1、BSI Standards PublicationBS EN 16291-2:2013Glass packaging Screwfinishes for pressure capsulesPart 2: One way glass MCA 2 finishIncorporating corrigendum August 2014BS EN 16291-2:2013ForewordThis British Standard is the UK implementation of EN 16291-2:2013, incorporating corrigendum August 2014.The
2、UK participation in its preparation was entrusted by Technical Committee PKW/0, Packaging, to Subcommittee PKW/0/-/7, Packaging - Glass.A list of organizations represented on this subcommittee can be obtained on request to its secretary.This publication does not purport to include all the necessary
3、provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2014. Published by BSI Standards Limited 2014ISBN 978 0 580 87782 7ICS 55.100Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was publis
4、hed under the authority of the Standards Policy and Strategy Committee on 31 March 2013.Amendments/corrigenda issued since publicationDate Text affected31 October 2014 Implementation of CEN corrigendum August 2014: Figure 1 replacedBRITISH STANDARDEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN
5、 16291-2 ICS 55.100 English Version Glass packaging - Screw finishes for pressure capsules - Part 2: One way glass MCA 2 finish Emballage en verre - Bagues vis pour capsules pression - Partie 2: Bague MCA 2 pour verre perdu Verpackungen aus Glas - Schraubmundstcke fr Flaschen mit Innendruck - Teil 2
6、: Einweg-MCA 2-Mundstck This European Standard was approved by CEN on 12 January 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists
7、 and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under t
8、he responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugo
9、slav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN
10、 DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16291-2:2013: EIncorporating corrigendum August 2014March 2013BS EN 16291-2:
11、2013EN 16291-2:2013 (E) 2 Contents Page Foreword . 3 Introduction 4 1 Scope 5 2 Terms and definitions 5 3 Dimensions. 5 Bibliography 10 BS EN 16291-2:2013EN 16291-2:2013 (E) 3 Foreword This document (EN 16291-2:2013) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat of
12、 which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2013, and conflicting national standards shall be withdrawn at the latest by September 2013. Attention is drawn t
13、o the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. EN 16291, Glass packaging Screw finishes for pressure capsules, consists of the following parts: Part 1: R
14、eturnable glass MCA 2 finish; Part 2: One way glass MCA 2 finish. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Es
15、tonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 16291-2:2013EN
16、16291-2:2013 (E) 4 Introduction This document is based on CE.T.I.E. (International Technical Centre for Bottling and related Packaging) data sheet GME 320 1. Efficient packaging is of great importance for the distribution and the protection of goods. Insufficient or inappropriate packaging can lead
17、to damage or wastage of the contents of the pack. BS EN 16291-2:2013EN 16291-2:2013 (E) 5 1 Scope This European Standard specifies the dimensions of the screw finish for glass containers designated MCA 2 for one way glass. 2 Terms and definitions For the purposes of this document, the following term
18、 and definition applies. 2.1 MCA (glass) finish designed for the closure of pressurised or vacuum liquids with a tamper-evident closure (metal or plastic) 3 Dimensions The design and dimensions of the finish shall be as shown in Table 1 and Figures 1, 2, 3, 4 and 5. Table 1 Design and dimensions of
19、the finish Pitch TPI cutter 3,175 mm 2 12 8 12,5 mm = Helix angle or angle or fixture to cutter NOTE TPI = threads per inch. One inch is equal to 25,4 mm. The Tan of helix angle for cutter is calculated via the following formula: pitch Tan = (nominal T + nominal E) 2 where T is the thread diameter;
20、E is the wall diameter of threaded finish. The average of the maximum and minimum of “L“ diameter is as close as possible to “L“ nominal. The mean diameter 2min diameter max diameter + Lis in the tolerance of 0,2 mm. Optional: depressed thread at mould parting line (see EN 16292). BS EN 16291-2:2013
21、EN 16291-2:2013 (E) 6 Key N neck (under bead) diameter H thread height S start of thread position from sealing surface to intersection of thread flank F height of the finish L locking bead diameter T thread diameter E wall diameter of threaded finish NOTE Bore diameter: 18,1 mm 1,0 mm for a depth of
22、 3mm. Figure 1 MCA 2 finish Dimensions in millimetres BS EN 16291-2:2013EN 16291-2:2013 (E) 7 Dimensions in millimetres Key a mould parting line b sealing surface The sealing surface is smooth and free of any defects and flash. Figure 2 Possible alternative constructions of the bore entrance to suit
23、 glass manufacturer BS EN 16291-2:2013EN 16291-2:2013 (E) 8 Dimensions in millimetres Minimum through bore 16,0 Figure 3 Detail of the profile BS EN 16291-2:2013EN 16291-2:2013 (E) 9 NOTE Z-Z is the last full depth and width of thread. Beyond this point and Y-Y, the thread root is increased graduall
24、y to full thread diameter T in 90. Figure 4 Run out of thread Dimensions in millimetres Figure 5 Limit of construction BS EN 16291-2:2013EN 16291-2:2013 (E) 10 Bibliography 1 CE.T.I.E. data sheet GME 320 - Pilferproof for pressured beverages1)2 EN 16292, Glass packaging Screw finishes Depressed thre
25、ads 1) Obtainable through Centre Technique International de lEmbouteillage et du Conditionnement (CE.T.I.E), 112- 114, rue La Botie, 75008 Paris, France; www.cetie.org, TP: 0033-1-42 65 26 45, TF: 0033-1-40 07 03 21. This page deliberately left blankBSI is the national body responsible for preparing
26、 British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road Lond
27、on W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our
28、open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or c
29、ontacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and forei
30、gn standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards O
31、nline (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purcha
32、se price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about be
33、coming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure y
34、our documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British
35、Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as
36、 the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means
37、 electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW
