1、BS EN 14635:2010ICS 55.100NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDGlass packaging 26H 126 crown finish DimensionsThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 31 July 2010 BSI 2010ISBN 978 0 580 657
2、29 0Amendments/corrigenda issued since publicationDate CommentsBS EN 14635:2010National forewordThis British Standard is the UK implementation of EN 14635:2010. Itsupersedes BS EN 14635:2006 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee PKW/0/-/7, Pac
3、kaging - Glass.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer i
4、mmunityfrom legal obligations.BS EN 14635:2010EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 14635 June 2010 ICS 55.100 Supersedes EN 14635:2004English Version Glass packaging - 26 H 126 crown finish - Dimensions Emballages en verre - Bague couronne 26 H 126 - Dimensions Verpackungen aus Glas
5、- Kronenmundstck 26 H 126 - Mae This European Standard was approved by CEN on 5 May 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date li
6、sts and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the re
7、sponsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece,
8、 Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management
9、Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14635:2010: EBS EN 14635:2010EN 14635:2010 (E) 2 Contents Page Foreword 3 Introduction .4 1 Scope 5 2 Normative references 5 3 Dimension
10、s .5 Bibliography . 10 BS EN 14635:2010EN 14635:2010 (E) 3 Foreword This document (EN 14635:2010) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication
11、 of an identical text or by endorsement, at the latest by December 2010, and conflicting national standards shall be withdrawn at the latest by December 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shal
12、l not be held responsible for identifying any or all such patent rights. This document supersedes EN 14635:2004. The main technical change from the previous edition is the introduction of a new figure related to the Point “P“. According to the CEN/CENELEC Internal Regulations, the national standards
13、 organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Polan
14、d, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 14635:2010EN 14635:2010 (E) 4 Introduction This document is based on CE.T.I.E. (International Technical Centre for Bottling and related Packaging) data sheet GME 13.02 Revision 1 (2007) 1. Efficient pa
15、ckaging is of great importance for the distribution and the protection of goods. Insufficient or inappropriate packaging can lead to damage or wastage of the contents of the pack. BS EN 14635:2010EN 14635:2010 (E) 5 1 Scope This European standard specifies the dimensions of the 26 mm shallow crown f
16、inish for glass bottles containing beverages. The shallow crown finish is designed to use a metal crown closure (see CE.T.I.E. data sheet EC1-02 revision 1 2). 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only
17、 the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 9058, Glass containers Standard tolerances for bottles 3 Dimensions The design and dimensions of the finish shall be as shown in Figures 1, 2, 3, 4 and 5. Details
18、, which are not specified shall be selected in accordance with the application. For general tolerances see ISO 9058. Dimensions in millimetres minimum through bore 15,5 Key a between 18,5 max and 17 min measured at 3 mm max down from the top Figure 1 Shoulder and bore dimensions Construction limit:
19、certain capping equipment may place further dimensional limits on the neck contour. BS EN 14635:2010EN 14635:2010 (E) 6 Dimensions in millimetres Key a Nominal diameter to suit glass manufacturer. b Detail X: see Figures 4 and 5 c Top of the finish Figure 2 Profile of the finish BS EN 14635:2010EN 1
20、4635:2010 (E) 7 Dimensions in millimetres Key a For optimum performance, the radius should lie between 0,5 and 0,8 excluding the vertical mould joint, and be as near as possible to 0,5. Figure 3 Point “P“ BS EN 14635:2010EN 14635:2010 (E) 8 Dimensions in millimetres Key a Mould parting line of glass
21、 finish b Flat c Glass sealing surface Figure 4 Detail X Glass sealing surface Alternative 1 Contact between the crown cork liner compound and the internal mould parting line of glass finish should be avoided (see CE.T.I.E. data sheets EC1-02 revision 1 2 and EC1-021 3). The sealing surface should b
22、e smooth and free of any defects. BS EN 14635:2010EN 14635:2010 (E) 9 Dimensions in millimetres Key a Mould parting line of glass finish b Flat c Glass sealing surface Figure 5 Detail X Glass sealing surface Alternative 2 Contact between the crown cork liner compound and the internal mould parting l
23、ine of glass finish should be avoided (see CE.T.I.E. data sheets EC1-02 revision 1 2 and EC1-021 3). The sealing surface should be smooth and free of any defects. BS EN 14635:2010EN 14635:2010 (E) 10 Bibliography 1 CE.T.I.E. data sheet GME 13.02 Revision 1, 26 H 126 Crown finish 1)2 CE.T.I.E. EC1-02
24、 revision 1, 26 millimetres crown cork 1)3 CE.T.I.E. EC1-021, 26 millimetres crown cork: main liner profiles 1)1) Obtainable through Centre Technique International de lEmbouteillage (CE.T.I.E), 112-114, rue La Botie, 75008 Paris, France: www.cetie.org, TP: 0033-1-42 65 26 45, TF: 0033-1-40 07 03 21
25、BS EN 14635:2010This page has been intentionally left blank BS EN14635:2010BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards. It prese
26、nts the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to im
27、prove the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. F
28、ax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should beaddressed to Customer Services. Tel
29、: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation of those that have been published as British Standards,un
30、less otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational standards through its Library and its Technical Help to ExportersService. Various BSI electronic information services are also available whichgive details on all its produ
31、cts and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developmentsand receive substantial discounts on the purchase price of standards. For detailsof these and other benefits contact Members
32、hip Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British StandardsOnline can be found at http:/ information about BSI is available on the BSI website at http:/.CopyrightCopyright subsists in all BSI publications.
33、 BSI also holds the copyright, in theUK, of the publications of the international standardization bodies. Except aspermitted under the Copyright, Designs and Patents Act 1988 no extract maybe reproduced, stored in a retrieval system or transmitted in any form or by anymeans electronic, photocopying,
34、 recording or otherwise without prior writtenpermission from BSI.This does not preclude the free use, in the course of implementing the standard,of necessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager.Tel: +44 (0)20 8996 7070 Email:
