27、d herein, the text of this specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws and .-_. regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Description. A surveying total station system, more specifically the automat
28、ed integrated survey instrument, hereinafter referred to as AISI, shall combine three major modular subassemblies into a single, compact field survey instrument package: (i) the Electronic Theodolite (ELT), an auto-reading/ recording digital theodolite with electronic display/control panel; (2) the
29、Electronic Distance Meter (EDM), a low power, miniaturized distance measuring device with a range and accuracy compatible with the ELT; (3) the Data Recorder Unit (DRU), an automatic data recording/storage/processing terminal, ruggedized for field use with the ELT and EDM, and interoperable with any
30、 microprocessor through a RS232 interface. The AISI shall be mountable for operation on the standard military tripod specified in MIL-T-14091 using the universal tribrach specified in MIL-T-14132. The AISI shall also include; transport carry case or cases, retro-directive prisms, two 12 volt nickel
31、cadmium (NiCad) battery packs, battery charger, auxiliary external power cable not less than 6 meters in length, tribrachs, accessories, tools, accessory cases and survey system software programs (see 6.2m) for computation, plotting or printing. When specified (see 6.2), a winterization kit, thermom
32、eter, altimeter-baroneter, meteorological correction data, tripods, and backpack shall also be included. The AISI shall electronically measure the value of subtended horizontal and vertical angles, measure slope distances to a maximum range of 7km or 2km for a type I or type TI instrument respective
33、ly and automatically record these data in a data storage/ processing module for on-site reduction or transfer via computer interface to a microprocessor. Additionally, provided with appropriate input data, the AISI shall be able to cue the lay-out of horizontal and vertical earthmoving operations. 3
34、.2 First article. Unless otherwise specified (see 6.2), a sample shall be subjected to first article inspection (see 4.3 and 6.7). Any changes or devia- tions of the AISI from the approved first article during production will be subject to approval of the contracting officer. Approval of the first a
35、rticle will not relieve the contractor of his obligation to furnish the AISI conforming to this specification. 3.3 Material. Material shall be as specified herein. Materials not specified shall be selected by the contractor and shall be subject to all provisions of this specification. 3.3.1 Material
36、 deterioration prevention and control. The AISI shall be fabricated from compatible materials inherently corrosion and deterioration resistant or treated to provide protection against the various forms of corrosion and deterioration that may be encountered in any of the applicable storage and operat
37、ing environments to which the AISI may be exposed. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-530B5 bb 777770b OL4L460 Si MIL-S-53085 3.3.1.1 Dissimilar metals. Dissimilar metals shall not be used in intimate contact with each other unle
38、ss protected against galvanic corrosion, Dissimilar metals and methods of protection are defined and detailed in MIL-STD-889. 3.3.1.2 Identification of materials and finishes. The contractor shall identify the specific material, material finish or treatment for use with components and subcomponents,
39、 and shall make information available, upon request, to the contracting officer or designated representative. 3.3.2 Recovered materials, For the purpose of this requirement, recovered materials are those materials which. have been collected from solid waste or reprocessed to become a source of raw m
40、aterials, as distinguished from virgin raw materials, The components, pieces and parts incorporated in the AISI may be newly fabricated from recovered materials to the maximum extent practicable, provided the AISI produced meets all other requirements of this specification. Used, rebuilt or remanufa
41、ctured components, pieces and parts shall not be incorporated in the AISI. 3.4 Environmental reauirements. 3.4.1 Operational temperature. The AISI shall operate with no external assistance, without damage from an internal or external 12-volt power source, with the accuracy specified herein when in t
42、hermal equilibrium in air at any temperature from 50 to -20 OC. The AISI shall operate without damage and with the accuracy specified herein from -17 to -42 OC using an external winterizati-on kit. 3.4.2 Storane temperature. The AISI shall not be damaged by storage under the following conditions: Hi
43、gh air temperature - 4 hours at +71 OC. Low air temperature - 6 hours at -45 OC. 3.4.3 Solar radiation. The AISI shall operate without damage within the accuracy specified herein when subjected to solar radiation of 355 Btu/ft squaredfiour, for not less than 4 hours in an ambient air temperature of
44、43 +O, -1.7 oc. 3.4.4 Humidity. The AISI shall not be damaged and shall operate within the accuracy specified herein when subjected to relative humidities of at least 95 percent at air temperature varying between -20 +1, and 50 the bearings, motion clamps and screws need not be sealed. 3.10.3.1.4 Ci
45、rcles. 3.10.3.1.4.1 Horizontal and vertical circle. The horizontal and vertical circles shall be graduated with encoded tracks electronically readable by the integral microprocessor. Sensing of diametrically opposite projections shall prbvide for a means of automated correction for circle eccentrici
46、ty and varia- tions in circle graduations. In conjunction with an electronic micrometer, the resolution of the circle readings shall be 0.5“. The initial display time shall not exceed 1.0 second, Inclination of the vertical axis shall be detected, corrected and automatically applied to readings by a
47、 compensator system. Verti- cal angle measurements shall be automatically indexed within a sensing range of +/- 10 to an accuracy of +/- 0.5“. The units of angular measurement shall be operator selectable on the keyboard in either sexagesimal or decimal. . 3.10.3.1.4.2 Setting circles, A horizontal
48、and vertical circle setting device shall be furnished for setting the circles in various positions of an observation .program. The circles will be provided with a means of selecting the units of angular measure so they will correspond to those selected on the mcroprocescor. The circle setting device
49、 shall have free movement without binding throughout full revolution, Positive means shall be provided to prevent inadvertent movement by the observer. 3.10.3.1.5 MiCrODrOCeSSOr disDlav/control Danel. 3.10.3.1.5.1 Keyboard. Panel dials, displays, knobs and switches shall be functionally grouped, color coded and constructed for simple operation located on both sides of the theodolite. Each shall be marked to identify its functional name, symbol, operating instruction reference. To
