1、Designation: F467 081Standard Specification forNonferrous Nuts for General Use1This standard is issued under the fixed designation F467; the number immediately following the designation indicates the year of originaladoption or, in the case of revision, the year of last revision. A number in parenth
2、eses indicates the year of last reapproval. A superscriptepsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1NOTE7.1 was editorially corrected in October 2009.1. Scope*1.1 This specification
3、covers the requirements for commer-cial wrought nonferrous nuts 0.250 to 1.500 in. inclusive indiameter in a number of alloys in common use and intended forgeneral service applications.1.2 Applicable bolts, cap screws, and studs for use with nutscovered by this specification are covered by Specifica
4、tionF468.1.3 This specification is the inch-pound companion toSpecification F467M; therefore, no SI equivalents are pre-sented in the specification.2. Referenced Documents2.1 ASTM Standards:2B154 Test Method for Mercurous Nitrate Test for CopperAlloysB574 Specification for Low-Carbon Nickel-Chromium
5、-Molybdenum, Low-Carbon Nickel-Molybdenum-Chromium-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten Alloy RodD3951 Practice for Commercial PackagingE18 Test Methods for Rockwell Hardness of Metallic Ma-terialsE29 Practice for Using Significan
6、t Digits in Test Data toDetermine Conformance with SpecificationsE34 Test Methods for Chemical Analysis of Aluminum andAluminum-Base AlloysE38 Methods for Chemical Analysis of Nickel-Chromiumand Nickel-Chromium-Iron Alloys3E53 Test Method for Determination of Copper in UnalloyedCopper by GravimetryE
7、54 Test Methods for ChemicalAnalysis of Special Brassesand Bronzes3E55 Practice for Sampling Wrought Nonferrous Metals andAlloys for Determination of Chemical CompositionE62 Test Methods for Chemical Analysis of Copper andCopper Alloys (Photometric Methods)E75 Test Methods for Chemical Analysis of C
8、opper-Nickeland Copper-Nickel-Zinc AlloysE76 Test Methods for Chemical Analysis of Nickel-CopperAlloys3E92 Test Method for Vickers Hardness of Metallic Materi-alsE101 Test Method for Spectrographic Analysis of Alumi-num and Aluminum Alloys by the Point-To-Plane Tech-nique3E120 Test Methods for Chemi
9、cal Analysis of Titanium andTitanium Alloys3E165 Practice for Liquid Penetrant Examination for GeneralIndustryE227 Test Method for Optical Emission SpectrometricAnalysis of Aluminum and Aluminum Alloys by thePoint-to-Plane Technique3E354 Test Methods for Chemical Analysis of High-Temperature, Electr
10、ical, Magnetic, and Other Similar Iron,Nickel, and Cobalt AlloysE478 Test Methods for ChemicalAnalysis of CopperAlloysE1409 Test Method for Determination of Oxygen andNitrogen in Titanium and Titanium Alloys by the Inert GasFusion TechniqueF468 Specification for Nonferrous Bolts, Hex Cap Screws,and
11、Studs for General UseF606 Test Methods for Determining the Mechanical Prop-erties of Externally and Internally Threaded Fasteners,Washers, Direct Tension Indicators, and RivetsF1470 Practice for Fastener Sampling for Specified Me-chanical Properties and Performance Inspection2.2 ASME Standards:41Thi
12、s specification is under the jurisdiction of ASTM Committee F16 onFasteners and is the direct responsibility of Subcommittee F16.04 on NonferrousFasteners.Current edition approved May 1, 2008. Published June 2008. Originallyapproved in 1976. Last previous edition approved in 2006 as F467 06a1. DOI:1
13、0.1520/F0467-08E01.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Withdrawn.4Available from Global Engineer
14、ing Documents, 15 Inverness Way, EastEnglewood, CO 80112-5704, http:/.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.B 1.1 Unified Inch Screw Threads (UN and UNR Thre
15、adForm)B 18.2.2 Square and Hex Nuts3. Ordering Information3.1 Orders for nuts under this specification shall include thefollowing information:3.1.1 Quantity (number of pieces of each item and size);3.1.2 Name of item;3.1.3 Size (diameter and threads per inch);3.1.4 Alloy number (Table 1);3.1.5 Stres
16、s relieving, if required (4.2.3);3.1.6 “Shipment lot” testing, as required (Section 9);3.1.7 Source inspection, if required (Section 14);3.1.8 Certificate of compliance or test report, if required(Section 16);3.1.9 Additional requirements, if any, to be specified onthe purchase order (4.2.1, 7.2, 8.
