1、 7 -= - HIL-T-62L02F 23 I 9999906 0497847 4 II - - -_ - Beneficial commenta (recommendations, additions, deletiona) and any pertinent data which may be of use in improving thia document should be addressed to: US Atmy Tank-Automotive Command, AT“: AMSTA-UED, Warren, MI 48397-5000, by using the self-
2、addressed Standardization MIL-T-62102F - SUPERCEDING MILT-62102E 9 March 1987 MILITARY SPECIFICATION * TRUCK TRAcIy)zs: SEMImIUR SPOTTER, WITH HALF CAB, DIESEL AND GASOLINE ENGINE DRIVEN, 32,000 GVW, 55,000 GCW AND 44,000 GVW, 90,000 Gcw, 4x2, MODIFIED COMMERCIAL This specification is approved for u
3、se by all kpartments arid Agencies of the Department of distribution is unlimited. I Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. NIL-T-62102F 23 m 7999906 0497848 b m 1 MIL-T-62102F . The following a. *
4、2.1.1 -s. standards. specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense index of Specifications and Standards WDISS) and supplement
5、thereto, cited in the solicitation (see 6.2) - SPEC1 PICATIONS .PEDERAL W -B- 131 W-F-800 MI LITffiY MIL-P-514 MIL-T-83133 STANiMFtS FEDERAL PED-STD-297 - Battery, Storage: Vehicular, Ignition. - Fuel Oil, Diesel. Lighting and Starting- - Plates, Identification, - Turbine Fuei. kvtion. - Twbine Fuel
6、, Aviatian. Marking El&;. JP-5. JP-8 - - Rustproofing of Commerc Vehicles. Instruction anci GrL-idps JI;-4 aid. Kerosene Type. Grade al (. Non$act ical ) MILITARY MIL-STD-1223 - Nontactical Wheeled Vehicles Treatment, Painting, Identification Marking, and Data Plate Standards. Capacity. Manual Relea
7、se- Intervehicular, Sa-Volt, Waterproof. - Connector, Receptacle, Electrical - 12 Contact, Intemrehicular. 28-Volt. Waterproof. MC511 18 - Pintle Assembly, Towing - 40.000 Lbs. MS75020 - Connector, Plug, Electrical - 12-Contact, MS7502 1 (Unless otherwise indicated, copies of federal and military sp
8、ecifications, standards, and handooka are available from the Naval Publications and Pomns Center, Military Specifications and Standards, Bldg. 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094). * 2-1.2 -ent daumeE. System Tubinc (Ticif Protection (WD adopted). adopted 1. anci Semitrailers ( LOD a
9、dopted 1. adogxed ) . Truck-Trailer Connections. Diesel. - Seven-Conductor Jacketed Cable for - Engine Power Test Code - Spark lgnition and (Application for copies of CAE publications should be addressed to SA. Inc-, 400 Commonwealth Drive, Warrendale, PA 15096.) THE TIRE AND RIM ASSOCIATION, INC. Y
10、ear Book - * (Application for copies of Tire and Rim Association publications should be addressed to The Tire and Rim Association, Inc., 175 Montrose West Ave., Copley, OH 44321.) * from the organizations that prepare or distribute the document. documents also may be available in or through librarie
11、s or other informational services). (Non-Government standards and other publications are normally available These * 2.3 Qrder of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this docum
12、ent. however, supersedes applicable laws and regulations unless a specific exemption has been obtained- 3. REQUIREMENTS $. 3.1 Standard vehicle and accessories . Except as specified in 3.1.1 through 3.1.1.9, the vehicle, components, assemblies, and accessories to be delivered under the contract shal
13、l be standard or optional items, which meet or exceed the requirements of this specification. Except as specified in 4 Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I MIL-T-62102F 3.1.1 through 3.1.1.9, no r
14、emoval, substitution or alteration of the chassis manufacturers standard or opt.iona1 chassis model components shall be made. All chassis items shall be as represented in the chasss manufacturers technical data book. repreaented in the body and equipment manufacturere technical data- Technical data
15、shall be limited to specifications and technical material, identical to that furnished Lo the authorized company representatives for selection of vehicle models and components, and shall be available to the. engineering offices of the procuring activity, prior to delivery of the items. The chassis m
16、odel furnished shall be not older than the chassis manufacturers current model on the date of invitation for bids. Special bodiea or mounted equipment shall be as 3.1.1 Smcial ream - In addition to the standard vehicle and c.ornpments specified in 3.1, the vehicle shall be furnished with special equ
17、ipnsnt as specified herein. *- 3.1 1, l. bcamnt and 3- - The vehicle shall be trestt.5 wd painted in accordance with MIL-STIl-1223. As specifieci, by the procuring activity for the appropriate military service (see 6.2). -,ne exterior ccicir shall be in accordance with MIL-STD-1223- * 3.1.1.2 2 . As
