1、BS EN ISO 2398:2016Rubber hoses, textiler e i n f o r c e d , f o r c o m p r e s s e d a i r Specification (ISO 2398:2016)BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN ISO 2398:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementat
2、ion of EN ISO 2398:2016. It supersedes BS EN ISO 2398:2008 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PRI/66, Rubber and plastics tubing, hoses and hose assemblies.A list of organizations represented on this committee can be obtained on request to
3、 its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 89079 6 ICS 23.040.70 Compliance with a British Stan
4、dard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN
5、 ISO 2398 November 2016 ICS 23.040.70 Supersedes EN ISO 2398:2008English Version Rubber hoses, textile-reinforced, for compressed air - Specification (ISO 2398:2016) Tuyaux en caoutchouc renforcs textile pour lair comprim - Spcifications (ISO 2398:2016) Gummischluche mit Textileinlage fr Druckluft -
6、 Anforderung (ISO 2398:2016) This European Standard was approved by CEN on 9 October 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date l
7、ists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation und
8、er the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former
9、Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUR
10、OPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 2398:2016 EBS EN ISO 2398:2016EN ISO 2398:2016 (E) 3 Eur
11、opean foreword This document (EN ISO 2398:2016) has been prepared by Technical Committee ISO/TC 45 “Rubber and rubber products“ in collaboration with Technical Committee CEN/TC 218 “Rubber and plastics hoses and hose assemblies” the secretariat of which is held by BSI. This European Standard shall b
12、e given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2017, and conflicting national standards shall be withdrawn at the latest by May 2017. Attention is drawn to the possibility that some of the elements of this document may be
13、 the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 2398:2008. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to im
14、plement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Roman
15、ia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 2398:2016 has been approved by CEN as EN ISO 2398:2016 without any modification. BS EN ISO 2398:2016ISO 2398:2016(E)Foreword iv1 Scope . 12 Normative references 13 Terms and definiti
16、ons . 14 Classification 25 Materials and construction . 26 Dimensions . 26.1 Inside diameters and tolerances 26.2 Concentricity. 36.3 Tolerance on length . 36.4 Minimum thickness of lining and cover 37 Physical properties 47.1 Rubber compounds . 47.2 Finished hose 48 Frequency of testing 59 Type tes
17、ting 510 Test report or certificate 511 Marking 5Annex A (normative) Type tests and routine tests 6Annex B (informative) Productions acceptance tests . 7Bibliography 8 ISO 2016 All rights reserved iiiContents PageBS EN ISO 2398:2016ISO 2398:2016(E)ForewordISO (the International Organization for Stan
18、dardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right
19、 to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures u
20、sed to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules
21、 of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identifi
22、ed during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on t
23、he meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.The committee responsible for
24、this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 1, Rubber and plastics hoses and hose assemblies.This sixth edition cancels and replaces the fifth edition (ISO 2398:2006), which has been technically revised with the following main changes. Clause 2 has been updated: ISO 1746
25、and ISO 4672 have been deleted and replaced by ISO 10619-1 and ISO 10619-2. ISO 7326:1991 has been replaced by ISO 7326:2006. New clauses (Clause 8, Clause 9 and Clause 10) describing frequency of testing, routine tests, type tests and production acceptance tests have been added. Clause 8 has been r
26、enumbered as Clause 11; a), b), f) and the example have been amended. Annex A and Annex B have been introduced in accordance with ISO/TC 45/SC 1 Guide 976 Rev 7:2013. Clause 10, describing a test report or certificate supplied on request of the purchaser, has been added.iv ISO 2016 All rights reserv
27、edBS EN ISO 2398:2016INTERNATIONAL STANDARD ISO 2398:2016(E)Rubber hoses, textile-reinforced, for compressed air SpecificationWARNING Persons using this document should be familiar with normal laboratory practice. This document does not purport to address all of the safety problems, if any, associat
28、ed with its use. It is the responsibility of the user to establish appropriate health and safety practices and to ensure compliance with any national regulatory conditions.1 ScopeThis document specifies the requirements for three types, three classes and two categories of textile-reinforced rubber h
29、ose for compressed air, up to a maximum working pressure of 25 bar with an operating-temperature range of 40 C to +70 C, depending on the type and category.NOTE 1 bar = 0,1 MPa.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content c
30、onstitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 37, Rubber, vulcanized or thermoplastic Determination of tensile stress-strain propertiesISO 18
31、8, Rubber, vulcanized or thermoplastic Accelerated ageing and heat resistance testsISO 1307, Rubber and plastics hoses Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hosesISO 1402, Rubber and plastics hoses and hose assemblies Hydrostatic testingISO 1817:2015, Rubb
