1、BRITISH STANDARD BS EN3840:2007 Aerospace series Paints and varnishes Technical specification The European Standard EN 3840:2007 has the status of a British Standard ICS 49.040 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Amd. No. Date Comments BS EN 3840:2007 National fore
2、word This British Standard is the UK implementation of EN 3840:2007. The UK participation in its preparation was entrusted by Technical Committee ACE/65, Non-metallic materials for aerospace purposes (excluding textiles), to Panel ACE/65/-/3, Paints. A list of organizations represented on this commi
3、ttee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was pu
4、blished under the authority of the Standards Policy and Strategy Committee on 31 August 2007 BSI 2007 ISBN 978 0 580 54529 0 Amendments issued since publication EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 3840 July 2007 ICS 49.040 English Version Aerospace series - Paints and varnishes - Te
5、chnical specification Srie arospatiale - Peintures et vernis - Spcification technique Luft- und Raumfahrt - Beschichtungsstoffe - Technische Lieferbedingungen This European Standard was approved by CEN on 13 April 2007. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
6、stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Stan
7、dard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national st
8、andards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United
9、Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION C OM I T EUR OP EN DE NOR M A L I S ATI ON EUR OP I S C HES KOM I TEE F R NOR M UNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref
10、. No. EN 3840:2007: E EN 3840:2007 2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Terms and definitions .7 4 Requirements .8 5 Quality assurance 9 6 Batch release testing.11 7 Packaging and labelling 12 Annex A (normative) Test method.13 Annex B (normative) Qualification requirements
11、 for colour and gloss 15 Annex C (informative) Certificate of conformity 2.1/Acceptance test certificate 3.1 B according to EN 10204 for paints and varnishes 16 EN 3840:2007 3 Foreword This document (EN 3840:2007) has been prepared by the Aerospace and Defence Industries Association of Europe - Stan
12、dardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shal
13、l be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2008, and conflicting national standards shall be withdrawn at the latest by January 2008. Attention is drawn to the possibility that some of the elements of this docu
14、ment may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard:
15、Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 38
16、40:2007 4 1 Scope This standard defines the technical requirements for the qualification, manufacture, inspection and the delivery of paints and varnishes for use in aerospace applications. It shall be applied in conjunction with the EN material specification. 2 Normative references The following re
17、ferenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 3847, Aerospace series Paints and varnishes Determination of s
18、edimentation rating. 1)EN 4158, Aerospace series Paints and varnishes Test method for measurement of electrical surface resistance of conductive layers. EN 4159, Aerospace series Paints and varnishes Determination of resistance to microbial growth. 1)EN 4160, Aerospace series Non-metallic materials
19、Paints and varnishes Test methods Determination of the effect of thermal exposure. 1)EN 4170, Aerospace series Paints and varnishes Test method for measurement of resistance to cold crack temperature cycle. 1)EN 4171, Aerospace series Paints and varnishes Test method for determination of phosphoric
20、acid index. 1)EN 4195, Aerospace series Paints and varnishes Test method for determination of chromate leaching. 1)EN 4508, Aerospace series Paints and varnishes Test method for anti slip coatings Determination of the sliding friction behaviour. EN 4592, Aerospace series Paints and varnishes Test me
21、thod for determination of infrared reflectance. EN 9100, Aerospace series Quality management systems Requirements (based on ISO 9001:2000) and Quality systems Model for quality assurance in design, development, production, installation and servicing (based on ISO 9001:1994). EN 10204, Metallic produ
