1、MIL-T-45305C 23 9999906 0476725 b W I NOT MEASUREMENT SE Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: US Army Tank-Automotive Command, ATTN: AMSTA-UED, Warren, MI 48397-5000, by using the sel
2、f-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of thie document or by letter. MIL-T-45305C(AT) SUPERSEDING MIL-T-45305B(AT) 9 May 1980 ri1 2391 I MILITARY SPECIFICATION * TRUCK, BOOKMOBILE: DIESEL OR GASOLINE ENGINE DRIVEN, 1 16,000 POUNDS GVW, 4x2, MOD
3、IFIED COMMERCIAL This specification is approved for use by the US Army Tank Automotive Command, Department of the Army, and is available for use by all Departments and Agencies of the Department of Defense- 1. SCOPE 1.1 Scow. control chassis. gross vehicle weight (GVW) of not less than 16,000 pounds
4、. under this specification are commercial items which are warranted by the manufacturer as specified in acquisition documents. This specification covers a bookmobile mounted on a forward The vehicle is a four wheel, two-wheel-drive truck having a Vehicles procured 2. APPLICABLE DCMENTS . The followi
5、ng * 2.1.1 SDecifications. st;tndards specifications, standards and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODIS
6、S), and supplement thereto, cited in the solicitation (see 6.2). I AMSC N/A i- Approved for public release; distribution is unlimited. e Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-* MIL-T-45305C 23 999990b 047b72b W MIL-T-45305C(AT) SPECIFICATIO
7、NS FEDERAL A-A-393 W-B-131 STANDARDS FEDERALI FED-STD-297 MILITARY MIGSTD-1223 - Zxtinguisher, Fire, Dry Chemical (Portable). - Battery, Storage: Vehicular, Ignition, Lighting and Starting. - Rustproofing of Commercial (Nontactical) Vehicles. - Nontactical Wheeled Vehicles Treatment, Painting, Ident
8、ification Marking and Data Plate Standards. * (Unless otherwise in( icated, copies of federal and military specifications, standards, and handbooks are available from the Naval Publications and Forms Center, Military Specifications and Standards, Bldg. 4D, 700 Robbins Avenue, Philadelphia, PA 19111-
9、5094.) * 2.1.2 mer Gcrvermmt wents. dra-6. and Rubucati- . The following other Government documents form a part of this specification to the extent specified herein. Unless otherwise specified, the issues shall be those in effect on the date of the solicitation. t DEPARTMENT OF DEFENSE Department of
10、 Defense Index of Specifications and Standards (DODISS). (Copies of the WDISS are available on a yearly subscription basis either form the Government Printing Office for hard copy, or microfiche copies are available from the Director, Navy Publication and Printing Service Office, 700 Robbins Avenue,
11、 Philadelphia, PA 19111-5093.) DEPARTMENT OF TRANSPORTATION (DOT) Federal Motor Carrier Safety Regulations. Federal Motor Vehicle Safety Standards. (Application for copies of WT publications shoi Id reference the Code of Federal Regulations, 49 CER, and the Federal Register and should be addressed t
12、o the Superintendent of Documents, U.S. Government Printing Office, Waahington, D.C. 20402. ) ENVIRONMENTAL PROTECTION AGENCY (EPA) Control of Air Pollution from New Motor Vehicles and New Motor Vehicle Noise Emission Standards for Transportation Equipment - Medium and Engines. Heavy Trucks, 2 Provi
13、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-45305C 23 9999906 0976727 T m (Application for copies of EPA publications should reference the Code of Federal Regulations, 40 CFR, and the Federal Register and should be addressed to the Superintenden
14、t of Documents, U.S. Government Printing Office, Washington, D.C. 20402.) * 2.2 b - Gover- - The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DODISS
15、cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the documenta cited in the solicitation (see 6.2). * THE EUROPEAN TYRE AND RIM TECHNICAL ORGANISATION (E3XTO) Standards Manual (Application for copies of the ETRTO publicationa s
16、hould be addressed to the European ere and Rim Technical Organisation, 32, Avenue Brugmann, 1060 Brussels, Belgium.) NATIONAL FIRE PROTECTION ASSOCIATION (NFPA) NFPA-70 - National Electrical Code. (Application for copies of NFPA publications should be addressed to the National Pire Protection Associ
17、ation, Batterymarch, Park, Quincy, MA 02269.) STATE OF CALIFORNIA Vehicle Code of California (Application for copies of State of California publications should be addressed to the Department of Motor Vehicles, 2570 24th Street, Sacramento, California 95809.) SOCIETY AIJTOMOTIVE ENGINEERS, INC- (SAE)
18、 SAE Standards and Recommended Practices 5537 - Storage Batteries. 5551 - Performance Levels and Methods of Measurement of Electromagnetic Radiation From Vehicles and Devices (30-1000 MHz). 5588 - Turn Signal Lamps. 5589 - Turn Signal Switch. 5688 - Truck Ability Prediction Procedure (hD - Engine Po
