1、BRITISH STANDARDBS EN 2349-305:2006Aerospace series Requirements and test procedures for relays and contactors Part 305: Bounce timeThe European Standard EN 2349-305:2006 has the status of a British StandardICS 49.060g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54
2、g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58Licensed Copy: Wang Bin, na, Mon Oct 15 02:16:18 GMT+00:00 2007, Uncontrolled Copy, (c) BSIBS EN 2349-305:2006This British Standard was published under the authority of the Standards
3、Policy and Strategy Committee on 31 July 2007 BSI 2007ISBN 978 0 580 50021 3National forewordThis British Standard was published by BSI. It is the UK implementation of EN 2349-305:2006.The UK participation in its preparation was entrusted by Technical Committee ACE/6, Aerospace avionic electrical an
4、d fibre optic technology, to Panel ACE/6/-/4, Aerospace Switching devices.A list of organizations represented on ACE/6/-/4 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct applic
5、ation.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments issued since publicationAmd. No. Date CommentsLicensed Copy: Wang Bin, na, Mon Oct 15 02:16:18 GMT+00:00 2007, Uncontrolled Copy, (c) BSIEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 2349-305October
6、 2006ICS 49.060English VersionAerospace series - Requirements and test procedures for relaysand contactors - Part 305: Bounce timeSrie arospatiale - Exigences et mthodes dessais desrelais et contacteurs - Partie 305 : Temps derebondissementLuft- und Raumfahrt - Anforderungen und Prfverfahren frRelai
7、s und Schaltschtze - Teil 305: PrellzeitThis European Standard was approved by CEN on 10 May 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-
8、date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the
9、responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ire
10、land, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36
11、 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 2349-305:2006: ELicensed Copy: Wang Bin, na, Mon Oct 15 02:16:18 GMT+00:00 2007, Uncontrolled Copy, (c) BSI2 Contents Page Foreword3 1 Scope 4 2 Normative referenc
12、es 4 3 Test procedures.4 4 Test criteria.4 EN 2349-305:2006Licensed Copy: Wang Bin, na, Mon Oct 15 02:16:18 GMT+00:00 2007, Uncontrolled Copy, (c) BSI3 Foreword This document (EN 2349-305:2006) has been prepared by the AeroSpace and Defence Industries Association of Europe - Standardization (ASD-STA
13、N). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the statu
14、s of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2007, and conflicting national standards shall be withdrawn at the latest by April 2007. Attention is drawn to the possibility that some of the elements of this document may be the subject
15、of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus
16、, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 2349-305:2006Licensed Copy: Wang Bin
17、, na, Mon Oct 15 02:16:18 GMT+00:00 2007, Uncontrolled Copy, (c) BSI4 1 Scope This standard specifies a method for testing the bounce time of relays and contactors. It shall be used together with EN 2349-100. 2 Normative references The following referenced documents are indispensable for the applica
18、tion of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2349-100, Aerospace series Requirements and test procedures for relays and contactors Part 100: General requiremen
19、ts 1)3 Test procedures 3.1 Bounce time shall be measured, both on the normally-open and normally-closed contacts, by applying the rated voltage on and off. 3.2 The bounce time includes both the initial bounce, when the contacts close or open for the first time, and all additional bounces, see Figure
20、s 2 and 3. 3.3 The contact load shall be between 5 mA and 100 mA. The open contact voltage shall be 6 V d.c. max. for relays or contactors with ratings of up to and including 25 A, and 28 V d.c. max. for relays or contactors with ratings above 25 A. 3.4 For qualification tests, five measurements sha
21、ll be taken and recorded. 3.5 Figure 1 shows a typical test circuit. 3.6 The test shall be performed in such a way that the records cover all occurrences of bounce. 4 Test criteria The relay or contactor shall not exceed the bounce times specified in the product standard. 1) In preparation at the da
22、te of publication of this standard. EN 2349-305:2006Licensed Copy: Wang Bin, na, Mon Oct 15 02:16:18 GMT+00:00 2007, Uncontrolled Copy, (c) BSI5 Figure 1 Test circuit for the determination of the operate, release and bounce times Figure 2 Switch closure at t = 0, Operate time characteristics Key R1,
23、 R2resistor 60 DUT device under test (relay) 1 trigger input self-synchronous 2 signal input oscilloscope (vertical 3 ground input deflection) U1control voltage U2test voltage 6 V d.c. S switch aNO contact bNC contact Key 1 dynamic contact resistance effect t1operate time t2transfer time t3contact b
24、reak bounce duration t4contact closing bounce duration (make bounces) EN 2349-305:2006Licensed Copy: Wang Bin, na, Mon Oct 15 02:16:18 GMT+00:00 2007, Uncontrolled Copy, (c) BSI6 Figure 3 Switch opening at t = 0, Release time characteristics Key 1 dynamic contact resistance effect t2transfer time t3
25、contact break bounce duration t5release time t6contact make bounce duration EN 2349-305:2006Licensed Copy: Wang Bin, na, Mon Oct 15 02:16:18 GMT+00:00 2007, Uncontrolled Copy, (c) BSIblankLicensed Copy: Wang Bin, na, Mon Oct 15 02:16:18 GMT+00:00 2007, Uncontrolled Copy, (c) BSIBS EN 2349-305:2006BS
26、I389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are upda
27、ted by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British
28、Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically rece
29、ive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bs
30、i-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standard
31、s through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing membe
32、rs of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding o
33、nline access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international
34、 standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does no
35、t preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.Licensed Copy: Wang Bin, na, Mon Oct 15 02:16:18 GMT+00:00 2007, Uncontrolled Copy, (c) BSI
