1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 1927-3:2012Monolithic (unshaped) r e f r a c t o r y p r o d u c t sPart 3: Characterization as r e c e i v e dCopyright European Committee for Standardization Provided
2、 by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 1927-3:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO 1927-3:2012. It supersedes BS EN 1402-3:2003, which is withdrawn.The UK par
3、ticipation in its preparation was entrusted to Technical Committee RPI/1, Refractory products and materials.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users
4、 are responsible for its correct application. The British Standards Institution 2012. Published by BSI Standards Limited 2012.ISBN 978 0 580 65758 0 ICS 81.080 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of
5、the Standards Policy and Strategy Committee on 31 January 2013.Amendments issued since publicationDate Text affected Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EUROPEAN STAN
6、DARD NORME EUROPENNE EUROPISCHE NORM EN ISO 1927-3 December 2012 ICS 81.080 Supersedes EN 1402-3:2003English Version Monolithic (unshaped) refractory products - Part 3: Characterization as received (ISO 1927-3:2012) Produits rfractaires monolithiques (non faonns) - Partie 3: Caractrisation ltat de r
7、ception (ISO 1927-3:2012) Ungeformte (monolithische) feuerfeste Erzeugnisse - Teil 3: Prfung im Anlieferungszustand (ISO 1927-3:2012) This European Standard was approved by CEN on 30 November 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditio
8、ns for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in
9、 three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standard
10、s bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Sloven
11、ia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for
12、 CEN national Members. Ref. No. EN ISO 1927-3:2012: ECopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 1927-3:2012 EN ISO 1927-3:2012 (E) 3 Foreword This document (EN ISO
13、 1927-3:2012) has been prepared by Technical Committee ISO/TC 33 “Refractories“ in collaboration with Technical Committee CEN/TC 187 “Refractory products and materials” the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publica
14、tion of an identical text or by endorsement, at the latest by June 2013, and conflicting national standards shall be withdrawn at the latest by June 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall no
15、t be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 1402-3:2003. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgar
16、ia, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turk
17、ey and the United Kingdom. Endorsement notice The text of ISO 1927-3:2012 has been approved by CEN as a EN ISO 1927-3:2012 without any modification. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without li
18、cense from IHS-,-,-BS EN ISO 1927-3:2012ISO 1927-3:2012(E) ISO 2012 All rights reserved iiiContents PageForeword iv1 Scope 12 Normative references . 13 Principle . 24 Sampling 35 Determination of chemical composition . 35.1 Preparation of test sample 35.2 Alumina-silica products . 35.3 Basic product
19、s . 35.4 Special products 35.5 Carbon-containing products 36 Determination of grain-size distribution . 36.1 Principle . 36.2 Apparatus 36.3 Quantity of sample 46.4 Preparation of test samples . 46.5 Procedure 46.6 Expression of results . 67 Determination of moisture content . 67.1 Preparation of te
20、st sample 67.2 Quantity of sample 67.3 Procedure 67.4 Calculation 78 Determination of workability index . 78.1 General . 78.2 Apparatus 78.3 Preparation of test pieces . 98.4 Procedure and calculation 109 Test report .10Annex A (informative) Summary of tests 11Copyright European Committee for Standa
21、rdization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 1927-3:2012ISO 1927-3:2012(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO membe
22、r bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmenta
23、l and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directiv
24、es, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies c
25、asting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.ISO 1927-3 was prepared by Technical Committee ISO/TC 33, Refractories.ISO 1927 consists
26、 of the following parts, under the general title Monolithic (unshaped) refractory products: Part 1: Introduction and classification Part 2: Sampling for testing Part 3: Characterization as received Part 4: Determination of consistency of castables Part 5: Preparation and treatment of test pieces Par
27、t 6: Measurement of physical properties Part 7: Tests on pre-formed shapes Part 8: Determination of complementary propertiesiv ISO 2012 All rights reservedCopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted with
28、out license from IHS-,-,-BS EN ISO 1927-3:2012INTERNATIONAL STANDARD ISO 1927-3:2012(E)Monolithic (unshaped) refractory materials Part 3: Characterization as received1 ScopeThis part of ISO 1927 specifies the methods for the characterization of monolithic (unshaped) refractory materials as received
29、and for checking the homogeneity of a delivery of a product. It is applicable to castables (dense and insulating), gunning materials tap hole clay, injection mixes, dry vibrating mixes, and ramming materials, as defined in ISO 1927-1.NOTE A check list of appropriate tests is given in Annex A.2 Norma
30、tive referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 565, Test sieves Metal wire clo
