1、NIL-T-625LA 23 SSSSSOb OY95LBY 5 Nur MEASUREMENT SENSITIVE MIL-T-6251BA - SUPERSEDING MI L-T- 625 18 18 December 1985 MILITARY SPECIFICATION TRUCKS, MAINTENANCE: WITH 9 TO 37 METERS (30 TO 120 FOOT) MULTI-WSITION AERIAL PLATFORM, MODIFIED COMMERCIAL This specification is approved for use by all depa
2、rtments and agencies of the Department of Defense. 1. SCOPE 1.1 Scnm. This specification covers diesel and gasoline engine driven, four-wheel, two-rear-wheel drive; four-wheel, four-wheel drive; and six-wheel, four-rear-wheel drive trucks having minimum gross vehicle weights (GVW) of 6800 kilograms
3、(kg) (15,000) to 22 700 kg (50,000 pounds), equipped with maintenance bodies and 9 to 37 meters (m) (30 to 120 foot) multi- position, articulating, boom type aerial platforms- Vehicles procured under this specification are commercial items which are warranted by the manufacturer as specified in acqu
4、isition documents. - 1-2 ClaBslfication sizes shown in table I, as specified (see 6.2): The vehicle shall be one of the types, classes and ubliCatiom - The following other Government documents, drawings and publications form a part of this specification to the extent specified herein. specified, the
5、 issues shall be those in effect on the date of the solicitation. Unless otherwise * DEPARTMENT OF DEFENSE Department of Defense Index of Specifications and Standards (WD1SS)- (Copies of the DODISS are available. on a yearly subscription basis either from the Government Printing Office for hard copy
6、, or microfiche copies are available from the Director, Navy Publication and Printing Service Office, 700 Robbins Avenue, Philadelphia, PA 19111-5093.) DEPARTMENT OF TRANSPORTATION (DoT) Federal Motor Carrier Safety Regulations. Federal Motor Vehicle Safety Standards. (Application for copies of DOT
7、publications should reference the Code of Federal Regulations, 49 CFR, and the Federal Register, and should be addressed to the Superintendent of Documents, U-S. Government Printing Office, Washington, D.C. 20402.) 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without licens
8、e from IHS-,-,-I I e b I. I t MIL-T-62518A 23 9999906 0495188 2 MIL-T-62518A ENVIRONMENTAL PROTECTION AGENCY (EPA) Control of Air Pollution from New Motor Vehicles and New Motor Vehicle Engines - Noise Emission Standards for Transportation Equipment - Medium and Heavy Trucks- (Application for copies
9、 of EPA publications should reference the Code of Federal Regulations, 40 CER, and the Federal Register and should be addressed to the Superintendent of Documents, U-S- Government Printing Office, Washington, D.C. 20402.) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION (OSHA) Occupational Safety and H
10、ealth Standards. 1926.556 - Aerial Lifts. (Application for copies of OSHA publications should reference the Code of Federal Regulations, Title 29, and should be addressed to the Superintendent of Documents, U.S. Government Printing Office, Washington, D.C. 20402.) * 2-2 b - Goverriment Dubficatiom -
11、 The following documents form a part of this specification to the extent specified herein. syecified, the issues of the documents which are indicated as DUD adopted shall be those listed in the issue of the DoDISS specified in the solicitation- Unless otherwise specified, the issnes of documents not
12、 listed in the DoDISS shall be the issue of the non-Government document which is current on the date of the solicitation (see 6.2)- Unless otherwise AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI) ANSI A92.2 - American National Standard for Vehicle Mounted Elevating and Rotating Aerial Devices - (Appli
13、cation for copies of ANSI publications should be addressed to the American National Standards Institute, Inc., 1430 Broadway, New York, NY 10018 ) * AMERICAN S0CIE;TY FOR TESTING AND MATERIALS (ASTM) ASTM A 53 - Pipe, Steel, Black and Hot-Dipped Zinc-Coated (Galvanized) Welded and Seamless, for Ordi
14、nary Uses (DUD adopted). - Standard Method of Salt Spray (Fog) Testing (DoD adopted). - Standard Specification for Low Silicate Etkiylene Glycol Base Engine Coolant for Heavy Duty Engines Requiring an Initial Charge of Supplemental Coolant Additive. ASTM B 117 ASTM D 4985 5 Provided by IHSNot for Re
15、saleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-62518A 23 I 9999906 0495389 4 MIL-T-62518A (Application for copie3 of ASTM gublications should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) * THE EUROPEAN TYRE
16、 AND RIM TECHNICAL ORGANISATION (ETRTO) Standards Manual (Application for copies of ETRTO publications should be addressed to the European Tyre and Rim Technical Organisation, 32, Avenue Brugmann, 1060 Brussels, Belgium.) NATIONAL FIRE PROTECTION ASSOCIATION (NFPA) NFPA No. 70 - National Electric Co
