1、MIL-T-49303 58 997790b OLb329b O /INCH-POUNDI MIL-T-49303 (CR) 18 August 1988 MILITARY SPEC1 FICATION TRANSPONDER SET AN/PPN-lg(V) This specification is approved for use within the Communications- Electronics Command, Fort Monmouth, New Jersey, Department of the Army, and is available for use by all
2、 Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the requirements for construction and testing of Transponder Set AN/PPN-lg(V) (Mu1 ti function Radar Transponder Beacon). AN/PPN-l9(V) is a self-contained. 1 ightweight, man portable unit designed f
3、or field service, and shall consist of: Transponder Set AN/PPN-19 (V)l Configuration Receiver - Transmitter, Radar, RT-1493/PPN-19 (V) C5083053 Antenna, AS-3779/PPN-l9(V) C5083043 Switch, Waveguide, SA-2495/PPN-l9(V) C5083033 Control , Transponder Set, C-116Ol/PPN-l9(V) C5083321 Transponder Set AN/P
4、PN-l9(V)2 Configuration Receiver, Transmitter, Radar, RT-1493/PPN-l9(V) C5083053 Antenna, AS-3779/PPN-l9(V) C5083043 Switch, Waveguide, SA-2495/PPN-l9(V) C5083033 Control , Transponder Set , C-11601/PPN-l9(V) C5083321 Battery Box, CY-8412f PPN-l9(V) C5083329 2. APPLICABLE DOCUMENTS 2.1 Government do
5、cuments. 2.1.1 Specifications and standards. The following specifications and standards form a part of this specification to the extent specified herein. Unless otherwise -specified, the issues of these documents. shall be those listed in the Department of Defense Index of Specifications and Standar
6、ds (DODISS) and supplement thereto, cited in the solicitation. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commander , US Army Communications-Electronics Command and Fort Monmouth, ATTN: AMS
7、EL-ED-io, Fort Monmouth, New Jersey 07703-5000 by using the sel f-addressed Standardization Document Improvement Proposal (OD Form 1426) appearing at the end of this document or by letter. AMSC - N/A FSC 5895 DISTRIBUTION STATEMENT A. Approved for public release; distribution unlimited. THIS DOCUMEN
8、T CONTAINS x! PAGES. Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-LI9303 58 977970b OLb3277 2 MIL-T-49303( CR) - .- -. P SPECIFICATIONS MILITURY MIL-P-li6 - Preservation-
9、Packaging, Methods of. MIL-P-112b8 - Parts, Materials, and Processes Used in Electronic Equ i pment . MIL-M-13231 - Marking of Electronic Items. MIL-F-14072 MIL-P-l5U24/6 - Plate, Identification-Information and Marking for MIL-T-28800 MIL-E-55585 - Finishes for Ground Electronic Equipment. Identific
10、ation of Electrical, Electronic and Mechanical Equipment. Equipment, General Specification for. - Test Equipment for use with Electrical and Electronic - Electronics Equipment and Parts, Packaging of. STA N iy RDS M I L I TA RY MIL-STU-105 - Sampling Procedures and Tables for Inspection MIL-STD-252
11、- Wired Equipment, Classification of Visual and MIL-STO-454 MIL-STD-461 MIL-STO-462 - Electromagnetic Interference Characteristics, MIL-STD-720 - Packaging Requirements Code. MIL-STU-7dl MIL-STO-1472 MIL-STD-810 - Environficntal Test Methods. MIL-STO-2073-2 - Packaging Requirement Codes by Attribute
12、s. Mechanical Defects. Equ i pment. Requirements for the Control of Electromagnetic Interference. Measurement of. - Standard General Requirements for Electronic - Electromagnetic Emission and Susceptibility - Reliability Tests Exponential Distribution. - Huriian Engineering Design Criteria for Milit
13、ary Systems, Equipment and Facilities. 2.1.2 Other qovernment documents and drawings. The fol lowing other government documents, drawings, and publications form a part of this specification to the extent specified herein. Unless otherwise specified, the issues shall be tnose in effect on the date of
14、 the solicitation. DMWINGS DLC5083U30 C5Ud3031 - ATP, Switch Cap C5083U33 - Switch Cap Assembly C5083043 - Omnidirectional Antenna Assembly - Transponder Set Assembly, AN/PPN-19. 2 Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or
15、networking permitted without license from IHS-,-,- MIL-T-49303 58 m 44999Ob 03b3278 4 m ri C5063053 C5083058 CS08305 9 C 5083 106 C 5083 11 2 C 50831 19 C5083121 C5083126 C 5083 151 C5U83ZUl C5083214 C 5 083 2 2 7 C5083238 C 5083259 C 5083 263 CSu83266 C5083276 C5083278 C5063279 C SO83293 C5083306 C
16、508332i C 5083322 CS83329 C5083333 C5083347 C5083449 C 5087088 C50b7090 CS087094 C 587096 C5087098 C 587 AO0 C5087102 CS87104 C 5087 i00 CW87 108 C5087110 MIL-T-45303 (CR) - Receiverflransmi tter Assembly - Signal Processor Assembly - ATP, Signal Processor Unit - ATP, Encoder - ATP, Panel Interface
17、- Control Panel Assembly - Power Supply Assembly - ATP, RF Cable - ATP, I-Band RF Head - ATP, J-Band RF Head - ATP, Bit Source - ATP, J-band MG/MOi) - ATP, I-Band bNG/MOil - ATP, Control Panel - ATP, I-Band IF - ATP, I-8and IF Amplifier - K-Band Video Assembly - ATP, K-Band Video - ATP, J-Band Viaeo
