1、MIL-W-LIOBBK 83 7779706 0374773 T MIL-W-4088K 21 November 1988 SUPERSEDING MIL-W-4088 J 22 December 1981 MILITARY SPECIFICATION WEBBING, TEXTILE, WOVEN NYLON This specification is approved for use by all Departments and Agencies of the Department of Defense. . P 1. SCOPE 1.1 Scope. This specificatio
2、n covers untreated nylon webbing. 1.2 Classification. The nylon webbing shall be furnished in the type and class specified (see 1.2.1 and 6.2). The types shall conform to the require- ments of tables II and III as applicable for the class specified. Class 1 - Critical use (shuttle loom, nylon 6,6) C
3、lass IA - Critical use (shuttleless loom, nylon 6,6) Class 2 - Non-critical use (shuttle or Shuttleless loom, nylon 6 or nylon 6,6) 1.2.1 Class reference. When procurement documents referencing this specifi- cation do not specify the class of webbing, the requirements for class 1 (critical use) webb
4、ing shall apply. When class 2 webbing is specified, classes 1 and IA are acceptable alternates. I I Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: U. S. Army Natick Research, Development, and E
5、ngineering Center, Natick, MA O1 760-5014 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. I I AMSC N/A FSC 8305 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited THIS DOCUMENT
6、CONTAINS zb PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-W-40BBK 83 W 777790b 0374772 I W “ MIL-W-4088K 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1 .I Specifications, standards, and handbooks. The following specifi- cations, s
7、tandards, and handbooks form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the soli
8、citation. SPECIFICATION MILITARY MIL-P-43334 - Packaging of Textile Webbing and Tape STAN DARDS FEDERAL FED-STD-191 - Textile Test Methods MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection MIL-STD-1480 - Color Codes for Webbing, Textile; Manufacturers by Attributes Identification
9、(Copies of specifications, standards, and handbooks required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity.) 2 .I .2 Other Government documents, drawings, and publications. The following ot
10、her Government documents, drawings, and publications form a part of this specification to the extent specified herein. Unless otherwise specified, the issues shall be those in effect on the date of the solicitation. FEDERAL TRADE COMMISSION Rules and Regulations Under the Textile Fiber Products Iden
11、tification Act (Copies may be obtained from the Federal Trade Commission, Pennsylvania Avenue at Sixth Street, N.W., Washington, DC 20580.) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-W-4088K 83 777770b 037q773 3 MIL-W-4088K (Copies of draw
12、ings-, publications, and other Government documents required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity.) 2.2 Other publications. The following documents form a part of this speci- ficat
13、ion to the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted shall be those listed in the issue of the DODISS specified in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS shall be the issues of the no
14、ngovernment documents which are current on the date of the solicitation. American Association of Textile Chemists and Colorists (AATCC) Chromatic Transference Scale (Application for copies should be addressed to the American Association of Textile Chemists and Colorists, P.O. Box 12215, Research Tri
15、angle Park, NC 27709.) COLOR ASSOCIATION OF THE UNITED STATES Standard Color Card of America (Color cards may be available from the Color Association of the United States, Inc. , 343 Lexington Avenue, New York, NY 1001 6. If color cards are not avail- able from the Color Association, individual colo
16、r samples may be obtained from the contracting activity or as directed by the contracting activity.) (Nongovernment standards and other publications are normally available from the organizations which prepare or which distribute the documents. These documents also may be available in or through libr
17、aries or other informational services .) 2.3 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein, the text of this specification shall take precedence. Nothing in this specification , however, shall supersede applicable laws and regu
18、lations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Standard sample. The dyed webbing shall match the standard sample for shade and shall be equal to or better than the standard sample with respect to all characteristics for which the standard sample is referenced (see 6.3) .
19、3.2 First article. When specified in the contract or purchase order , a sample shall be subjected to first article inspection (see 4.3 , 6.2, and 6.5) - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-W-4O88K 83 W 7777706 0374774 5 MIL-W-4088K 3.