31、th, perforated metal plate and electroformed sheet Nominal sizes of openingsISO 1927-1, Monolithic (unshaped) refractory products Part 1: Introduction and classificationISO 1927-2, Unshaped refractory materials Part 2: Sampling for testingISO 10058-1, Chemical analysis of magnesite and dolomite refr
32、actory products (alternative to the X-ray fluorescence method) Part 1: Apparatus, reagents, dissolution and determination of gravimetric silicaISO 10058-2, Chemical analysis of magnesite and dolomite refractory products (alternative to the X-ray fluorescence method) Part 2: Wet chemical analysisISO
33、10058-3, Chemical analysis of magnesite and dolomite refractory products (alternative to the X-ray fluorescence method) Part 3: Flame atomic absorption spectrophotometry (FAAS) and inductively coupled plasma atomic emission spectrometry (ICP-AES)ISO 12677, Chemical analysis of refractory products by
34、 XRF Fused cast bead methodISO 14719, Chemical analysis of refractory material, glass and glazes Determination of iron 2+ and iron 3+ by the spectral photometric method with 1-10 phenanthrolineISO 14720-1, Testing of ceramic raw and basic materials Determination of sulfur in powders and granules of
35、non-oxidic ceramic raw and basic materials Part 1: Infrared measurement methodsISO 14720-2, Testing of ceramic raw and basic materials Determination of sulfur in powders and granules of non-oxidic ceramic raw and basic materials Part 2: Inductively coupled plasma atomic emission spectrometry (ICP/AE
36、S) or ion chromatography after burning in an oxygen flowEN 15979, Testing of ceramic raw and basic materials Direct determination of mass fractions of impurities in powders and granules of silicon carbide by OES by DC arc excitationEN 15991,Testing of ceramic and basic materials Direct determination
37、 of mass fractions of impurities in powders and granules of silicon carbide by inductively coupled plasma optical emission spectrometry (ICP OES) with electrothermal vaporisation (ETV) ISO 2012 All rights reserved 1Copyright European Committee for Standardization Provided by IHS under license with C
38、ENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 1927-3:2012ISO 1927-3:2012(E)ISO 20565-1, Chemical analysis of chrome-bearing refractory products and chrome-bearing raw materials (alternative to the X-ray fluorescence method) Part 1: Apparatus, reagents
39、, dissolution and determination of gravimetric silicaISO 20565-2, Chemical analysis of chrome-bearing refractory products and chrome-bearing raw materials (alternative to the X-ray fluorescence method) Part 2: Wet chemical analysisISO 20565-3, Chemical analysis of chrome-bearing refractory products
40、and chrome-bearing raw materials (alternative to the X-ray fluorescence method) Part 3: Flame atomic absorption spectrometry (FAAS) and inductively coupled plasma atomic emission spectrometry (ICP-AES)ISO 21068-1, Chemical analysis of silicon-carbide-containing raw materials and refractory products
41、Part 1: General information and sample preparationISO 21068-2, Chemical analysis of silicon-carbide-containing raw materials and refractory products Part 2: Determination of loss on ignition, total carbon, free carbon and silicon carbide, total and free silica and total and free siliconISO 21068-3,
42、Chemical analysis of silicon-carbide-containing raw materials and refractory products Part 3: Determination of nitrogen, oxygen and metallic and oxidic constituentsISO 21078-1, Determination of boron (III) oxide in refractory products Part 1: Determination of total boron (III) oxide in oxidic materi
43、als for ceramics, glass and glazesISO 21078-2, Determination of boron (III) oxide in refractory products Part 2: Acid extraction method for the determination of boron (III) oxide in binder componentsISO 21079-1, Chemical analysis of refractories containing alumina, zirconia and silica Refractories c
44、ontaining 5 % to 45 % of ZrO2(alternative to the X-ray fluorescence method) Part 1: Apparatus, reagents and dissolutionISO 21079-2, Chemical analysis of refractories containing alumina, zirconia, and silica Refractories containing 5 % to 45 % of ZrO2(alternative to the X-ray fluorescence method) Par
45、t 2: Wet chemical analysisISO 21079-3, Chemical analysis of refractories containing alumina, zirconia, and silica Refractories containing 5 % to 45 % of ZrO2(alternative to the X-ray fluorescence method) Part 3: Flame atomic absorption spectrophotometry (FAAS) and inductively coupled plasma emission
46、 spectrometry (ICP-AES)ISO 21587-1, Chemical analysis of aluminosilicate refractory products (alternative to the X-ray fluorescence method) Part 1: Apparatus, reagents, dissolution and gravimetric silicaISO 21587-2, Chemical analysis of aluminosilicate refractory products (alternative to the X-ray f
47、luorescence method) Part 2: Wet chemical analysisISO 21587-3, Chemical analysis of aluminosilicate refractory products (alternative to the X-ray fluorescence method) Part 3: Inductively coupled plasma and atomic absorption spectrometry methodsISO 26845, Chemical analysis of refractories General requ
48、irements for wet chemical analysis, atomic absorption spectrometry (AAS) and inductively coupled plasma atomic emission spectrometry (ICP-AES) methods3 PrincipleMonolithic (unshaped) refractory products are characterized by making the following determinations:a) chemical composition;b) grain-size distribution by means of sieve analysis;c) moisture content of ramming materials;d) workability index of wet ramming materials.2 ISO 2012 All rights reservedCopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or