18、 - ATP, J-Band FkT Amplifier - Remote Control Unit Assembly - ATP, Remote Control Unit - Gattery $ox Assembly - ATP, Battery Protection - ATP, Power Supply - ATP, K-Band Detector - ATP, I-Band Preselector - ATP, J-Band Preselector - ATP, RF Transition - ATP, J-Band Filter/Det - ATP, I-Band Horn - AT
19、P, J-Band Horn - ATP, K-Band Horn - Preliminary Alignment and Test Procedure - Final Acceptance Test Plan (ATP). - ATP, Battery Box Adaptor - ATP, MPU - ATP, DRO (Copies of specifications, standards, drawings and publications required by contractors in connection with specific procurement functions
20、should be obtained from the procuring activity or as directed by the contracting officer.) 2.2 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein (escept for associated detail specification, specification sheets or MS standards), th
21、e text of this specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specified exemption has been obtained. Y- %-* 3 Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo
22、reproduction or networking permitted without license from IHS-,-,-MIL-T-q9303 50 m 9999906 0163299 b MIL-T-49;03( CR) -._ / Y 3. REQUIREMENTS 3.1 First article. When specified, the contractor shall furnish first article units for first article inspection and approval (see 4.3 and 6.2). 3.2 Construct
23、ion. The Transponder Set AN/PPN-lS(V) shall be constructed in accordance with the requirements of this specification, DLC5083030, and the following list of major components: Component Drawing Switch Cap Assembly Omnidirectional Antenna A ssembly ReceiverlTransmi tter Assembly Signal Processor Assemb
24、ly Control Panel Assembly Power Supply Assembly Remote Control Unit Assembly Battery Box Assembly C5083033 C5083043 C 508305 3 C5083058 C5083121 C5083126 C5083321 C5083329 3.3 Parts, materials and processes; general. In addition to the reauirements of this saecif ication. the reauirements of MIL-P-1
25、1268. iniluding the selection reqirement threin, shali apply (see 4.4). 3.3.1 Recycled, virgin and reclaimed materials. It is required that, to the maximum extent possible, recovered or reclaimed materials, in lieu of virgin materials, shall be used without jeopardizing the intended use of the manuf
26、actured item. 3.4 Finish. All surfaces of the AN/PPN-l9(V) requiring a protective coating shall be finished in accordance with MIL-F-14072 and the equipment drawings specified herein. (See 4.4). 3.5 Nameplate and marking. 3.5.1 General. Marking of AN/PPN-(V) shall be in accordance with MIL- M-13231
27、(sGFKKI). 3.5.2 Visibility. Whenever practicable, parts shall be so mounted that their identification marking will be readily visible with minimum disassembly of the equipment. 3.5.3 Nameplates. Each nomenclature item shall have a nameplate conforming to MIL-P-15024/b, Type H or B (see 4.4) B 3.5.4
28、Serial numbers. Each AN/PPN-l9(V) shall be serial numbered. 4 Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-q7303 58 W 9797706 0363300 7 MIL-T-49303( CR) 3.6 Safety engine
29、ering. 3.6.1 Personnel hazards. Personnel hazards shall be kept to a minimum. The criter- shall be made applicable for tasks and efforts such as the selection of parts, the complete manufactuing and assembly process, and any product baseline configuration changes that may be implementea during the c
30、ourse of the contract. Verification that compliance with this requirement has been achieved shall be through a visual inspection (See 4. U). 3.6.2 Edge rounding exposed. Exposed edges and corners shall be rounded sufficiently to minimize laceration/puncture hazards, the design goal being a (12.7 mm)
31、 for corners. minimum-radius of 0.04 inch (I mm) for edges and a minimum of 0.5 inch 3.6.3 Radioactive materials. Radioactive materials shall not be used (e-g. luminous dials/markings, electron tubes, surge arrestors and lenses). 3.7 Interchangeability. 3.7.1 Mechanical interchangeability. Like unit
32、s, assemblies, subassemblies and replaceable parts shall be physically interchangeable without modification and shall conform to Requirement 7 of MIL-STD-454 (see 4.8). 3.7.2 # Like units, assemblies, subassemblies and replaceable parts shall be functionally interchangeable without modification anci
33、 shall conform to Requirement 7 of MIL-STO-454. Electrical adjustment may be macle at all maintenance levels as referenced in the manuals (see 4.8). 3.8 Dimensions and weights. The weight of receiver-transmitter shall not exceed 17.75 lbs (6. kg) excluding battery box. The dimensions of the receiver
