1、T MIL-T-6231bB 23 m 999990b 0507819 7 m I NOT MEASUREMENT SENSITIVE I I I MIL-T-62316B(AT) - SUPERCEDING . MIL-T-62316AAT) 30 March 1982 MILITARY SPECIFICATION TRUCK, VAN, PANEL: CALIBRATION AND REPAIR: 3900 KILOGRAMS (8,600 POUNDS) GW, 4x2, MODIFIED COMMERCIAL This specification is approved for use
2、 by the US Army Tank- Automotive Command, Department of the Army, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Sm- This specification covers diesel or gasoline engine driven, four-wheel, two-rear wheel drive, forward control type commercial pane
3、l trucks, with cabinetry and shelving. weight (GVW) of 3900 kilograms (kg) (8,600 pounds). this specification are commercial items which are warranted by the manufacturer as specified in acquisition documents. The truck has a minimum gross vehicle Vehicles procured under See figures 1 through 5. Ben
4、eficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: US Army Tank-Automotive Command, ATTN: AMSTA-UED, Warren, MI 48397-5000, by using the self-addressed Standardization Document Improvement Proposal (D
5、D Form 1426) appearing at the end of this document or by letter. AMSC NIA I FSC-2320 I - Approved for public release; distribution is unlimited I a Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-T-623LbB 23 W 9993906 0507820 3 W MI L-T-623 l6B
6、( AT ) 2. APPLICABLE WCMENTS 2 1 Goverment docWent,-, CI . * 2.1.1. Mfications. stm and handbook. The following agicificationa, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issu
7、e of the Department of Defense Index of Specifications and Standards DDISS) and supplement thereto, cited in the solicitation (see 6.2). SPEC1 FICATIONS FEPERAL W-3- 131 - Battery, Storage: Vehicular, Ignition, Lighting and Starting, e W-F-800 - Fuel Oil, Diesel, W-A- 161 7 - Adhesive, Rubber Base,
8、General Purpose. MI LI TARY * MI L-P-514 - Plates, Identification, Instruction and * MIL-T-5624 - Turbine Fuel, Aviation, JP-4 and JP-5. Marking, Blank. MIL-P-26514 - Polyurethane Foam, Rigid or Flexible, For MIL-B-46176 - Brake Fluid, Silicone, Automotive All Packaging. Neather, Operational and Pre
9、servative. JP-R . yr MIL-T-83123 - Turbine Fuel, Aviation, Kerosene Type, Grade STANDARDS FEDERAL PED-STD-297 - Rustproofing of Commercial (Nontactical) FED- STD- 595 - Colors. Vehicles. MI Li TARY MIL-STD-209 - Slinging and Tie Down Provisions For Lifting and Tying Down Military Equipment. Painting
10、, Identification Marking and Data Plate Standards. * MIL-STD-1223 - Nontactical Wheeled Vehicles Treatment, MS 51939 - Loop, Strap Fastener (Footmans Loop). * (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Naval Publication
11、s and Forms Center, Military Specifications and Standards, Bldg. 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-bZ31bB 23 m 99999Ob O507821 5 m * 2.1.2 Mer Government dmunentn. dru- . The
12、following other Government documents, drawings, and publications form a part of this document to the extent specified herein. the issues are those cited in the solicitation. Unless otherwise specified, * PEPARTMENT OF DEFENSE (DOD) Department of Defense Index of Specifications and Standards (DODISS)
13、. (Copies of the DODISS are available on a yearly subscription basis either from the Government Printing Office for hard copy? or microfiche copies are available from the Director, Navy Publication and Printing Service Office, 700 Robbins Avenue, Philadelphia, PA 19111-5093,) * DEPARTMENT OF TWSPORT
14、ATION (DOT) Federal Motor Carrier Safety Regulations. Federal Motor Vehicle Safety Standards. (Application for copies of DoT publications should reference the Code of Federal Regulations, 49 CFR, and the Federal Register, and should be addressed to the Superintendent of Documents, U.S. Government Pr
15、inting Office, Washington, D.C. 20402.) ENVIRONMENTAL PROTECTION AGENCY (EPA) Control of Air Pollution from New Motor Vehicles and New Motor Vehicle Engines - (Application for copies of EPA publications should reference the Code of Federal Regulations, 40 CFR, and the Federal Register and should be
16、addressed to the Superintendent of Documents, U.S. Government Printing Office, Washington, D.C. 20402.) DRANINGS 7921089 ,: 792 109 1 - Container Assembly (Code 18876) - Container Weldment (Code 18876) Mi * (Application for copies of Drawings should be addressed to U.S. Army sile Command, ATTN: DRSM
17、I-MSS, Redstone Arsenal, AL 35898.) 2.2 Non - Government -oub;Licaticrm . this document to the extent specified herein. the issues of the documents which are DoD adopted are those listed in the issue of the DODISS cited in the solicitation. the issues of documents not listed in the DODISS are the is
