BS EN 13045-2009 Packaging - Flexible cylindrical plastic tubes - Dimensions and tolerances《包装 圆柱形塑料软管 尺寸规格和公差》.pdf

上传人:jobexamine331 文档编号:571030 上传时间:2018-12-13 格式:PDF 页数:10 大小:1.14MB
下载 相关 举报
BS EN 13045-2009 Packaging - Flexible cylindrical plastic tubes - Dimensions and tolerances《包装 圆柱形塑料软管 尺寸规格和公差》.pdf_第1页
第1页 / 共10页
BS EN 13045-2009 Packaging - Flexible cylindrical plastic tubes - Dimensions and tolerances《包装 圆柱形塑料软管 尺寸规格和公差》.pdf_第2页
第2页 / 共10页
BS EN 13045-2009 Packaging - Flexible cylindrical plastic tubes - Dimensions and tolerances《包装 圆柱形塑料软管 尺寸规格和公差》.pdf_第3页
第3页 / 共10页
BS EN 13045-2009 Packaging - Flexible cylindrical plastic tubes - Dimensions and tolerances《包装 圆柱形塑料软管 尺寸规格和公差》.pdf_第4页
第4页 / 共10页
BS EN 13045-2009 Packaging - Flexible cylindrical plastic tubes - Dimensions and tolerances《包装 圆柱形塑料软管 尺寸规格和公差》.pdf_第5页
第5页 / 共10页
点击查看更多>>
资源描述

1、BS EN 13045:2009ICS 55.120NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDPackaging Flexible cylindrical plastic tubes Dimensions and tolerancesThis British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 July 2009

2、 BSI 2009ISBN 978 0 580 58511 1Amendments/corrigenda issued since publicationDate CommentsBS EN 13045:2009National forewordThis British Standard is the UK implementation of EN 13045:2009. Itsupersedes BS EN 13045:2000 which is withdrawn.The UK participation in its preparation was entrusted to Techni

3、calCommittee PKW/0/-/10, Plastics.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application. Compliance with a British Stan

4、dard cannot confer immunityfrom legal obligations.BS EN 13045:2009EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 13045April 2009ICS 55.120 Supersedes EN 13045:2000 English VersionPackaging - Flexible cylindrical plastic tubes - Dimensions andtolerancesEmballage - Tubes souples cylindriques plasti

5、ques -Dimensions et tolrancesPackmittel - Zylindrische Kunststofftuben - Mae undGrenzabmaeThis European Standard was approved by CEN on 19 March 2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status o

6、f a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A versi

7、on in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmar

8、k, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEU

9、ROPISCHES KOMITEE FR NORMUNGManagement Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13045:2009: EBS EN 13045:2009EN 13045:2009 (E) 2 Contents Page Foreword . 3 1 Scope . 4 2 Normative

10、 references . 4 3 Terms and definitions 4 4 Dimensions . 5 BS EN 13045:2009EN 13045:2009 (E) 3 Foreword This document (EN 13045:2009) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a nati

11、onal standard, either by publication of an identical text or by endorsement, at the latest by October 2009, and conflicting national standards shall be withdrawn at the latest by October 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of pate

12、nt rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13045:2000. It is based on the professional recommendations of the European Tube Manufacturers Association (ETMA). According to the CEN/CENELEC Internal Regulations,

13、 the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,

14、 Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 13045:2009EN 13045:2009 (E) 4 1 Scope This standard specifies the diameter, length, wall thickness and shoulder geometry of cylindrical plastic flexible tubes. It is applicable to tubes u

15、sed for packing pharmaceutical, cosmetic, hygiene, food and other domestic and industrial products. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the late

16、st edition of the referenced document (including any amendments) applies. EN 12374, Packaging - Flexible tubes Terminology 3 Terms and definitions For the purposes of this standard, the terms and definitions in EN 12374 and the following apply: 3.1 nominal diameter, D diameter d1of the tube measured

17、 at the shoulder 3.2 nominal length, L measured distance between the shoulder and the open end of the tube NOTE Length l1shown in Figure 1. 3.3 thickness of the sleeve, S1thickness of the body wall of the tube BS EN 13045:2009EN 13045:2009 (E) 5 Key 1 Shoulder 2 Nozzle 3 Orifice 4 Body (Tube sleeve)

18、 5 Measurement point for the length of the tube body Figure 1 Cylindrical plastic tube 4 Dimensions All tube dimensions shall be in accordance with Table 1: BS EN 13045:2009EN 13045:2009 (E) 6 Table 1 Dimensions (measurements in mm) Nominal Diameter d1 l1(1) S1 D Diameter Tolerance 100 1mm 1001% Thi

19、ckness Tolerance 13,5 13,5 0,4 40 to 70 0,4 +0,02 -0,04 16 16 55 to 80 19 19 55 to 90 22 22 + 0,3 -0,4 65 to 120 25 25 70 to 135 0,4 to 0,5 + 0,02 -0,05 30 30 70 to 150 35 35 80 to 165 40 40 + 0,1 -0,5 90 to 180 0,5 + 0,02 -0,06 45 45 110 to 175 50 50 120 to 200 0,5 to 0,6 56 56 125 to 200 +0,0 -0,1

20、 60 60 165 to 240 +0,02 -0,05 (1) The figures below represent the range of tube lengths that can be produced for each tube diameter. These measures and tolerances are valid for standard materials like PE-HD, PE-MD, PE-LD and PE-LLD. Other materials may be subject to a mutual agreement between custom

21、er and supplier. BS EN 13045:2009This page has been intentionally left blankBS EN13045:2009BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishSta

22、ndards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant

23、aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0

24、)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should beaddressed to Custom

25、er Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation of those that have been published as Brit

26、ish Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational standards through its Library and its Technical Help to ExportersService. Various BSI electronic information services are also available whichgive details

27、on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developmentsand receive substantial discounts on the purchase price of standards. For detailsof these and other benefits

28、 contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British StandardsOnline can be found at http:/ information about BSI is available on the BSI website at http:/.CopyrightCopyright subsists in all B

29、SI publications. BSI also holds the copyright, in theUK, of the publications of the international standardization bodies. Except aspermitted under the Copyright, Designs and Patents Act 1988 no extract maybe reproduced, stored in a retrieval system or transmitted in any form or by anymeans electroni

30、c, photocopying, recording or otherwise without prior writtenpermission from BSI.This does not preclude the free use, in the course of implementing the standard,of necessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager.Tel: +44 (0)20 8996 7070 Email:

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 标准规范 > 国际标准 > BS

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1