1、MIL-T=6=33(MO) i3 January 1966 MILITARY SPECIFICATION TRUCK, DW; CcMMERCIALj GASOLINE ENCINE DFUVENj 1OjooO POUNDS GVW, 4x2 1. SCOPE 1.1 Scope. This specification covers gasoline-engine driven, four-wheel, two-rear-wheel drive, 10,oOo pound gross vehicle weight (GW) , dump truck. Vehicle procured un
2、der this specification ia a ccamnercid. item which shall be warrented by the manufacturer as specified in procurement documents. 2. APPLICABLEWCUMENTS 2.1 The following documents of the issue in effect on ate of invitation for bids or request for prpsal, form a part of this specification to the exte
3、nt specified herein. SPECIFICATIONS Federal F-F-351 - Filters and Flter Elements; Lubricating Oil; Internal Combustion Engines. STANDARDS Military MIL-STD-642 - Identification Marking of Administrative , combat, and Tactical Transport Vehicles, MILsTD-lZ3 - AdminisCYrative Wheeled Vehicle Undercoati
4、ng, Treatment, Painting and Data Plates Standard. Release . MS 51335 - Phtle Assembly, TCWhlg - 18,000 LbS. Capacity, ManUd. (Copies of specifications, standards , rawings , and publications required by suppliers in connection with specific procurement functions should be obtained from the procuring
5、 activity or as directed by the contracting officer.) 2.2 Other publications. The followlng documents fonn a part of this speci- fication to the extent specified herein. in effect on date of invitation for bids or request for proposai shall apply. Unless otherwise indicated, the issue THIS DOCUMENT
6、CONTAINS 3 PAGES. 1, Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-62033 (MO) INTERSTATE CCYIiMERCE CCBMISSION Motor Carrier Safety Regulations (ICC) (Applications for copies should be addressed to the Interstate Commerce Commission, Bureau o
7、f Motor Carriers, Washington, D.C. 20423) STATE OF CALIFORNIA California Vehicle Code. (Application for copies should be addressed to Department of Motor Vehicles, 2570 24th Street, Sacramento, California 95804.) TRUCK BODY AND F3 body; and full cout;3lement of fuel, lubricants and coolant. 3.2.2 Gr
8、oss vehicle weight. Gross vehicle weiglrit (GVW) shall consist of curb weight, operator (weight cwuted at 175 pounds), and a peyload, distributed evenly over the vehicle load area, to provide not less than the specified GW. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted witho
9、ut license from IHS-,-,-. MIL-T-62033 23 m 9777706 0397752 I MIL-T-62033(MO) 3.2.3 Weight distribution. The distribution of GVd for the purpose of establishing suspension, axle and tire capcities skiall be determined with the payload uniformily distributed over the load- ar?ar 3.2.4 Hating. Componen
10、t and vehicular rating shall not be raised to meet the requirements of this specification. Minimum GVii rating shall be 10,000 pourxis . 3.3 Performance. 3.3.1 Speeds and gradeability. Vehicle shall maiiltain a high speed of not less than 60 miles per hour (mph) on smooth, apgcoxirmtely level, hard
11、surfaced roads; vehicle shall be capable of asceniDg grades of at least :Ge -bon steel. Body floor shall be one piece, flat with no protrusions or depressions and fabricated frcun not less than lO- adjustment of the engine, electrical and brake system; filling and charging of battery; alinement of f
12、ront wheels; inflation of all tires; camplete lubrication of chassis, engine, and running gear, with grades of lubricants recommended for the ambient air temper- ature at the delivery point; servicing of cooling system with a solution of ethylene glycol and water in equal parts by volume and cycling
13、 of the dmp body arid components. for driving on left side of road. When right-hand drive is specified, headlights shall be adjusted 3.7 Workmanship. Defective components or parts and assemblies which have been repaired or modified to overcone deficiencies shall not be furnished. bolted, and riveted
14、 construction utilized shaU be in accordance with the highest standards of the industry. Welded, 4. QUALITY ASSURANCE PROVISIONS 4.1 Contractors inspection. Unless otherwise specified in the contract or purchase order, the supplier is responsible for the perfonaance of ail inspection requirements as
15、 specified herein. Except as otherwise specified, the supplier may utilize his own facilities or any cormnercia laboratory acceptable to the Government. ions set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requlrements.