20、3 Material. 3.3.1 Nylon yarn. The nylon yarn used in the manufacture of the webbing shall be bright, high tenacity, light resistant and heat resistant. Nylon 6,6 shall be used for classes 1 and 1A wbbing and nylon 6 or 6,6 shall be used for class 2 webbing. The yarn shall not be bleached. Testing sh
21、all be as specified in 4.4.1 .l. 3.3.1.1 Denier and filament. The yarn used in the manufacturing of the webbing shall be of the denier and filament specified in tables II or III, before dyeing, except for the identification yarns (see 3.5). 3.3.1.2 Twist. The warp, binder and filling yarns shall hav
22、e a minimum of 2-1/2 turns per inch in the final twist whether single or plied, except types XXII and XXVII which shall have a minimum of 1-1/2 turns per inch. The number of single yarns specified in tables II and III shall be twisted together in one operation, 3.4 Color. Unless otherwise specified
23、(see 6.21, the webbing shall be furnished in the following colors: a. Natural White b. Natural White (special purpose items) c. Olive Drab 7 d. Camouflage Green 483 e. Air Force Sage Green 1531 f. Air Force Yellow 1365 3.4.1 Dyeing. When dyed webbing is required, the webbing shall be yarn or piece d
24、yed. 3.4.2 Matching. The color of the dyed and finished webbing shall match the standard sample when viewed under filtered tungsten lamps which approximate artificial daylight having a correlated color temperature of 7500 $- 200K, with illumination of 100 2 20 foot candles, and shall be a good match
25、 to the standard sample under incandescent lamplight at 2300 $- 200K. 3.4.3 Colorfastness. The finished webbing shall show fastness to light and laundering equal to or better than the standard sample or equal to or better than a rating of good“ for fastness to light and a rating of “fair“ for fastne
26、ss to laundering. The finished webbing shall show fastness to crocking equal to or better than the standard sample or shall have an AATCC Chromatic Transference Scale rating of not lower than 3.5. The webbing shall not be bleached. Testing shall be as specified in 4.4.3. 4 Provided by IHSNot for Res
27、aleNo reproduction or networking permitted without license from IHS-,-,-MIL-W-4088K 83 m 777770b 0374775 7 MIL-W-4088K 3.4.4 Spectral reflectance for Camouflage Green 483. Finished Camouflage Green 483 webbing greater than 1 1/4 inches in width. conforming to types VIII, VIIIa, VIIIb, VIIIc , XII an
28、d XII1 shall meet the spectral reflectance factors (in percent) for the visible/near infrared wavelength range 600 to 860 nanometers (nm) as specified below when tested as specified in 4.4.3. SDectral Reflectance Reauirements for Camouflaae Green 481 620 640 660 680 7 O0 720 3 10 760 3 10 78 0 3 11
29、8 O0 3 13 820 4 28 840 5 40 860 Wavelength (nm) Reflectance ($1 Wavelength (nm) Reflectance ($1 Min Max Min Max 600 - 3 10 740 7 52 11 60 17 64 24 67 32 70 37 71 40 73 - - 3.5 Identification yarns. Coiored warp ends shall be woven into the webbing, as specified herein, to permanently identify the we
30、bbing by type and manufacture, and when shuttleless construction and/or nylon 6 is utilized, except that natural white (special purpose items) webbing shall have no colored warp ends (see 6.2) . When the webbing is piece dyed, polyester yarn of approximate denier to the nylon body yarns shall be use
31、d for all required colored warp ends except that when black is specified, the identification yarn shall be 200 or 210 or 400/2 denier nylon 6, or 6,6, color-sealed black or 70, 90, or 150 denier polyester, color-sealed black (see table I). 3.5.1 Colorfastness of identifiation yarns. The colorfastnes
32、s rating of the type identification and manufacturers marker yarns shall be ogoodll to light and Irfairf1 to laundering when tested as specified in 4.4.3. 3.5.2 Type identification. The identification of type shall be as speci- fied in table I. The color of the identification yarns shall match the c
33、able numbers of the Color Association of the United States, Inc. 3.5.2.1 Other types. When type identification is required on other types, the identifying yarns shall be as specified in the procurement documents (see 6.2). 5 Provided by IHSNot for ResaleNo reproduction or networking permitted withou
34、t license from IHS-,-,-MIL-W-4088K 83 W 9997906 037497b 9 “ MIL-W-4088K TABLE I. Identification of type Type C o1 or Cable No. Yarns and location VI VI1 1 / VIII- XI I XII1 1 / XI x - XXII xxv I xxv II Red 7008 1 Yellow 70068 Black Black Green 70063 Black Red 700 81 Yellow 70068 B lack 2 at center o