17、de. (Application for copies of NFPA publications should be addressed to the National Fire Protection Association, Batterymarch Park, Quincy, MA 02269.) CAE, INC. 5318 5350 5537 J55 1 5560 5588 5589 JO82 5683 5688 5704 5706 5844 51067 51292 Ji349 - Air Brake Gladhand Service (Control) and Emergency (
18、Supply) Line Couplers - Trucks, Truck-Tractors, and Trailers (DoD adopted). Size Engines (bD adopted). - Spark Arrester Test Procedure for Medium - Storage Batteries. - Performance Levels and Methods of Measurement of Electromagnetic Radiation from Vehicles and Devices (30-1000 MHz). - Seven-Conduct
19、or Electrical Connector for Truck-Trailer Jumper Cable. - Turn Signal Lamps. - Turn Signal Switch. - Rear Wheel Splash and Stone Throw Protection (DoD adopted). - Tire Chain Clearance - Trucks, Buses, and Combinations of Vehicles (DoD adopted). - Truck Ability Prediction Procedure (DoD adopted). - O
20、penings for Six- and Eight-Bolt Truck Transmission Mounted Power Take-offs (DoD adopted) - adapted). Truck-Trailer Connections. and Motor Coach Wiring. Diesel. - Rating of Winches. - Nonmetallic Air Brake System Tubing (ROD - Seven-Conductor Jacketed Cable for - Automobile, Truck, Truck-Tractor, Tra
21、iler - Engine Power Test Code - Spark Ignition and 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I. MIL-T-bZ518A 23 W 9999906 0495170 O MIL-T-62518A (Application for copies of SAE publications should be addressed to SAE, Inc., 400 Commonwealth Dr
22、ive, Warrendale, PA 15096.) THE TIRE AND RIM ASSOCIATION, INC. Year Book * (Application for copies of Tire and Rim Association publications should be addressed to The Tire and Rim Association, Inc., 175 Montrose West Ave., Copley, OH 44321.) * from the organizations that prepare or distribute the do
23、cuments. documents also may be available in or through libraries or other informational services.) (Non-Government standards and other publications are normally available These * 2.3 Qrder of rrecea. In the event of a conflict between the text of this document and the references cited herein, the te
24、xt of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS * 3.1 Standardle and nnnnnmries - Except as specified in 3.1.1 through 3.1.1.15, the vehicles, components and accessories
25、 to be delivered under the contract as further identified and qualified in the product experience clause of this solicitation shall be standard or optional items sold commercially to the public which meet or exceed the requirements of this specification. Except as specified in 3.1.1 through 3.1.1.15
26、, no removal, substitution or alteration of the chassis manufacturers standard or optional chassis model components shall be made. represented in the chassis manufacturers technical data book. bodies or mounted equipment shall be as represented in the body and equipment manufacturers technical data.
27、 Technical data shall be limited to specifications and technical material identical to that furnished to the authorized company representatives for selection of vehicle models and components, and shall be available to the engineering offices of the procuring activity, prior to delivery of the items.
28、 The chassis model furnished shall be not older than the chassis manufacturers current model on the date of invitation for bids. All chassis items shall be as Spcial 3.1.1 Smcial rea- . In addition to the standard vehicle and components specified in 3.1, the vehicle shall be furnished with special e
29、quipment as specified herein. i The vehicle shall be treated and * 3.1.1.1 painted in accordance with MIL-STD-1223. yellow, matching color chip No. 13538 of PED-STD-595. spiral wound booms and baskets need not be painted. The exterior color shall be gloss Extruded, molded or 7 Provided by IHSNot for
30、 ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-6251A 23 9999906 0495393 2 I MIL-T-62518A * 3.1.1.2 data . As specified by the procuring activity for the appropriate military service (see 8-21, identification marking and data plates shall be in accordance with MIL-S
31、TD-1223. When specified (see 6.2), concealed markings shall be furnished. * 3.1.1.2.1 Hazning Dlates . Warning plates shall be furnished and mounted in a conspicuous location near the lower and upper controls and in the drivers compartment. or composition C of MIL-P-514. appear on each of the three
32、plates: Plates shall conform to cornposition A (class 1 or 2) At least the following information shall WARNING AERIAL PLATFORM AND OUTRIGGERS MUST BE IN STOWED POSITION WILE VEHICLE IS BEING MOVED. RATED PLATFORM LOAD, HYDRAULIC OUTRIGGERS DOWN, NOT IN EXCESS OF POUNDS i INSPECT PLATFORM LEVELING SY
33、STFIM. MAXIMUM VOLTAGE BOOM AND PLATFORM WILL WITHSTAND .- WLTS AC. OVERALL TRAVEL HEIGHT WHEN BOOMS ARE IN STOWED POSITION VEHICLE SHALL NOT BE OPERATED IN WINDS IN EXCESS OF 30 MPH. BASMT LINER(S) MUST BE INSTALLED WHEN OPERATING ON OR NEAR ELECTRICAL LINES. W NOT PERMIT DIRECT CONTACT OF BASKET T