32、er, vulcanized or thermoplastic Determination of the effect of liquidsISO 4671, Rubber and plastics hoses and hose assemblies Methods of measurement of the dimensions of hoses and the lengths of hose assembliesISO 7326:2006, Rubber and plastics hoses Assessment of ozone resistance under static condi
33、tionsISO 8033, Rubber and plastics hoses Determination of adhesion between componentsISO 10619-1, Rubber and plastics hoses and tubing Measurement of flexibility and stiffness Part 1: Bending tests at ambient temperatureISO 10619-2:2011, Rubber and plastics hoses and tubing Measurement of flexibilit
34、y and stiffness Part 2: Bending tests at sub-ambient temperatures3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 8330 apply.ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: availabl
35、e at http:/www.electropedia.org/ ISO Online browsing platform: available at http:/www.iso.org/obp ISO 2016 All rights reserved 1BS EN ISO 2398:2016ISO 2398:2016(E)4 ClassificationHoses are designated as one of the following types, depending on their pressure rating.Type 1: Low pressure designed for
36、a maximum working pressure of 1 MPa (10 bar)Type 2: Medium pressure designed for a maximum working pressure of 1,6 MPa (16 bar)Type 3: High pressure designed for a maximum working pressure of 2,5 MPa (25 bar)These types can be subdivided into three classes depending on their oil resistance.Class A:
37、Non-oil-resistantClass B: Normal oil resistanceClass C: Good oil resistanceThe types and classes above can also be further subdivided into two categories, depending on their operating-temperature range.Categor y N-T (normal temperature): 25 C to +70 CCategor y L-T (low temperature): 40 C to +70 C5 M
38、aterials and constructionThe hose shall consist of a rubber lining, a reinforcement of natural or synthetic textile, applied by any suitable technique, and a rubber cover.The lining and cover shall be of uniform thickness, concentric to comply with the minimum thickness specified, and free from hole
39、s, porosity and other defects. The cover finish may be smooth or fabric-marked.6 Dimensions6.1 Inside diameters and tolerancesWhen measured in accordance with ISO 4671, the inside diameters and their tolerances shall conform to the values specified in Table 1.2 ISO 2016 All rights reservedBS EN ISO
40、2398:2016ISO 2398:2016(E)Table 1 Minimum and maximum inside diametersHose sizeMinimum internal diameter mmMaximum internal diameter mm4 3,25 4,755 4,25 5,756,3 5,55 7,058 7, 25 8,7510 9,25 10,7512,5 11,75 13,2516 15,25 16,7519 18,25 19,7520 19,25 20,7525 23,75 26,2531,5 30,25 32,7538 36,50 39,5040 3
41、8,50 41,5051 49,50 52,5063 61,50 64,5076 74,50 77, 5080 78,00 82,00100 98,00 102,00102 100,00 104,006.2 ConcentricityWhen determined in accordance with ISO 4671, the concentricity, based on a total indicator reading between the inside diameter and the outside surface of the cover, shall be no greate
42、r than 1,0 mm for hoses of inside diameter up to and including 76 mm, and no greater than 1,5 mm for hoses of inside diameter greater than 76 mm.6.3 Tolerance on lengthThe tolerance on cut lengths shall be as specified in ISO 1307, the length being measured in accordance with ISO 4671.6.4 Minimum th
43、ickness of lining and coverWhen measured in accordance with ISO 4671, the minimum thickness of the lining and cover shall be as follows.Type 1: lining 1,0 mmcover 1,5 mmType 2: lining 1,5 mmcover 2,0 mmType 3: lining 2,0 mmcover 2,5 mm ISO 2016 All rights reserved 3BS EN ISO 2398:2016ISO 2398:2016(E
44、)7 Physical properties7.1 Rubber compoundsWhen determined by the methods listed in Table 2, the physical properties of the compounds used for the lining and cover shall conform to the values specified in Table 2.Tests shall be carried out either on samples taken from the hose or from separately vulc
45、anized sheets, 2 mm in thickness and vulcanized to the same cure state as the production hoses.Table 2 Physical properties of rubber compoundsPropertyRequirementTest methodLining CoverMinimum tensile strength 7,0 MPa 7,0 MPa ISO 37 (dumb-bell test piece)Minimum elongation at break 250 % 250 % ISO 37
46、 (dumb-bell test piece)Resistance to ageingChange in tensile strength from original value (max.)25 % 25 %ISO 188 (3 days at 100 C 1 C), air-oven method ISO 37 (dumb-bell test piece)Change in elongation at break from original value (max.)50 % 50 %Resistance to liquidsIncrease in volume (class A) N/A
47、N/A Increase in volume (max.) (class B only)115 % No shrinkage allowedN/AISO 1817:2015 (72 h at 70 C 2 C in oil No. 3), gravimetric methodIncrease in volume (max.) (class C only)30 % No shrinkage allowed75 % No shrinkage allowedISO 1817:2015 (72 h at 70 C 2 C in oil No. 3), gravimetric method7.2 Fin
48、ished hoseWhen determined by the methods listed in Table 3, the physical properties of the finished hose shall conform to the values specified in Table 3.Table 3 Physical properties of finished hoseProperty Requirement Test methodProof pressureMPa barISO 1402type 1 2 20type 2 3,2 32type 3 5 50Change
49、 in length at maximum working pressure5 % ISO 1402Change in diameter at maximum working pressure5 % ISO 1402Minimum burst pressureMPa barISO 1402type 1 4 40type 2 6,4 64type 3 10 100Adhesion between components 2,0 kN/m (min.) ISO 80334 ISO 2016 All rights reservedBS EN ISO 2398:2016ISO 2398:2016(E)Property Requirement Test methodOzone resistanceNo cracking observed under 2 magnificationISO 7326:2006 method 1 (up to 25 mm id) method 2 or 3 for other sizesFlexibility