19、wer Test Code - Spark Ignition and adopted) - Diesel I * Ji349 (Application for copies of SA6 publications should be addressed to SAE, Inc., 400 Commonwealth Drive, Warrendale, PA 15096.) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-T-45305
20、C 23 H 9999906 0476728 1 MIL-T-45305CCAT) THE TIRE AND RIM ASSOCIATION, INC. Year Book. ik (Application for copies of Tire and Rim Association publications should be addressed to the Tire and Rim Association, Inc., 175 Montrose West Ave., Copiey, OH 44321,) . 1 (Non-Government standards and other pu
21、blications are normally available from the organizations that prepare or distribute the documents. documents also may be available in or through libraries or other informational services.) These * 2.3 this document and the references cited herein, the text of this document shall take precedence- Not
22、hing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. In the event of a conflict between the text of 3- REQUIREXENTS * 3.1 Stardard vehiia ance- - Except as specified in 3.1.1 through 3.1.1.8, the vehicle, components, assemblies, an
23、d accessories to be delivered under the contract shall be standard or optional items, which meet or exceed the requirements of this specification. Except as specified in 3.1.1 through 3.1.1.8, no removal, substitution or alteration of the chassis manufactuers standard or optional chassis model compo
24、nents shall be made. All chassis items shall be as represented in the chassis manufacturera technical data book. represented in the body and equipment manufacturers technical data. Technical data shall be limited to specifications and technical material, identical to that furnished to the authorized
25、 company representatives for selection of vehicle models and components, and shall be available to the engineering offices of the procuring activity, prior to delivery of the items. The chassis model furnished shall be not older than the chassis manufacturers current model on the date of invitation
26、for bids. Special bodies or mounted equipment shall be as 3.1.1 Sixlcjal reailiremen.ts - In addition to the standard vehicle and components specified in 3.1, the vehicle shall be furnished with special equipnent as specified herein. . * 3.1.1.1 body; full complement of fuel, lubricants and coolant-
27、 consist of the curb weight, operator weight (computed at 175 pounds) and a payload to provide not less than the specified GVW. 3.2.5 lirosa vehicle wei A coolant shutoff valve shall be provided for the coolant inlet side of the fuel warmer unit. * 3.4.1.9 fie1 fired engine Dreheakr . When specified
28、 (see 6.2), for diesel engine driven vehicles, a diesel fuel fired engine water heater shall be furnished to preheat the engine. The heater shall include a timer, a thermostat and a circulating pump and shall be connected to the engine coolant system. minus 60oF and shall heat the engine to plus 400
29、F from minus 60oF in not more than 1 hour. the driver, to indicate that the preheater is operating. The heater shall be capable of starting and operating at The system shall be equipped with a light, visible to 3.4.2 Plectrbal sustems . The electrical system shall be in accordance with Federal Motor
30、 Carrier Safety Regulations 393.27 through 393.31 and 393 I 33. L 3.4.2.1 CtarjsvRtem . For diesel engine driven vehicles, a 12- or 24-volt direct current (dc) starting system, with a 12-volt dc lighting system shall be furnished. Engine starting equipment shall include an ether starting system, glo
31、w plug or electric grid heater. furnished in lieu of a glow plug or grid heater, it shall be of the measured shot type. manually operated from the drivers compartment and shall be inoperative with the engine warm. not less than 12 fluid ounces shall be furnished. furnished. If an ether system is The
32、 measured shot type ether system shall be key operated or Complete provisions for a replaceable ether reservoir of A reservoir need not be . For gasoline engine driven vehicles, a 12-volt * 3.4.2.2 de ignition system shall be furnished. * 3.4.2.3 m. Unless otherwise specified (see 6.2) on diesel eng
33、ine driven vehicles, a minimum 65-ampere alternator shall be furnished. The alternator output with the engine at engine idle speed shall be not less than 45 amperes. Unless otherwise specified (see 6.2) on gasoline engines driven vehicles, an alternator of not less than 85 amperes rated capacity, an
34、d which provides not less than 45 amperes de output at normal engine idle speed, shall be furnished. * 3.4.2.4 UghLing. All vehicle lights, reflectors, and wiring shall be as specified herein and shall conform to Federal Motor Carrier Safety Regulations 333.12, 393.13, 333.19, 393.20 and 333.22 thro
