1、Designation: C390 08 (Reapproved 2013)Standard Practice forSampling and Acceptance of Thermal Insulation Lots1This standard is issued under the fixed designation C390; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of las
2、t revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope1.1 This practice covers criteria for e
3、stablishing the accept-ability of lots of shipments of preformed board, preformedblock and pipe, and batts and blanket thermal insulation basedon sampling and inspection.1.2 This practice is intended for use in conjunction withappropriate ASTM material specifications that classify anddescribe the sp
4、ecific physical requirements for the product interms of qualification requirements and inspection require-ments. Determination of nonconformity shall be based on thetolerances for individual sample test values prescribed in thematerial specification.1.3 This practice may require inspection substanti
5、ally dif-ferent from that performed in the normal course of production.If the purchaser requires sampling and acceptance inspection inaccordance with this practice, he shall so specify in the order orcontract.1.4 The values stated in inch-pound units are to be regardedas standard. The values given i
6、n parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.5 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appr
7、o-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2C168 Terminology Relating to Thermal InsulationE2234 Practice for Sampling a Stream of Product by Attri-butes Indexed by AQL3. Terminology3.1 Defini
8、tionsDefinitions pertaining to thermal insulat-ing materials are defined in Terminology C168.3.1.1 acceptable quality level (AQL)when a continuousseries of lots is considered, the quality level which for purposesof sampling inspection is the limit of a satisfactory processaverage. The listed AQL (AQ
9、L=10%) is the maximum percentdefective level accepted 95 % of the time by the sampling plan.3.1.2 acceptance numberthe maximum number of thenonconformities or nonconforming units in the sample that willpermit acceptance of the inspected lot or batch.3.1.3 inspectionthe process of measuring, examinin
10、g,testing, gaging, or otherwise comparing the unit with theapplicable requirements.3.1.4 inspection lota collection of units of product fromwhich a sample is drawn and inspected to determine confor-mance with the acceptability criteria.3.1.4.1 DiscussionAn inspection lot may differ from a lotdefined
11、 for other purposes.3.1.5 inspection, normalinspection that is used in accor-dance with an acceptance sampling scheme when a process isconsidered to be operating at, or slightly better than, itsacceptable quality level.3.1.6 inspection, tighteneda feature of a sampling schemeusing stricter acceptanc
12、e criteria than those used in normalinspection. Tightened inspection is used in some samplingschemes as a protective measure to increase the probability ofrejecting lots when experience shows the level of submittedquality has deteriorated significantly.3.1.6.1 DiscussionIt is expected that the highe
13、r rate ofrejections inherent with tightened inspection will lead thesupplier to improve the quality of the submitted product. Thecriteria for determining when quality has deteriorated signifi-cantly must be defined in objective terms for any givensampling scheme.3.1.7 lot (batch)a definite quantity
14、of some product manu-factured under conditions of production that are considereduniform.3.1.8 lot sizethe number of units in a lot or inspection lot.1This practice is under the jurisdiction of ASTM Committee C16 on ThermalInsulation and is the direct responsibility of Subcommittee C16.31 on Chemical
15、 andPhysical Properties.Current edition approved Nov. 1, 2013. Published March 2014. Originallyapproved in 1957. Last previous edition approved 2008 as C390 081. DOI:10.1520/C0390-08R13.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceas
16、tm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States13.1.9 nonconforming unita unit of product or servicecontainin
17、g at least one nonconformity.3.1.10 nonconformitya departure of a quality characteris-tic from its intended level or state that occurs with a severitysufficient to cause the product or service not to meet aspecification requirement.3.1.11 samplea group of units, portion of material, orobservations t
18、aken from the inspection lot that serves toprovide information that may be used as a basis for making adecision concerning the lot being inspected.3.1.12 sample sizethe number of units in a sample or thenumber of observations in a sample.3.1.13 unitan object on which a measurement or observa-tion ma
19、y be made.3.2 Definitions of Terms Specific to This Standard:3.2.1 lotan inspection lot as defined in 3.1.4.3.2.2 shipping packagethe smallest discrete package ofthermal insulation for purposes of shipping. Typically, ashipping package is one roll, bundle, bag, or carton of thermalinsulation.3.2.3 u
20、nita shipping package as described in 3.2.2.4. Significance and Use4.1 The sampling and inspection prescribed in this practiceafford the purchaser a practical level of quality assurance onincoming material. They are based on cost/risk relationshipsconsidered typical for preformed thermal insulations
21、 offeredfor general use. In all cases, the purchaser should review thispractice and determine its suitability in terms of his specificneeds.4.2 This procedure is intended primarily for the inspectionof a continuing stream of lots, and there is not a highprobability of rejecting occasional off lots.