18、sues of the documents cited in the solicitation (see 6.2). The following documents form a part of Unless otherwise specified, Unless otherwise specified, * THE EUROPEAN TYRE AND RIM TECHNICAL ORGANISATION (ETRTO) Standards Manual 3 Provided by IHSNot for ResaleNo reproduction or networking permitted
19、 without license from IHS-,-,-MIL-T-b23LbB 23 999990b O507822 7 (Application for copies of ETRTO publications should be addressed to the European Tyre and Rim Technical Organisation, 32, Avenue Brmgmann, 1060 Brussels, Belgium. * NATIONAL FIRE PROTECTION ASSOCIATION, (NPPA) NFPA No. 70 - National El
20、ectric Code . (Application for copies of NFPA publications should be addressed to the National Fire Protection Association, Batterymarch Park, Quincy, MA 02269. SAK, INC. CAE Standards and Recommended Practices 5537 - Storage Batteries. 5551 - Limits and Methods of Measurement of Radio Interference
21、Characteristics of Vehicles and Devices (30-1000 MHz). - Rear Wheel Splash and Stone Throw Protection (DoD adopted) - - Engine Power Test Code - Spark Ignition and Diesel - 5682 * 51349 ” (Application for copies of CAE publications should be addressed to SAE, INC., 400 Commonwealth Drive, Warrendale
22、, PA 15096.) THE TIRE AND RIM ASSOCIATION, INC. Year Book - k: be addressed to the Tire and Rim Association, Inc., 175 Montrose West Ave., Copley, OH 44321.) (Application for copies of Tire and Rim Association publications should * from the organizations that prepare or distribute the document. docu
23、ments also may be available in or through libraries or other informational services.) (Non-Government standards and other publications are normally available These L X 2.3 Order of Drecedem. In the event of a conflict between the text of this document and the references cited herein, the text of thi
24、s document takes precedence. Nothing in this document, however, suprsedes applicable laws and regulations unless a spacific exemption has been obtained. 3. REQUIREMENTS si: 3.1 StS - Except as spcified in 3.1.1 through 3.1.1.9, the vehicle, components, assemblies, and accessories to be delivered und
25、er the contract shall be standard or optional items, which meet or exceed the requirements of this specification. 3.1.1 through 3.1.1.9, no removal, substitution or alteration of the van manufacturers standard or optional chassis model components shall be made. Except as specified in 4 Provided by I
26、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-623LbB 23 = 9999906 0507823 9 = All chassis items shall be as represented in the chassis manufacturers technical data book. represented in the body and equipment manufacturers technical data. Ckbinets and shel
27、ving shall be as specified herein. limited to specifications and technical material, identical to that furnished to the authorized company representatives for selection of vehicle models and components, and shall be available to the engineering offices of the procuring activity, prior to delivery of
28、 the items. The chassis model furnished shall be not older than the chassis manufacturers current model on the. date of invitation for bids. Special bodies or mounted equipment shall be as Technical data shall he 3.1-1 ing - When specified (see 8-21, the vehicle shall be rustproofed in accordance wi
29、th FED-STD-297. tropical rustproofiizg in accordance with FED-STD-297 shall be furnished: When specified (see 6-21, 3.1.1.4 TowiriEs devicefi - Towing devices consisting of two hooks, loops, eyes or pins or the manufacturers single center mounted eye or pin shall be mounted on the front of the vehic
30、le. When specified (see 6.2), in addition, towing devices shall be mounted on the rear of the vehicle. devices shall be frame rail mounted or reinforced back to each frame rail. All towing * 3.1.1.5 Lifting and tiedam attacb-. - When specified (see 6.2), the vehicle shall be equipped with lifting an
31、d tie down attachments. Lifting and tie down attachments shall conform to type II of MIL-STD-209. MIL-STD-209, wherever “maximum shipping weight (MSN)“ occurs, replace it with “curb weight.“ A transportation plate conforming to composition A (class 1 or 2) or composition C of MIL-P-514 shall be prov
32、ided. The transportation plate shall be inscribed with a diagram showing the lifting attachments and proposed lifting slings, the capacity of each attachment, and the required length and size of each sling cable. center cf gravity shall be provided on the transportation plate. Tie down In A silhouet
33、te of the vehicle showing the 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-623LbB 23 m 999990b 0507824 O m MIL-T-GZ3lGB(AT) attachments shall be identified by stenciling or other suitable marking. down markings shall clearly indicate that
34、the attachments are intended for t.he tie down of the equipment on the carrier. Tie 3.1.1.6 Drain QU. Drain plugs installed in manual transmissions and rear axles shall be of the permanent. magnet type. $ 3.1.1.7 Uone brake fh u$. When specified (see 6.21, and if available as the manufacturers stand