35、f warp 2 at each selvage 2 at center of warp 1 at each selvage 2 at each selvage 2 at center of warp 2 at each selvage and 2 at center of warp 1 at each selvage 2 at center - 1/ These being double plain weaves the identification yarns shall weave so that one end shall show on the face and one on the
36、 back at each selvage. 3.5.3 Manufacturers identification. Each manufacturer of types VII, IX, X and XII1 shall incorporate, as part of the binder warp, 2 ends dyed to match the shade assigned to that manufacturer in accordance with MIL-STD-1480 (see 6.2 and 6.4). - 3.5.4 Shuttleless loom identifica
37、tion. When shuttleless loom construction * is utilized for classes 1A and 2, the catch-cord shall be 70 or 210 or 400 denier nylon, color-sealed black. Alternatively, the catch cord shall be 70, 90 or 150 denier polyester color-sealed black. 3.5.5 Nylon 6 identification. When nylon 6 is utilized for
38、 class 2, one edge of the webbing shall contain a red marker yarn, cable No,. 70081. 3.6 Physical requirements. The construction and physical requirements of the finished webbing shall be as specified in tables II and III when tested as specified in 4.4.3. 3.6.1 Breaking strength. The original break
39、ing strength of any specimen shall be no lower than the minimum specified in tables II and III. 3.6.1.1 Breaking strength after abrasion (types XXII and XXVII. The types XXII and XXVII webbing shall retain not less than 90 percent of the applicable minimum breaking strength values specified in table
40、 II when tested as specified in 4.4.3 (see 6.6). 3.6.2 Curvature. The finished webbing shall show no more lateral curvature than 1 /4 inch within a yard when tested as specified in 4.4.3. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-c n .o% a m-
41、 B a, a E+ h sh 22 O O0 N=r =r) 7 I 7 a- M I (U m O O Ln Co Y O O =r 9 Ln I (U O m (U c +I U3 m c H Bk z2 O O0 =rCo (U* Y I c =r m I Co z O a O (U r? O m Ln 9 Ln I Cu O Cu c +I =r M H m MIL-W-4088K Bh O Co= a- O0 =rCo (U3 c I =r M I =r c3 O U3 O (U O O a- O Ln I (U O (U c 7 +I c H H F= Co3 O a- O0 =
42、Co Cu* I =r rn I Co D c O co O N Ln O a- O 9 I Ln O (U . (U m c +I =r I c Y H H H 7 O zz O0 Cu=r =rCo 7 I Y =r M 1 O =r O O O W c O Y c a- O 9 I Ln O Cu Co c +I M H E- E B =r O Y O =t a3 (v I (U I Co O (U O O m o W O N O cc O I =r O 9 (U c M +I m m (U I (U I al O c O cc O I =r O 9 W c F +I (U D H .H
43、 HH E-E- h s (U I N I Ln O c Cu O PL O I =r O 9 LD 7 +I c =r c I (U H o H H k- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-n a L c, c: O U U -i rl !i( o H H MIL-W-4088K .-I o) v) 8: F: o .rl F F9 s O =r c 3 O a3 Cu Cu M a3 Cu 7 M c- ln Cu o O O m
44、 n O 9 =t O 2 ln I D O c Cu M +I M x H E F9 s O =r 7 =r O a3 Cu v- M (U Cu 7 M r- ln Cu O ln O m O P- M O 3 I Ln O 7 7 +I M Cu mm Cu Cu lm 7 x F w8- a33 O0 303 Cu* F I F 3 M I U3 U3 Cu O O U, 7 a3 Ln O =r O 9 9 I ln Cu +I Cu CW M- N I- F H H X E m z= O 3 7 3 O co Cu 7 Cu 3 Cu f M Co Cu c O O O r- O
45、m Cu O Cu O I Co c 9 +I N mm ?Cu Cu IM c H H H x F 5. 3 O F 3 =r O c f-NN CucuCu . i ; . I M .-. I a3 O Cu O O O O n 7 z 3 O M I O O 7 c X H x e Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-W-4088K 83 m 79777Ob 0374379 4 I MIL-W-4088K aal C or
46、 single float or skip greater than 1 inch Three or more, less than 1 /2 inch in combined warp and filling directions; or single float or skip greater than 1/2 inch but not exceeding 1 inch, if in warp, or more than 1/4 inch of width but not exceeding 1 inch, if in filling Clearly visible opening bet
47、ween adjoining picks, or warpwise tension area over part of the width resulting in visible light and heavy places - 2/ A clearly visible loop of filling pulled in at edges - 2/ More than 3 in any linear inches More than 1 knot in any 9 linear One knot e very 2 yards with inches untrimmed ends extend
48、ing from surface of webbing Two or more across the full width Single across the full width X X X X X X X Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_“ “ MIL-W-YOBBK 83 W 7797706 0375030 B W - MIL-W-4088K TABLE VI. Webbing visual defects (contd)
49、e Classification Exam i ne Defect Major Minor Slack end Two or more in the same length, jerked in between picks, or forming clearly visible loops on the surface or forming clearly visible loops on the surf ace Single jerked in between picks Slub, or slug, More than twice the thickness gout of the yarn (or ply, if plied) Smash Any smash .
