1、BRITISH STANDARD BS 7442-1: 1991 ISO/TR 8517: 1988 Rubber or plastics covered rollers Part 1: Glossary of termsBS7442-1:1991 This British Standard, having been prepared under the directionof the Plastics and Rubber Standards Policy Committee, was published underthe authority of the Standards Board a
2、nd comes intoeffect on 28 June 1991 BSI 02-2000 The following BSI references relate to the work on this standard: Committee reference PRM/73 Draft for comment 85/37776 DC ISBN 0 580 19746 8 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the
3、 Plastics and Rubber Standards Policy Committee (PRM/-) to Technical Committee PRM/73, upon which the following bodies were represented: British Rubber Manufacturers Association British Structural Bearings Manufacturers Association Building Employers Confederation Department of the Environment (Buil
4、ding Research Establishment) Department of Transport Institute of Medical Laboratory Sciences Institution of Structural Engineers Malaysian Rubber Producers Research Association Ministry of Defence Royal Society of Chemistry Amendments issued since publication Amd. No. Date CommentsBS7442-1:1991 BSI
5、 02-2000 i Contents Page Committees responsible Inside front cover National foreword ii 1 Scope and field of application 2 2 References 2 3 General term 2 4 Construction terms 2 5 Terms concerning operating conditions 3 6 Terms concerning dimensions and geometry 4 7 Terms concerning the surface char
6、acteristics of plane rollers 6 8 Terms for grooved rollers 7 9 Balance 7 Figure Edge finish, end relief 8 Indexes English alphabetical index 9 French alphabetical index 11 Publication(s) referred to Inside back coverBS7442-1:1991 ii BSI 02-2000 National foreword This British Standard has been prepar
7、ed under the direction of the Plastics and Rubber Standards Policy Committee. It is identical with ISO/TR 8517:1988 “Rubber- or plastics-covered rollers Glossary”, published by the International Organization for Standardization (ISO). Cross-references The Technical Committee has reviewed the provisi
8、ons of ISO 6123-2, to which reference is made in the text, and has decided that they are acceptable for use in conjunction with this standard. NOTEThis ISO technical report is being dual-numbered as a British Standard because the Technical Committee envisage that the terms defined will remain unchan
9、ged for some time. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. International Standard
10、 Corresponding British Standard ISO 472:1979 BS 1755 Glossary of terms used in the plastics industry Part 1:1982 Polymer and plastics technology (Technically equivalent) ISO 1925:1990 BS 3851:1990 Glossary of terms used in the mechanical balancing of rotating machinery (Identical) ISO 4287-1:1984 BS
11、 6741 Glossary of surface roughness terms Part 1:1987 Surface and its parameters (Identical) Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, pages1 to12, an inside back cover and aback cover. This standard has been updated (see copyright date) and may hav
12、e had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BS7442-1:1991 BSI 02-2000 1BS7442-1:1991 2 BSI 02-2000BS7442-1:1991 BSI 02-2000 3BS7442-1:1991 4 BSI 02-2000BS7442-1:1991 BSI 02-2000 5BS7442-1:1991 6 BSI 02-2000BS7442-1:1991 BSI 02-2000 7BS7442-1
13、1991 8 BSI 02-2000BS7442-1:1991 BSI 02-2000 9BS7442-1:1991 10 BSI 02-2000BS7442-1:1991 BSI 02-2000 1112 blankBS 7442-1:1991 BSI 02-2000 Publication(s) referred to See national foreword.BS7442-1: 1991 ISO/TR8517: 1988 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the
14、 independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that
15、they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the
16、 identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and for
17、eign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information
18、on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Inf
19、ormation Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967
20、001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or tra
21、nsmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.