18、 specified by the procuring activity for the appropriate militany service (see 6.2), identification marking and data plates shall be in accordance with MIL-STD-1223. When specified (see 6.2), concealed markings shall be furnished- 3.1.1.3 BystpronfinE! - When specified (see 6.2), the vehicle shall b
19、e rustproofed in accordance with FED-STD-297. When specified (see 6-2), tropical rustproofing in accordance with FKbCTD-297 shall be furnished. 3.1.1.4 . The drain plug for the rear axle differential shall be of the permanent magnet type. 3.1.1.5 Towiiur de- . Not less than two hooks, loops, pins, o
20、r a center mounted eye for towing the vehicle shall be furnished on the front of the vehicle and not lesa than two hooks, loops, or pins for towing the vehicle shall be furnished on the rear of the vehicle. shall be frame mounted. Front towing devices shall have a total capacity of not less than 600
21、00 pounda and rear towing devices shall have a total capacity of not less than 35,000 pounds. a pintle, safety chain attachment devices, a lighting receptacle and associated reinforcements and wiring shall be installed on the rear of the vehicle. The pintle shall be of the rotating type conforming t
22、o MS51118. “he pintle shall be installed on the chassis frame with reinforcements to transfer a vertical tongue load of not less than 4,000 pounds and a horizontal drawbar load of not less than 40,000 pounds directly to the The towing devices 3-1-1.6 Trailer tn- . A trailer towing package consisting
23、 of 5 Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-62102F chassis rails. inches forward of the rearmost part of the vehicle. Two trailer aafety chain attachment devices, one adjacent to each side of t
24、he pintle, shall be provided. less than 40,000 pounds and shall be capable of accommodating a standard grab hook (4-9/16 inches wide, 1-3/16 inches thick, 25/32-inch throat width) fou. a S/e-inch chain. conductors connected and color coded aa specified therein, shall be mounted in a readily accessib
25、le location near the pintle. The rearmost portion of the pintle shall be not more than 4 Each attachment device ahall provide an ultimate strength of not A lighting receptacle, conforming to SA6 J560 with its 3-1-1-7 Fronf,Lfs and a full complement of fuel, ldricants and coolant. . Gross combination
26、 weight (W shall 3.2.6 ween 12 aici 15 niph fer size 44. Conformance to geared sed SpciLied- shall be determined by calculating in accordance with the following formula: Maximum geared speed (mph)= Governed speed Ir Regulations 393.12, 393.13, 393.19, 393-20 and 393.22 through 393.26(dl. 3.4.2.5 - T
27、urn signal lamps shall conform to SAE 5588. perating units shall conform to CAE 5589 class A and shall be mounted on the steering column- Signal units shall be visible and audible in combination with the towed vehicle and shall be visible when not in combination with the towed vehicle. Turn signal o
28、perating units shall have a visible and audible type flash indicator. 3.4-2.6 -ine cable - A Semitrailer lighting cable conforming to SAE 51067 and incorporating a connector conforming to SAE J560 on the semitrailer end shall be provided. The cable shall be coiled and shall have an extended length o
29、f not less than 110 inches- The SA6 J560 connector shall include a grip for withdrawing from the semitrailer receptacle. Stowage for the cable shall be provided by means of hook and hanging loop or protective holding bracket. When hook and loop method is used, the cable shall be furnished with a han
30、ging loop, so attached as to insure that the plug is pointed down when the cable is stowed in the hook provided on the rear of the truck tractor cab or on a pogo stick type hose tender. The protective bracket, when furnished, shall be mounted at the rear of the cab, below the roof line, and shall ho
31、ld the cable plug within the bracket housing to preclude entrance of weather within the terminals- 3.4.2.7 cible . A trailer lighting cable, conforming to GAE 51067, shall be furnished for use with the lighting receptacle specified in 3.1.1.7. The cable shall be not less than 110 inches long and bot
32、h ends of the cable shall be equipped with a round plug conforming to SAE J560. plugs shall be equipped with a grip or withdrawing from the connector sockets. compartment- The The cable shall be packaged and stowed in the vehicle tool il Licensed by Information Handling ServicesProvided by IHSNot fo
33、r ResaleNo reproduction or networking permitted without license from IHS-,-,-i MIL-T-62102F 23 .99999Ob 0497858 9 -i i Reserve capacity Cold cranking (aIn?E.req ) MI L-T-62 102F 3.4.2.9.1 Two 12-volt batteries with a combined capacity of at least 40 ampere-hours at a 20-hour rate or one 24-volt batt
34、ery with at least 20 ampere-hours capacity at a 20-hour rate; (b) (c) A voltage regulating device: (d) An ammeter, mounted on the instrument panel. - The vehicle shall be 3-4.2.10 iiaduu svnta . The erhaust system shall conform to Federal Motor Csryier Safety Xeg-dation 333.83. ?he e-.-.aust sys:,em