22、cts Types of inspection documents. EN 23270, Paints and varnishes and their raw materials Temperatures and humidities for conditioning and testing (ISO 3270:1984). EN 29117, Paints and varnishes Determination of through-dry state and through-dry time Method of test (ISO 9117:1990). EN ISO 1513, Pain
23、ts and varnishes Examination and preparation of samples for testing (ISO 1513:1992). 1) Published as ASD Prestandard at the date of publication of this standard. EN 3840:2007 5 EN ISO 1517, Paints and varnishes Surface-drying test Ballotini method (ISO 1517:1973). EN ISO 1518, Paints and varnishes S
24、cratch test (ISO 1518:1992). EN ISO 1519, Paints and varnishes Bend test (cylindrical mandrel) (ISO 1519:2002). EN ISO 1520, Paints and varnishes Cupping test (ISO 1520:1999). EN ISO 1524, Paints, varnishes and printing inks Determination of fineness of grind (ISO 1524:2000). EN ISO 2114, Plastics (
25、polyester resins) and paints and varnishes (binders) Determination of partial acid value and total acid value (ISO 2114:2000). EN ISO 2409, Paints and varnishes Cross-cut test (ISO 2409:1992). EN ISO 2431, Paints and varnishes Determination of flow time by use of flow cups (ISO 2431:1993, including
26、Technical Corrigendum 1:1994). EN ISO 2808, Paints and varnishes Determination of film thickness (ISO 2808:1997). EN ISO 2810, Paints and varnishes Natural weathering of coatings Exposure and assessment (ISO 2810:2004). EN ISO 2811-1, Paints and varnishes Determination of density Part 1: Pyknometer
27、method (ISO 2811-1:1997). EN ISO 2811-2, Paints and varnishes Determination of density Part 2: Immersed body (plummet) method (ISO 2811-2:1997). EN ISO 2811-3, Paints and varnishes Determination of density Part 3: Oscillation method (ISO 2811-3:1997). EN ISO 2811-4, Paints and varnishes Determinatio
28、n of density Part 4: Pressure cup method (ISO 2811-4:1997). EN ISO 2812-1, Paints and varnishes Determination of resistance to liquids Part 1: General methods (ISO 2812-1:1993). EN ISO 2812-2, Paints and varnishes Determination of resistance to liquids Part 2: Water immersion method (ISO 2812-2:1993
29、). EN ISO 2813, Paints and varnishes Determination of specular gloss of non-metallic paint films at 20, 60 and 85 (ISO 2813:1994, including Technical Corrigendum 1:1997). EN ISO 3001, Plastics Epoxy compounds Determination of epoxy equivalent (ISO 3001:1999). EN ISO 3251, Paints, varnishes and plast
30、ics Determination of non-volatile matter content (ISO 3251:2003). EN ISO 3668, Paints and varnishes Visual comparison of the colour of paints (ISO 3668:1998). EN ISO 3675, Crude petroleum and liquid petroleum products Laboratory determination of density Hydrometer method (ISO 3675:1998). EN ISO 3678
31、, Paints and varnishes Print-free test (ISO 3678:1976). EN ISO 3679, Determination of flash point Rapid equilibrium closed cup method (ISO 3679:2004). EN ISO 3680, Determination of flash/no flash Rapid equilibrium closed cup method (ISO 3680:2004). EN 3840:2007 6 EN ISO 4617, Paints and varnishes Li
32、st of equivalent terms (ISO 4617:2000). EN ISO 4618, Paints and varnishes Terms and definitions (ISO/DIS 4618:2004). EN ISO 4623-1, Paints and varnishes Determination of resistance to filiform corrosion Part 1: Steel substrates (ISO 4623-1:2000). EN ISO 4623-2, Paints and varnishes Determination of
33、resistance to filiform corrosion Part 2: Aluminium substrates (ISO 4623-2:2003). EN ISO 4629, Binders for paints and varnishes Determination of hydroxyl value Titrimetric method (ISO 4629:1996). EN ISO 6270-1, Paints and varnishes Determination of resistance to humidity Part 1: Continuous condensati
34、on (ISO 6270-1:1998). EN ISO 6272-1, Paints and varnishes Rapid-deformation (impact resistance) tests Part 1: Falling-weight test, large-area indenter (ISO 6272-1:2002). EN ISO 7253, Paints and varnishes Determination of resistance to neutral salt spray (fog) (ISO 7253:1996). EN ISO 9001, Quality ma
35、nagement systems Requirements (ISO 9001:2000). EN ISO 9514, Paints and varnishes Determination of the pot life of multicomponent coating systems Preparation and conditioning of samples and guidelines for testing (ISO 9514:1992). EN ISO 9702, Plastics Amine epoxide hardeners Determination of primary,
