1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 951:1999 The Europe
2、an Standard EN 951:1998 has the status of a British Standard ICS 91.060.50 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Door leaves Method for measurement of height, width, thickness and squarenessThis British Standard, having been prepared under the direction of the Sector
3、 Committee for Building and Civil Engineering, was published under the authority of the Standards Committee and comes into effect on 15 May 1999 BSI 05-1999 ISBN 0 580 32281 5 BS EN 951:1999 Amendments issued since publication Amd. No. Date Text affected National foreword This British Standard is th
4、e English language version of EN 951:1998. The UK participation in its preparation was entrusted to Technical Committee B/538, Doors, windows, shutters, hardware and curtain walling, which has the responsibility to: aid enquirers to understand the text; present to the responsible European committee
5、any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. This British Sta
6、ndard forms part of a package of standards on doors which will not become fully effective until all standards in the package have been published and any superseded standards have been withdrawn. The date of withdrawal for national standards will be agreed within CEN and will be notified. Cross-refer
7、ences The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catal
8、ogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comp
9、rises a front cover, an inside front cover, the EN title page, pages 2 to 4, an inside back cover and a back cover.CEN European Committee for Standardization Comite Europe en de Normalisation Europa isches Komitee fu r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1998 CEN All rig
10、hts of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 951:1998 E EUROPEAN STANDARD EN 951 NORME EUROPE ENNE EUROPA ISCHE NORM December 1998 ICS 91.060.50 Supersedes EN 25:1975 Descriptors: door leaves, dimension measurements, height, width, thickne
11、ss, squareness, defects English version Door leaves Method for measurement of height, width, thickness and squareness Vantaux de portes Methode de mesure des hauteur, largeur, e paisseur et e querrage Tu rbla tter Meverfahren zu Ermittlung von Ho he, Dicke und Rechtwinkligkeit This European Standard
12、 was approved by CEN on 26 November 1998. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning su
13、ch national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language
14、 and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Swit
15、zerland and United Kingdom.Page 2 EN 951:1998 BSI 05-1999 Foreword This European Standard has been prepared by Technical Committee CEN/TC 33, Doors, windows, shutters and building hardware, the Secretariat of which is held by AFNOR. This European Standard replaces EN 25:1975. This European Standard
16、shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 1999, and conflicting national standards shall be withdrawn at the latest by December 1999. This standard is one of a series of standards for doors. The test method r
17、elates to performance requirements to be published in EN 1529. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece
18、, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.Page 3 EN 951:1998 BSI 05-1999 1 Scope This European Standard applies to all rectangular door leaves and the measurable parameters of doors of other shapes. This standard specifies
19、 the method to be used to measure the dimensions of height, width and thickness, and defects of squareness of door leaves. 2 Apparatus 2.1 Measurement instrument for height and width, steel measuring tape, or similar measuring instrument, accurate to 0,5 mm. 2.2 Measurement instrument for thickness,
20、 micrometer, or similar measuring instrument accurate to 0,01 mm. 2.3 Measurement instrument for squareness, a metal square having two arms with inside reference dimensions of (500 1) mm. The right angle between the arms shall be accurate to 0,1 mm in 500 mm. The square shall incorporate a dial or d
21、igital gauge accurate to 0,1 mm mounted at the 500 mm reference point of one arm (see Figure 1). NOTE An additional block and feeler gauges may be used in place of the dial or digital gauge. 3 Test specimens Test specimens shall be stored and tested in a non-destructive environment within the ranges
22、 of 158C to 308C and 25 % to 75 % relative humidity. Doors which are designed to be glazed, shall be supplied for testing with all glazing carried out in accordance with the door manufacturers specifications. 4 Procedure 4.1 Height and width measurement Measure, to the nearest 1 mm, the height and w
23、idth of each door leaf along lines a-a, b-b, c-c, d-d parallel to, and (20 5) mm from, each edge respectively (see Figure 2). NOTE In the case of a door leaf with rebated edges, the dimensions of height or width should be measured to the inner edges of the rebates. 4.2 Thickness measurement Measure
24、the thickness at 6 points located (20 5) mm from the edges and at the positions indicated in Figure 2, to the nearest 0,1 mm. NOTE If a measuring point occurs where the thickness is not representative of the doors, e.g. because of surface profiles, local adjustment of the measurement position is per
25、mitted. 4.3 Squareness measurement Measure any deviation from squareness of the door leaf at all four corners to the nearest 0,1 mm. 5 Expression of results Record: height and width measurements and maximum deviations in relation to the specified dimensions; thickness measurements and maximum deviat
26、ion in relation to the specified dimension; the four measured values of deviation from squareness. 6 Test report The test report shall contain the following information: a) reference to this European Standard; b) all necessary details to identify the door leaf; c) all relevant details concerning the
27、 type, specified dimensions, materials, form and construction of the door leaf; d) laboratory storage and testing conditions; e) the results expressed as in clause 5; f) name of testing laboratory; g) date of test.Page 4 EN 951:1998 BSI 05-1999 Dimensions in millimetres 1 reference square to calibra
28、te the instrument; 2 max. 0,1 mm deviation from squareness. Figure 1 Measurement instrument for squareness including reference square for calibration Dimensions in millimetres Figure 2 Measuring points and lines for door leafblankBSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | |
29、 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body resp
30、onsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amen
31、dments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be f
32、ound on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards public
33、ations should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards B
34、SI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centr
35、e. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 700
36、1. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or trans
37、mitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.