16、 The Government reserves the right to perform any of the inspect- 4.2 Government verification. Quality assurance operations performed by the contractor will be subject to Government verification at unscheduled intervals. Verification will consist of observation of the operations to determine that pr
17、actices, methods, and procedures of the contractors inspection are being properly applied, Failure of the contractor to promptly correct product deficiencies discovered shall 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-62033 (MO) A be ca
18、use for suspension of acceptance until correction has been made or until con- formance of product to specification criteria ks been demonstrated. 4.3 First production vehicle inspection. 4.3.1 The first production vehicle produced under the contrect shall be inspected by the contractor at his plant
19、under the direction and in the presence of Goverment representatives. vehicle conformity with the contract. shall not constitute a waiver by the Governent of its rights under the provisions of the contract. 4.3.2 The first production vehicle shall be weighed to determine curb weight and distribution
20、 of curb weight on front and rear axle. front and rear axle will be computed using the curb weight, the operator weight at 175 pounds, and the ptlykEld, wfO?dy distributed over the vehicle load area, to provide the specified GVW. Calculated imposed loads on front and rear axle will be utilized to as
21、certain that the suspension, axles and tires furnished ere of adequate capacity to meet contract requirements. payload) by the contractor to assure that the vehicle will operate in accordance with the contract requirements. inspection requirements on first production vehicle wlth payload, where such
22、 inspections are deemed necessary to assure the vehicle will operate in accordance with the con- tract requirements. The purpose of the inspection shall be to determine Acceptance of the first production vehicle The imposed loading on 4.3.3 The first production vehicle will be examined and road test
23、ed (less The Governent reserves the right to perform 4.3.4 Upon acceptance of the first production vehicle, it shail remain at the manufactwing facility as a production sample, and be the last vehicle shipped on the contract. condition for the duration of the contract. The confxactor shall maintain
24、the vehicle in a serviceable 4.3.5 Failure of the first production vehicle to meet requirements of the contract shall be cause for the Government to refuse acceptance of all vehicles on contract until corrective action has been taken. 4.4 Inspection of production vehicle. The contractors inspection
25、system shall as a minimum, assure that the vehicle conforms to the physical and dimensional requirements and is capable of meeting performance requirements contained herein, 5. PREPARATION FOR DELIVERY 5.1 Vehicle processir+ Vehicle shall be processed for shipment, from manufacturers plant to initia
26、l receiving activity, in accormce with manu- facturers stanar conmiercial practice, 12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-62033 23 U 7777706 OL777bL 2 6. NOTES 6.1 Intended use. for general administrative use by the Government in t
27、he performance of the maintenance and construction tasks. The vehicles covered by this specification are intended 6.2 Ordering data. Procurement documents should specify the following: la, custodians : Az - MO Title, number, and date of this specification. Heavy-duty cooling system, if required (see
28、 3.1.1.1) . Wdercoating, if required ( see 3.1 . 1 . 3) . Treatment and painting requirements (see 3.1.1.4) . Marking requirements (see 3.1.1.5). Power plant heaters, if required (see 3.4.1.3). Lighting socket and cable, if required (see 3.4.2.4.2). Positive-traction or limited-slip differential, if
29、 required (see 3.4.9.1) . Spare wheel or rim if required (see 3.4.10.3). Spare tire, if required (see 3.4.10.3.1). Number of pairs of seat belts, if more than two required (see 3.4.12). If tools &re not required (see 3.4.16). Right hand drive, if required (see 3.4.18). Pintle assembly, if required (see 3.1.1.8). Preparing activity : Project No. 23X)-A$XI DW - MO(ATAC) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