34、O GROUND WHEN OPERATING ON OR NEAR ELECTRICAL DISTRIBUTION LINES. MAXIMUM MNGITUDINAL INCLINE DEGREES - MAXIMUM TRANSVERSE SLOPE - DEGREES. BOOMS AND BASKET(S) MUST BE KEPT CLEAN AND FREE OF DAMPNESS. Do NOT DRILL HOLES IN BOOM OR BASKET TO DRAIN WATER, DUMP OUT WATER. USE ONLY RECOMMENDED TYPE OF H
35、YDRAULIC FLUID - WIRE BRAID HYDRAULIC HOSES MUST NOT BE USED ON OR NEAR ELECTRICAL LINES - * 3.1.1.2.2 . An instruction plate showing a schematic of all valves, valve controls and equipment, and complete warnings and instructions for operating the aerial equipment shall be fastened on the inside of
36、a curbside vertical cabinet door. Each control lever shall be marked with an instruction plate depicting the function of the control. Individual markings shall be adjacent to each control. to composition A (class 1 or 2) or composition C of MIL-P-514. Plates shall conform 3.1.1.2.3 Warning signa War
37、ning signs or labels, as recommended by the Manufacturers of Aerial Devices and Digger Derricks Council, shall be furnished and attached. 3.1.1.3 Rustdu. When epecified (see 6.2), the vehicle shall be rustproofed in accordance with FED-STD-297. tropical rustproofing in accordance with FED-STD-297 sh
38、all be furnished. When specified (see 6-21, R 1 I I Q 1 i 4 I I 5, c 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-625LBA 23 I 999990b 047.5172 4 MIL-T-62518A 3.1.1.4 . All drain plugs installed in manual transmissions, transfer case and re
39、ar axles shall be of the permanent magnet type. * 3.1.1.5 Towina devicai Not less than two hooks, loops, or pins, OF a single, center mounted towing eye, for towing the vehicle, shall be furnished on the front of the vehicle. or reinforced back to each frame rail. All towing devices shall be frame r
40、ail mounted * 3.1-1.6 . When apecified (see 6-22), a trailer towing package consisting of a pintle, safety chain attachment devices, a lighting receptacle and associated reinforcements and wiring shall be installed on the rear of the vehicle. The pintle shall be of the rotating type conforming to MS
41、 51118-1. frame with reinforcements to transfer a vertical tongue load of not less than 1815 kg (4,000 pounds) and a longitudinal drawbar load of not less than 178 kilonewtons (M) (40,000 pounds) directly to the chassis rails. The rearmost portion of the pintle shall be forward but not more than fou
42、r inches forward of the rearmost part of the vehicle. devices, one adjacent to each side of the pintle, shall be provided. Each attachment device shall provide an ultimate strength of not less than 8150 kg (18,000 pounds). standard grab hook (%i6 mm (4-9/16 inches) wide, 30 mm (1-3/16 inches) thick,
43、 19.8 mm (25/32-inch) throat width) for a 16 mm (5/8-inch) chain. The lighting receptacle, conforming to SAX J560 with its conductors connected and color coded as specified therein, shall be mounted in a readily accessible location near the pintle. The pintle shall be installed on the chassis Two tr
44、ailer safety chain attachment The attachent devices shall be capable of accommodating a 3.1.1.7 iw cable . A coiled electrical trailer cable conforming to SAE J1067 shall be furnished. 2800 mm (110 inches) long when fully extended. be equipped with a seven-circuit round plug conforming to SAE J560.
45、plugs shall be equipped with a grip for withdrawing from the connector sockets. compartment. The cable shall be not less than Both ends of the cable shall The . The cable shall be packaged and stowed in the vehicle tool 3.1.1.8 c0ndad.k When specified (see 6-21, the vehicle shall be provided with an
46、 electric trailer brake controller. The controller shall be installed in the truck cab amicl wired through the SAE J560 receptacle. The controller shall operate on the 12-volt electrical system of the truck and shall include load control, hand lever and accessories. * 3.1.1.9 ind stnne thrm motectio
47、a . Mud flaps shall be instabled to the rear of the rear wheels. A metal strip, not less than 3.2 millimeters (a) (0.125 inch) thick and not less than 25 mm (one inch) wide, extending the entire width of the mud flap, shall be installed to prevent bolt heads or bolt nuts from damaging the mud flap.
48、method of attaching the mud flaps, tabs or clips with minimum surface contact As an alternate Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_.- MIL-T-625LBA 23 7979906 0445393 b E dimensions of 25 mm (1 inch) high by 32 mm (1.25 inch) wide by 2.4 m
49、m (0.094 inch) thick shall be furnished at each bolt. Rear wheels shall be provided v7it.h splash and stone throw protection in accordance with CAE 5682. 3 - 1 - 1 - 10 Tir ive hubs - When specified for model 4x4, class A and B vehicles (see (5-2), manually operated drive hubs for disengaging the front wheels from the drive train shall be provided, except for vehicles equipped ith interaxle compensating devices between front and rear axles (see 3.4.5.1