36、 secondary and tertiary amine group nitrogen content (ISO 9702:1996). EN ISO 11341, Paints and varnishes Artificial weathering and exposure to artificial radiation Exposure to filtered xenon-arc radiation (ISO 11341:2004). EN ISO 11507, Paints and varnishes Exposure of coatings to artificial weather
37、ing Exposure to fluorescent UV and water (ISO 11507:1997). EN ISO 11890-1, Paints and varnishes Determination of volatile organic compound (VOC) content Part 1: Difference method (ISO 11890-1:2000). EN ISO 11890-2, Paints and varnishes Determination of volatile organic compound (VOC) content Part 2:
38、 Gas-chromatographic method (ISO 11890-2:2000). EN ISO 11909, Binders for paints and varnishes Polyisocyanate resins General methods of test (ISO 11909:1996). EN ISO 15528, Paints, varnishes and raw materials for paints and varnishes Sampling (ISO 15528:2000). ISO 760, Determination of water Karl Fi
39、scher method (General method). ISO 2718, Standard layout for a method of chemical analysis by gas chromatography. ISO 2884-1, Paints and varnishes Determination of viscosity using rotary viscometers Part 1: Cone-and- plate viscometer operated at a high rate of shear. ISO 3233, Paints and varnishes D
40、etermination of percentage volume of non-volatile matter by measuring the density of dried coating. ISO 5661, Petroleum products Hydrocarbon liquids Determination of refractive index. EN 3840:2007 7 ISO 6286, Molecular absorption spectrometry Vocabulary General Apparatus. ISO 6504-1, Paints and varn
41、ishes Determination of hiding power Part 1: Kubelka-Munk method for white and light-coloured paints. ISO 6504-3, Paints and varnishes Determination of hiding power Part 3: Determination of contrast ratio of light-coloured paints at a fixed spreading rate. ISO 7724-1, Paints and varnishes Colorimetry
42、 Part 1: Principles. ISO 7724-2, Paints and varnishes Colorimetry Part 2: Colour measurement. ISO 7724-3, Paints and varnishes Colorimetry Part 3: Calculation of colour differences. ISO 7784-2, Paints and varnishes Determination of resistance to abrasion Part 2: Rotating abrasive rubber wheel method
43、. ISO 14680-1, Paints and varnishes Determination of pigment content Part 1: Centrifuge method. ISO 14680-2, Paints and varnishes Determination of pigment content Part 2: Ashing method. ISO 14680-3, Paints and varnishes Determination of pigment content Part 3: Filtration method. ISO 15710, Paints an
44、d varnishes Corrosion testing by alternate immersion in and removal from a buffered sodium chloride solution. ISO 15716, Binders for paints and varnishes Determination of storage stability. TR 7000-9, Aerospace series Non-metallic materials Rules for the drafting and presentation of material standar
45、ds Part 9: Paints and varnishes. 2)ASTM D 2370, Standard test method for tensile properties of organic coatings. 3)DIN 6175-1, Tolerances for automotive paints Uni paints. 3 Terms and definitions For the purposes of this standard, the terms and definitions given in EN 9100, EN ISO 4617, EN ISO 4618
46、and EN ISO 9001 as well as the following terms and definitions apply. 3.1 product in this and associated documents, the word product refers to all forms of paints and varnishes 3.2 production batch a production batch is a quantity of one product of determined composition produced in a single or cont
47、inuous run to a defined manufacturing schedule 2) Published as ASD Technical Report at the date of publication of this standard. 3) Published by: ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA, 19428-2959 USA. EN 3840:2007 8 3.3 manufacturing schedule a manufacturing s
48、chedule is a document prepared by the manufacturer in accordance with EN ISO 9001 and/or EN 9100, which defines the actual manufacturing procedure and inspection verification stages to be followed in the production of a product/part to ensure that: the product/part is produced in a controlled and consistent manner; special properties and/or function in service are reproducible; the product/part fulfils the requirements of the technical specification and material specification. 4 Requirements 4.1 General requirements 4.1.1 Manufacturing schedule The product shall be manufactured