35、ard or- optional brake fluid, brake fluid conforming to MIL-E-46176 shall be provided in the hydraulic brake system. A decal or plate shall be placed near the master cylinder stating “CAUTION: USE SILIOME BRAKE PLUID ONLY, MIL-B-46176.“ t * i3.1 1.8 -sh and stone throw Drotectinn . Vans shall have r
36、igid the rear wheels. A metal strip not less than 3.2 millimeters (mm) (0.125 inch) thick and not. less than 25 mm (1. inch) wide, extending the entire width of the md flap, shall be installed to prevent the bolt heads or bolt nuts from damaging the mud flap. As an alternate method of attaching t.he
37、 mud flaps, tabs or clips with minimum surface contact dimensions of 25 mm (1 inch) high.by 32 mn (1.25 inch) wide by 2.4 rnm (0.094 inch) thick, shall be furnished at each bolt. front and rear, shall conform to the rear wheel splash and stone throw protection provisions of SAE J682. 4: 3.1.1.9 Brak
38、e 1ikL.s . At least one pair of brake lights shall override the four-way emergency flasher or the two systems shall be independent of sacn other. accommodate this requirement shall not compromise. conformance to any Federal Motor Carrier Safety Regulation referenced herein or to any Federal Motor Ve
39、hicle Safety Standard. If additional lights are added to the vehicle, the Lights shall be selected from the chassis manufacturers standard matching hardware - sgi.ach shields ahead of the rear wheels and rubber mud flaps to the rear of 1 Ali splash shield and mud flap installations, Modifications to
40、 the manufacturers standard product to 3-2.1 Federal Motor Ve.hicle Safetv Standards . The vehicle and furnished accessories shall comply with all Federal Motor Vehicle Safety Standards in effect on the date of manufacture. *- 3.2.2 torquing of all fasteners to manufacturers recommendathnc; adjustme
41、nt of engins, electrical and brake systems; filling and charging uf battery; alinement; of front wheels; inflation of all. tires; complete lubrication of chassis, engine, and running gear, with grades of lubricants ecornmended for the ambient air temperature at the delivery point; servicing of cooli
42、ng system with a solution of ethylene glycol type antifreeze and water in equal parts by volime; and Servicing of the windshield wauher reservoir with water and appropriate additives; tactile examination of the cabinets, shelves and inte.rior componenks. :k 3.5.1. meter plug-in cabinet, spare parts
43、cabinet and the two containers shall be marked as follcms: I (a) Shelving reapward of the bench seat, each shelf mark: “136 kg (b) !,c) (ci) Container (2) 115 kg (250 pounds) each. I (300 gxxmds) capacity“ in a visible location Meter plug-in cabinet on the exterior of one door, mark: (SOO pcuncis) c
44、apacity“ Spare parts cabinet on the exterior of one. door, mark: (ZO# pound) capacity“ “91 kg “91 kg The above marked payload capacities are payloads the user will place on the shelves rearward of the bench seat, in the cabinets and the weight of the two containers placed between the cabinets on the
45、 floor. cabinets shall have a design payload capacity as specified in their respective paragraphs, to provide structural integrity. The shelves and 3 Ei. 4 1 Calibrat ion eaubent shelf fru - A calibration equipnent shelf framing with two shelves shall be provided behind the bench seat (see figures 2
46、, 3 and 4), and shall have oyen front and top. rnmnted facing the rear of the vehicle cargo area. minimum dimension of 810 mm (32 inches) plus 25 mm (1 inch), minus O mm (0 inches) in height and 635 nun (25 inches) in depth. The width shall be the maximum attainable between the van walls and dependi
47、ng upon location and dimensions of the wheelwells. Shelving frame shall be constructed of steel Qr aluminum of adequate gage and shall be reinforced to support the maximum design load of 272 kg (600 pounds). The area above the top of the framing at the back shall have 13 mm (0.50 inch) flattened exp
48、anded metal installed from the top of the framing to the ceiling and close off all cavities between the framing, vehicle walls, and the ceiling. at tiit- back, shall have a solid full width and height metal panel to enclose the back of the two shelves (see 3.5.4.1.1). The expanded metal edge that is
49、 adjacent to the metal panel shall have an edge molding. and the metal panel shall be so fitted as t,o enclose all cavities between the vehicle floor, side walls and ceiling. All installation shall be accomplished from the cargo area to prevent items being removed from the crew area by personnel and unauthorized personnel. The shelves shall be Frame shall have a The area below the expanded metal The expanded metal 3.5.4.1.1 Shelviw . The shelving unit s
