1、MIL-W-50987 13 977990b 0463987 4 Y- MIL- W- 5 O 9 87 (MU ) . 14 June i972 Superseding PA-PD-2581 (Rev. 1) 23 August i965 SPECIFICATION WARHEAD, 2.75 IIJCII ROCKET, HE, M151 WITH FUZE OR WITHOUT FUZE, LOADING, ASSEIIULING AIJD PACKING 1. SCOPE 1.1 This specification covers the quality assurance provi
2、- sions and special requirements not covered by the drawings, for one type of high explosive warhead designated as Warhead, 2.75 Inch Rocket, HE, 14151. 2. APPLICABLE DOCUMEIITS 2.1 The following documents of the issue in effect on date of invitation for bids or request for proposals, form a part of
3、 this specification to the extent specified herein. SPECIFICATIONS FIILITARY MIL-A-2550 - Ammunition and Special Weapons, General Specification For. STANDARDS MILITARY MIL-STD-105 - Sampling Procedures and Tables for NIL-STD-109 - Quality Assurance Terras nandatory (des lgnated “MU“ ) and non-mandat
4、ory (indicated by drawing or Federal Stock Yunber). When an inspection equipment list references mandatory Army designs, the contractor shall comply with, and use these designs accordingly. The con- tractor may, however, in connection with non-nandatory designs, and with the approval of the Governme
5、nt, design alternate inspec- tion equipnent or use comparable commercial equipment to facilitate his operations. Such contractor prepared esigns or commercial equipment selections nust be approved by the Government prior to fabrication or procuring of the equipment. Designs shall be sub- mitted for
6、approval as Specified in 6.3.5. 6.3.4 Contractor Designs. - Contractor designs are designs of inspection equipment for which the Government has assigned de- sign responsibility to the contractor. Contractor designs shall be supported by detailed drawings which depict all information necessary to com
7、pletely fabricate, calibrate and operate an item of inspection equipment. This requires that the necessary views, dimensions, materials, finish, notes, operating and calibration in- structions be propcrly depicted in accordance with approved prac- tices to the extent that further calculation or clar
8、ification Mill not be required. IJnless otherwise specified, contractor designs may be developed on the format the contractor normally employs in his equipment design procedure provided such format reflects the detail and information specified above, subject to the following controls: All submitted
9、contractor desiEns shall conform to MIL-D-1000, Category E, Form 2 Legibility and reproducibility shall permit conventional making of clearly understandable, high contrast reproductions, Contractors shall submit one copy of final designs as a rolled set. Designs shall be submitted for ap- pravai as
10、specified in 63.5. 11 Licensed by Information Handling ServicesMIL-W-50787 13 999790b 0463998 9 MI L-W- 5 O 9 8 7 ( MU ) c - 6.3.5 Submission of Designs, - Unless otherwise specified on the EL, all designs of equipment for inspection of defects classi- fied as critical and major shall be submitted f
11、or approval to the Commanding Officer, Picatinny Arsenal, ATTIJ: SMUPA-QA-A-R. All other designs of inspection equipment shall be approved by the inspection element of the agency administering the contract; sub- mission shall be as directed by the Contracting Officer. Partial submission of inspectio
12、n equipment designs is permissible and en- couraged. However, the Arsenal completion date for design review will be based on the date of the final submission of designs, tinny Arsenal design review will be accomplished normally within one month after receipt. the location for the evaluation of the f
13、irst article sample shall be obtained from the Contracting Officer. Upon receipt of such request, the Contracting Officer shall advise Picatinny Arsenal and instructions will be issued accordingly. be forwarded to: Commanding Officer, Picatinny Arsenal, ATTN: Pica- 6.4 Submission of First Article Sa
14、mples. - Instruction as to All inquiries should SMUPA-QA-I . G .5 The warhead-fuze combination is ballistically tested in accordance with specification MIL-F-50253(MU), Fuzes, Rocket, M423 and PI427 Loading, Assembling and Packing. data are used for any purpose other than in connection with a defini
15、tely related Government procurement operation, the United States Government thereby incurs no responsibility nor any obliga- tion whatsoever; and the fact that the Government may have formu- lated, furnished, or in any way supplied the said drawings, speci- fications, or other data is not to be rega
16、rded by implication or otherwise as in any manner licensing the holder or any other person or corporation or conveying any rights or permission to manufacture, use, or sell any patented invention that may in any way be related thereto. NOTICE: When Government drawings, specifications, or other Custodian: Army - MU Project No. : 1340 12 * U. b GOVERNMENT PRINTING OFFICE 1972-716535/525 Preparing Activity: Army - MU Licensed by Information Handling Services