34、-transmitter shall be 12.7% x 4075 x 8.68 inches (32.4cm x 12cm x 22cm) excluding protrusions and battery box. The weight of battery box, excluding batteries, shall not exceed 4.5 Iba (2.0kg). The dimensions of the battery box shall be 12.75 x 5.1 x 5.0 inches (32.4 cm x 13 cm x 12.7 cin) excluding
35、protrusions (see 4.7) e 3.9 Environmental stress screenin1 (ESS). The AN/PPN-l9(V) shall meet the perfmment-ified herein after subjection to vibration and electrical preconditioning test of 4.6. 3.10 Performance requireme The AN/PPN-l9(V) shall meet the performance requirements as specified in 3.2 a
36、fter subjection to the test OP 4.9. 3.11 Service conditions. The AN/PPN-19(V) shall. meet the following service CO-. Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-Ll7303 5
37、8 !B!l 7797706 OLb330L O MIL-T-4933i CR j 3.1.1 Altitude. The AN/PPN-i9(V), including battery box shall meet specified performance, without degradation, at altitudes up to and .ineluding 10,000 feet (3048m) above sea level, and shall withstand air transportation at altitudes up to 40,000 feet (12,19
38、2m) above sea level (see 4.0.1)* 3.11.2 High temperature. The AN/PPN-lg(V), including battery box shall be operable without deterioration damage or degradation in spec-ified performance at ambient air temperature as high as +125OF (51.67OC), plus the effect of solar radiation at a rate of 360 BTU/ft
39、z/hr. The AN/PPM-L!3(V) shall be permitted a one minute cool-down period before full operation -ia required. At the end of the one minute period, the AN/PPN-lg(V) shall provide full specified performance. The AN/PPN-lg(V), including battery box, shall be capable of withstanding without degradation o
40、f specified performance long periods of storage at temperature as high as +160QF (71. lOC) (see 4.10.2). 3.11.3 Low temperature. The AN/PPN-l9(V), including battery box, shall be operable without deterioration damage or degradation in specified performance at air temperature as low as -5OOF (-45.6OC
41、). The AN/PPN-19(V), including battery box, shall be capable of withstanding, without degradation of specified performance, long periods of storage at temperatures as IQW as -7OOF (-56.7%) (see 4.10.3). 3.11.3.i Warm-up time. The receivers, transinitters, power supply, and associated circuitry shall
42、 become fully stabilized within the system operational parameters specified herein in a time period not to exceed one minute under all operational service conditions specified herein, except below -1WC. An increased time shall be allowed for frequency stability in a linear manner from one minute at
43、-1OOC up to five minutes at -4IiOC. Stabilization time is measureti from the time of application of the specified system input voltages. 3.1.4 Humidity. The AN/PPN-lg(V), including battery box, shall be operable without degradation in specif led performance, and shall sustain no physical damage, dur
44、ing and after prolonged exposure to extreme humidity levels as encountered in tropical areas (see 4.10.4). 3.11.5 Salt fog. After the salt fog test of 4.10.5, the AN/PPN-l9(V), includ-ing battery box shall operate without degradation in specified performance and show no evidence of degradation, such
45、 as flaking, pitting, blistering, or loosening of finish or metal surface exfoliations. There shall also be no clogging or binding of moving mechanical parts. 3.11. Fungus. After the fungus test of 4.10.6, the AN/PPN-lg(V), Sncluding battery box, shall be visually examined. The AN/PPN-l9(V) shall sh
46、ow no more than sparse microbial growth with restricted tuberal growth development in an .area 10 percent or less of the total area, and no more than six unrelated minuted colonies with mycelial development in only areas 6 Copyright Communications - Electronics Command Provided by IHS under license
47、with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-q9303 58 M 9797906 0363302 2 W I MIL-T-49303 (CRj other than critical circuit portions; auch as terminal spacing, printed curcuit boards, etc., with sparse growth due to random contamination or traces o
48、f unmixed material ingredients. In addition, the AN/PPN-19(V) shall operate without degradation in specified performance after exposure to the test conditions of 4.10.6. Materials used in the manufacture, fabrication, construction and treatment of the AN/PPN-l9(V) shall comply with Requirement O 4 O
49、f MIL-STD-454. 3.11.7 Rain. ThB AN/PPN-19(V), including battery box, shall be operable without degradation in specified performance, and shall sustain no physical damage, during period of heavy precipitation with intermittent wind. (See 4.10.7) 3.11.8 Immersion. The AN/PPN-l9(V) , including battery box, shall be immersion proof to a covering depth of 3 feet of water for a period of not less than 2 hours. 3.11.9 Wind. The AN/PPN-19(Vj, including bat