17、2, 12.1, and 13.1),3.1.10 Supplementary requirements, if any; and3.1.11 ASTM designation (including year or publisheddate).NOTE 1A typical ordering description is as follows: 10 000 pieces,Hex Nut, 0.2509 -20, Alloy 270, Furnish Certificate of Compliance,Supplementary Requirement S 1, ASTM Specifica
18、tion F 467-XX4. Materials and Manufacture4.1 Materials:4.1.1 The nuts shall be manufactured from material havinga chemical composition conforming to the requirements inTable 2 and capable of developing the required mechanicalproperties for the specified alloy in the finished fastener. SeeSpecificati
19、on B574 for nickel alloys.4.1.2 The starting condition of the raw material shall be atthe discretion of the fastener manufacturer but shall be suchthat the finished products conform to all the specified require-ments.4.2 Manufacture:4.2.1 FormingUnless otherwise specified, the nuts shallbe hot press
20、ed, cold formed, or machined from suitablematerial at the option of the manufacturer.4.2.2 ConditionExcept as provided in 4.2.3, the nuts shallbe furnished in the condition specified below:Alloy ConditionCopper (all alloys) As formed or stress relieved at manufacturersoptionNickel alloys 400 and 405
21、 As formed or stress relieved at manufacturersoptionNickel alloy 500 Solution annealed and agedAluminum alloys:2024-T4 Solution treated and naturally aged6061-T6 Solution treated and artificially aged6262-T9 Solution treated, artificially aged, and coldworkedTitanium As formed625 Annealed4.2.3 Stres
22、s RelievingWhen required, stress relievingshall be specified by the purchaser for all copper alloys andnickel alloys 400 and 405.5. Chemical Composition5.1 Chemical CompositionThe nuts shall conform to thechemical composition specified in Table 1 for the specifiedalloy.5.2 Manufacturers Analysis:5.2
23、.1 Except as provided in 5.2.2, when test reports arerequired on the inquiry or purchase order (3.1.8), the manu-facturer shall make individual analyses of randomly selectedfinished nuts from the product to be shipped and report theresults to the purchaser. Alternatively, if heat and lot identitiesh
24、ave been maintained, the analysis of the raw material fromwhich the nuts have been manufactured may be reportedinstead of product analysis.5.2.2 For aluminum nuts, instead of 5.2.1, the manufacturermay furnish a certificate of conformance certifying compliancewith the chemical composition specified
25、in Table 1.5.3 Product Analysis:5.3.1 Product analyses may be made by the purchaser fromfinished products representing each lot. The chemical compo-sition thus determined shall conform to the requirements inTable 1.5.3.2 In the event of disagreement, a referee chemicalanalysis of samples from each l
26、ot shall be made in accordancewith 12.1 and 13.1.6. Mechanical Properties6.1 The nuts shall be tested in accordance with the mechani-cal testing requirements for the applicable type and shall meetthe mechanical requirements in Table 2 for the specified alloy.6.2 Where both proof load and hardness te
27、sts are performed,the proof load test results shall take precedence for acceptancepurposes.7. Dimensions7.1 NutsUnless otherwise specified, the dimensions ofnuts shall be in accordance with the requirements of ASMEB 18.2.2.7.2 ThreadsUnless otherwise specified, the nuts shallhave Class 2B threads in
28、 accordance with ASME B 1.1.8. Workmanship, Finish, and Appearance8.1 WorkmanshipNuts shall have a workmanlike finishfree of injurious burrs, seams, laps, irregular surfaces, andother imperfections affecting serviceability.8.2 FinishUnless otherwise specified, the nuts shall befurnished without any
29、additive chemical or metallic finish.9. Sampling9.1 A lot, for the purposes of selecting test specimens, shallconsist of not more than 100 000 pieces offered for inspectionat one time having the following common characteristics:9.1.1 One type of item,9.1.2 Same alloy and temper, and9.1.3 One nominal
30、 diameter and thread series.10. Number of Tests and Retests10.1 Normal TestingThe requirements of this specifica-tion shall be met in continuous mass production for stock (seeF467 0812Table 3). The manufacturer shall make sample inspections asspecified below to ensure that the product conforms to th
31、especified requirements. When tests of individual shipments arerequired, Supplementary Requirement S 2 shall be specified.Acceptance CriteriaNumber of Pieces inLotNo. ofTestsAccept-ance No.RejectionNo.50 and under 2 0 151 to 500 3 0 1501 to 35 000 5 0 135 001 to 100 000 8 0 110.2 Retests:10.2.1 When
32、 tested in accordance with the required sam-pling plan, a lot shall be subject to rejection if any of the testspecimens fails to meet the applicable test requirements.10.2.2 If the failure of a test specimen is due to improperpreparation of the specimen or to incorrect testing technique,the specimen
33、 shall be discarded and another specimen substi-tuted.11. Significance of Numerical Limits11.1 For purposes of determining compliance with thespecified limits for requirements of the properties listed in thisspecification, an observed value or calculated value shall berounded in accordance with Prac