35、. wkn stacked, sliali b+ furnisheci with a heat snield ana a hhiged rain cap. vehicles the tail pipe shall be stacked on the curbcj.de of the engine transversely in line with the rear half of the cab, exhaust system atove the body sheet metal shall be fully enclosed by a heat shield. system which pr
36、oject to the rear of the cab shall be provided with a cover plate. spilled fuel from coming into contact with the exhaust system. A spark arrester shall be furnished, except on turbocharged engines. The spark arrester shall have an 80 percent arresting efficiency when rated in accordance with CAE 53
37、50- On diesel engine ariven All portions of the On gasoline engine driven vehicles, all portions of the exhaut The cover plate shall form a shield that will shed fluids. precluding . An automatic transmission shall be The transmission shall * 3.4.5 provided. to the maximum torque delivered by the en
38、gine. include a hydraulic torque converter and not lees than five forward gear ratios. four forward gear ratios without movement of the selector. shall be provided with a power takeoff opening. hydraulic retarder shall be provided. takeoff shall be of a rated capacity to operate powered equiment. Co
39、ntrole to operate the power takeoff shall be located in the truck cab accessible to the seated driver. A caution plate or decal reading “D NOT OPERATE VEHICLE AT HIGHWAY SPEEDS WITH PWER TAKEOFF ENGAGED“ ishall be provided and installed so as to be readily visible to the aeated driver. Input torque
40、capacity of the transmission shall be at least equal Normal driving range aelector position shall provide not less than Tbe transmisaion When speoiied (see 6.2), a 3.4-5.1 Power takedf. A power takeoff shall be provided. The power 3.4-6 hiveline cm . Driveline components shall be adequate to transmi
41、t the maximum delivered torque of the engine, as developed through the maximum gear reduction. similar to that epecified for buses by Federal Motor Carrier Safety Regulation 393.89. The drive shaft shall be protected in a manner 13 Licensed by Information Handling ServicesProvided by IHSNot for Resa
42、leNo reproduction or networking permitted without license from IHS-,-,-3.4.7 Erame. Chassi0 frame shall be the manufacturers standard for the vehicle furnished. resisting bending mment to at least equal the loads imposed under the specified operating conditions with vehicle loaded ta specified cfvw.
43、 When frame reinforcements are required to meet the specified loada. the reinforcements shall extend at least from the rear of the front-suspensioh, rear hanger bracket to the front of the rear-spring, front hanger bracket, hmnnembers shall be provided at least reazward of the tfansmission and at th
44、e rear. “he chaasia frame rails shall be cut off immediately to the rear cI.j,:ie rmip -preser,t;irg a c.int-iriucus slcq? fcpi. e. sernitraiier approach, anci proviciecl with a ni*ais ir “bolt-on“ attacimmt, nw the vehicle chassis frame- The fifth wheel aicl its mounting structure shall have a desi
45、gn capacity to withstand a drawbar puli of 60,000 pounds without residual deformation to the mounting, fifth wheei OF the truck tractor structure. Ille fifth wheel installation shall conform to 3.5.1. When a conventional cab is The pogo stick type hose tender shall be mounted on the The air operated
46、 fifth wheel * 3-6.1 Bir omratedairft fifth The air operated air lift fifth wheel shall be furnished and installed with at least the fol1uwir.g: Air reservoir tank(s), not less than 7.4 cubic feet total capacity, equipped with drain, safety and check valves between compresscr anci tal+. Air compress
47、or, not less than 12 cfm, air or water cooled, engine driven and engine lubricated. wiloader-head type. Automatic moisture ejection valve Two air starter valves to emit and expel air from the reservoir tank. to the air bellows Three-way valve, for raising, lowering or holding the fifth wheel in any
48、desired position. The valve control shall be mounted on the truck tractor instrument panel in an accessible location for the driver, when in a seated position. with a guard to prevent accidental activation Snubbers to eliminate spring deflection Pneumatic system to open and lock the CAE 5700 kingpin
49、, operable from the truck tractor instrument panel Manual secondary lock to prevent accidental uncoupling. The control shall be provided 3.6.2 Fifth wheel (air owrW . The fifth wheel shall be of the fore and aft rocking type, with a 36-inch cast steel coupler plate with beveled approach orks. Carrier Safety Regulations 393,70(b). The fifth wheel assembly shall conform to Federal Motor Licensed by Information Handling ServicesProvided by IHSNot for