22、Consumer protec-tion is based on economic pressure on the producer, throughgreater risk of lot rejection, to maintain the process average at90 % conformance or better. Operating characteristic curvesfor the sampling plans employed can be found in PracticeE2234, Table X-C through Table X-F.4.3 It is
23、not the intent of this procedure to estimate lotquality, control the quality of production, relieve the supplier ofresponsibility for the quality of material offered, or determinethe disposition of material found to be defective after receipt bythe purchaser.5. Classification of Requirements5.1 ASTM
24、 material specifications shall classify physicalrequirements in two categories:5.1.1 Qualification RequirementsThose requirementswhich establish the general suitability of the product but are notjudged necessary, or practical, for routine inspection. Theserequirements usually relate to the inherent
25、properties of thematerial, involve high inspection costs, require long-term tests,or are controlled indirectly by other requirements.5.1.2 Inspection RequirementsThose requirements whichcan and should be monitored on a routine basis. Theserequirements are characterized by a high benefit/cost ratio.T
26、hey may include visual and dimensional requirements, re-quirements for properties with potentially high variability, orrequirements providing indirect control of performance char-acteristics.6. Acceptance for Qualification Requirements6.1 The suppliers certificate of compliance or a thirdpartys cert
27、ificate of compliance shall be sufficient basis foracceptance of the lot for qualification requirements.6.1.1 The certificate shall state that compliance to thequalification requirements has been verified by actual inspec-tion of material manufactured within the past three years usingthe same basic
28、ingredients and manufacturing process as thematerial offered.6.1.2 The supplier shall furnish an inspection report uponrequest.7. Acceptance for Inspection Requirements7.1 The acceptance of a lot for inspection requirements shallbe based on the sampling plans and acceptance criteriaprescribed in Tab
29、le 1 (preformed board, and preformed blockand pipe) and Table 2 (batts and blanket). Single Inspectionand AQL = 10 % shall be used.7.2 Sampling and inspection shall be carried out as de-scribed in Section 8. Test sample shall be randomly selectedfrom the lot.7.3 For preformed board, and preformed bl
30、ock and pipe lotsof 150 units or less, or batts and blanket lots of 16 146ft2(1500 m2) or less, not subject to tightened inspection, thesuppliers certificate of compliance or a third partys certificateof compliance shall be sufficient basis for acceptance of the lotfor inspection requirements.TABLE
31、1 Sampling Plan and Acceptance Criteria for Inspection RequirementsA(Preformed Board, and Preformed Block and Pipe)Lot Size (Shipping Units)Normal Inspection Tightened InspectionSample Size(Shipping Packages)Acceptance Number,Maximum Number ofNonconforming UnitsSample Size(Shipping Packages)Acceptan
32、ceNumber,Maximum NumberofNonconformingUnits150 or less see 7.3 see 7.3 51151 to 1200 5 1 8 11201 to 35 000 8 2 8 135 000 and over 13 3 13 2AThe plan for normal inspection of lot sizes of 151 units and over, and the entire plan for tightened inspection are taken from Practice E2234, using Special Ins
33、pectionLevel S-2, AQL = 10 %.C390 08 (2013)27.3.1 The certificate shall state that compliance to inspec-tion requirements has been verified by actual inspection ofmaterial of the same type, class, form, size, and thicknessmanufactured within the same production period as the mate-rial offered.7.3.2