34、tice E29.12. Test Specimens12.1 Chemical TestsWhen required, samples for chemicalanalysis shall be taken in accordance with Practice E55 bydrilling, sawing, milling, turning, clipping, or such othermethods capable of producing representative samples.12.2 Mechanical Tests:12.2.1 Nuts shall be tested
35、in full section.12.2.2 The hardness shall be determined on the top orbottom face of the nut.13. Test Methods13.1 Chemical AnalysisWhen required, the chemicalcomposition shall be determined by any recognized commer-cial test method. In the event of disagreement, the followingtest methods shall be use
36、d for referee purposes.Alloy Test MethodCopper E53, E54, E62, E75, E478Aluminum E 34E34, E101,8aE227Nickel E 38E38, E76, E354Titanium E 120E120, E140913.2 Mechanical:13.2.1 The proof load or proof stress tests shall be deter-mined in accordance with the appropriate methods of TestMethods F606. Loads
37、 to be determined using Table 2 and Table4.13.2.2 The hardness shall be determined in accordance withTest Methods E18 and E92E18E92. For sizes14 (0.250) to716(0.4375) in. one reading shall be taken. For sizes12 (0.500) in.and larger the hardness shall be the average of four readingslocated 90 to one
38、 another.14. Inspection14.1 When specified on the inquiry or purchase order, theproduct shall be subject to inspection by the purchaser at theplace of manufacture prior to shipment. The inspector repre-senting the purchaser shall have controlled entry only to thoseparts of the manufacturers operatio
39、ns that concern the manu-facture of the ordered product and only when and where workon the contract of the purchaser is being performed. Themanufacturer shall afford the inspector all reasonable facilitiesto satisfy him that the product is being furnished in accordancewith this specification. All in
40、spections and tests shall beconducted so as not to interfere unnecessarily with the opera-tions of the manufacturer.15. Rejection and Rehearing15.1 Unless otherwise specified, any rejection based on testsspecified herein and made by the purchaser shall be reported tothe manufacturer as soon as pract
41、ical after receipt of theproduct by the purchaser.16. Certification and Test Reports16.1 Certificate of ComplianceWhen specified in thecontract or purchase order, the manufacturer shall furnishcertification that the product was manufactured and tested inaccordance with this specification and conform
42、s to all specifiedrequirements.16.2 Test ReportsWhen “Shipment Lot Testing” in accor-dance with Supplementary Requirement S2 is specified in thecontract or purchase order, the manufacturer shall furnish a testreport showing the results of the mechanical tests for each lotshipped.17. Product, Packagi
43、ng and Package Marking17.1 Individual NutsAll products shall be marked with asymbol identifying the manufacturer. In addition, they shall bemarked with the alloy/mechanical property marking specifiedin Table 1. The marking shall be raised or depressed at theoption of the manufacturer.17.2 Packaging:
44、17.2.1 Unless otherwise specified, packaging shall be inaccordance with Practice D3951.17.2.2 When special packaging requirements are requiredby the purchaser, they shall be defined at the time of inquiryand order.17.3 Package MarkingEach shipping unit shall includeor be plainly marked with the foll
45、owing:17.3.1 ASTM designation,17.3.2 Alloy number,17.3.3 Alloy/mechanical property marking,17.3.4 Size,17.3.5 Name and brand or trademark of the manufacturer,17.3.6 Number of pieces,17.3.7 Country of origin, and17.3.8 Purchase order number.18. Keywords18.1 general use; nonferrous; nutsF467 0813SUPPL
46、EMENTARY REQUIREMENTSOne or more of the following supplementary requirements shall be applied only when specified bythe purchaser in the inquiry, contract, or order. Supplementary requirements shall in no way negate anyrequirement of the specification itself.S1. Stress Corrosion Requirements, Copper
47、 AlloysS1.1 Copper alloy fasteners shall exhibit no evidence ofcracking after immersion for 30 min in an aqueous solution ofmercurous nitrate when tested in accordance with Test MethodB154.S1.1.1 WarningMercury is a definite health hazard andequipment for the detection and removal of mercury vaporpr
48、oduced in volatilization is recommended. The use of rubbergloves in testing is advisable.S2. Shipment Lot TestingS2.1 When Supplementary Requirement S2 is specified onthe order (3.1.6), the manufacturer shall make sample tests onthe individual lots for shipment to ensure that the productconforms to
49、the specified requirements.S2.2 The manufacturer shall make an analysis of a ran-domly selected finished nut from each lot of product to beshipped. Heat or lot control shall be maintained. The analysisof the starting material from which the nuts have beenmanufactured may be reported in place of the product analysis.S2.3 The manufacturer shall perform mechanical propertytests in accordance with this specification and Guide F1470 onthe individual lots for shipment.S2.4 The manufacturer shall furnish a test report for eachlot in the shipm