35、ugh 333.26(63. 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-45305C 23 999990b 047b734 7 Reserve capacity Engine type (minutes) Positioning and guarding shall permit normal replacement of the bulbs and lenses. rub rails (unless recessed and
36、 fully protected) or mounted on vehicle bumpers. When right hand drive is specified by acquisition documents, left- dip headlights shall be provided. replacement set, stowed in the cab for shipment. Lights and reflectors shall not be mounted on vertical surface of Left-dip headlights may be provided
37、 as a Cold cranking (amperes 1 * 3.4.2.5 . Turn signal lamps shall conform to SA3 5588. Operating units shall conform to SAE 5589, class A, and shall be mounted on the steering column. TurnSignal units shall be installed in accordance with SAE 5588. Turn signal operating units shall be self-cancelli
38、ng type with a visible and audible type flash indicator. * 3.4.2.6 Batteries - Each battery shall be of 12-volt potential. The total reserve capacity rating and the total cold cranking rating at OF, both measured in accordance with SAE 5537, shall be not less than as specified in table I. the mainte
39、nance free characteristics listed in W-B-131. Batteries shall be of the maintenance free type having Gasoline Diesel TABLE I. Batteriea. I 100 450 230 1,100 . * 3.4.2.7 Radioerfwcmce suvmesriinn for radio interference in accordance with CAE 5551. Any body equipment emitting radio interference shall
40、be suppressed to the same level as the vehicle chassis. The vehicle shall be suppressed arocessine: . The vehicle shall be processed for ahiment, from manufacturers plant to initial receiving activity, in accordance with manufacturers standard commercial practice. 6. NOTES 6.1 Intendeduse. Bookmobil
41、es covered by this specification are intended to provide library service to off-post sites; to be operated by a male or female librarian over improved or unimproved roads and highways, under all conditions of weather and climate encountered within the continental limits of the United States and at v
42、arious altitudes and grades which may be encountered on the main roads, highways and access roads within the continental limits of the United States. * * * * * * * * * * * in &ta. Acquisition documents should specify the following: Title, number and date of this specification. Issue of DODISS to be
43、cited in the solicitation and if required, the specific issue of individual documents referenced (see 2.1.1 and 2.2) I Identification of the appropriate military service for painting (see 3.1.1.1). Identification of the appropriate military service for marking (see 3.1.1.2) - Concealed markings, if
44、required (see 3.1.1.2). Rustproofing, if required (see 3.1.1.3). Tropical rustproofing, if required (see 3.1.1.3). Gasoline engine, if required (see 3.4.1.2). Silicone rubber hoses, if required (see 3.4.1.7). Power plant heaters and fuel warmer, if required (see 3.4.1.8). A fuel fired engine preheat
45、er, if required for a dieael engine driven vehicle (see 3.4.1.9). Alternator capacity, if other than as specified, (see 3.4.2.3). Disc type wheels, if required (see 3.4.10). Carrier for spare tire, if required (see 3.4.10.3). A apare wheel or rim, if required (see 3-4.10-4). A spare tire, if require
46、d (see 3.4.10.5). Tools, if required (see 3.4.15). 21 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-45305C 23 W 999990b 047b74b 3 . * 6.3 Performpnce Drediction computations and computation for low speed and maximum geared speed will be requi
47、red by the contract. The SAE Work Sheet Item 1 should include vehicle model number, engine model number and vehicle type. Unless other conditions are cited in the contract, computations should be made for normal atmospheric pressure, normal ambient air temperature and still, dry air. The factors to
48、be uaed in predicting truck ability (see 3.3.1.1) are established as follows for the corresponding SAK Truck Ability Prediction Procedure Tables: CAE Truck Ability Prediction Procedure - Table 1 Table 2 Table 3 Table 4 Table 5 Table 6 Table 7 Table 8 Table 8A Table 9 - re Factcui. This factor must r
49、elate to the size of tire furnished by the contractor in accordance with this specification. - e FanW. 1.00 - u Fac-. 1.613 - v Factnr. 250.0 - Fach. 1.00 - AreaFactor. 0.175 - Use vehicle GVW (to nearest, higher, 1,000 pounds) and the engine rpm (to nearest 100 revolutions) which is required for 50 mph geared speed. For GVW and engine speed beyond the range of this table, factors shall be extrapolated. - - sirade Facht. 0.75 - ectm Facta. Not required. - 8-u. O.O. Libra