34、The supplier shall furnish pertinent inspection recordsupon request.8. Procedure for Sampling and Inspection8.1 Establish the grouping of product to be considered thelot and determine the lot size:8.1.1 Unless otherwise specified in the materialspecification, order, or contract, the lot shall consis
35、t of allthermal insulation of one type, class, form, size, and thicknessproduced under the same conditions and procured at the sametime.8.1.2 The lot size shall be equal to the number of shippingpackages in the lot.8.2 Determine the required sample size from Table 1,expressed in terms of shipping un
36、its:8.2.1 Use normal inspection at the start of inspection and forany single lot.8.2.2 Shift from normal to tightened inspection when two offive consecutive lots have been rejected.8.2.3 Shift from tightened to normal inspection after fiveconsecutive lots have been accepted.8.2.4 In the event that t
37、en consecutive lots remain ontightened inspection, discontinue inspection under this practicepending action to improve the quality of submitted product.8.3 Select the sample from the lot:8.3.1 The sample shall consist of the number of shippingpackages determined as the sample size in 8.2.8.3.2 Selec
38、t individual shipping packages from the entire lotat random and without regard to expected quality. Whenappropriate, select units from different sublots identified bysome rational criterion such as shipment or production group-ings.8.4 Perform the inspection called for in the ASTM materialspecificat
39、ion:8.4.1 From each shipping package in the sample, drawsufficient insulation material to perform the complete inspec-tion. This may require a full shipping package or a portionthereof, as one or more pieces cut from a roll or one or moreboards or sections from a carton. Select the material at rando
40、mand without regard to quality.8.4.2 Inspect the insulation material drawn from each ship-ping package in the sample. Perform the number of determi-nations prescribed in the product specification or specified testmethods.8.5 Establish the number of nonconforming units in thesample:8.5.1 Compare the
41、inspection results on the material drawnfrom each shipping unit to the requirements of the materialspecification.8.5.2 Classify the shipping unit as a nonconforming unit ifthe inspection results show one or more nonconformities to thematerial specification.8.6 Determine the acceptability of the lot:
42、8.6.1 If the number of nonconforming units is equal to orless than the appropriate acceptance number in Table 1, acceptthe lot.8.6.2 If the number of nonconforming units is greater thanthe acceptance number, reject the lot.9. Keywords9.1 batts; blanket; block; board; pipe; preformed; samplingand acc
43、eptance; thermal insulationTABLE 2 Sampling Plan and Acceptance Criteria for Inspection RequirementsA(Batts and Blankets)Lot Size (m2)BNormal Inspection Tightened InspectionSample Size(Shipping Packages)Acceptance Number,Maximum Number ofNonconforming UnitsSample Size(Shipping Packages)Acceptance Nu
44、mber,Maximum Number ofNonconforming Units1500 or less see 7.3 see 7.3 511501 to 2500 5 1 8 12501 to 5000 8 2 8 15001 to 9000 13 3 13 29001 to 15 000 20 5 20 315 001 to 28 000 32 7 32 528 001 and over 50 10 50 8AThe plan for normal inspection of lot sizes of 1500 m2and over, and the entire plan for t
45、ightened inspection are taken from Practice E2234, using Normal Inspection LevelII, AQL = 10 % and sample size based on 1080 ft2(100 m2) per unit.BLot sizes for ft2are 16 146 or less, 16 417 to 26 911, 26 912 to 53 821, 53 822 to 96 878, 96 879 to 161 460, 161 461 to 301 399, and 301 400 and over.C3
46、90 08 (2013)3ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of suc
47、h rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for addit
48、ional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the
49、 ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).C390 08 (2013
