1、BS EN ISO13229:2011ICS 23.040.20; 91.140.80NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDThermoplastics pipingsystems for non-pressure applications Unplasticizedpoly(vinyl chloride)(PVC-U) pipesand fittings Determination of theviscosity number andK-valueProvid
2、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-National forewordThis British Standard is the UK implementation of EN ISO 13229:2011. It supersedes BS EN 922:1995 and BS ISO 13229:2010, which are withdrawn.The UK participation in its preparation was entrus
3、ted to Technical Committee PRI/88/1, Plastics piping for non-pressure applications.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its
4、correct application.Compliance with a British Standard cannot confer immunity from legal obligations. BS EN ISO 13229:2011This British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 30 June2010 BSI 2011ISBN 978 0 580 73955 2Amendments/corrigenda issued since
5、 publicationDate Comments 31 October 2011 This corrigendum renumbers BS ISO 13229:2010 as BS EN ISO 13229:2011Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 13229 September 2011 ICS 23.040.20;
6、 91.140.80 Supersedes EN 922:1994English Version Thermoplastics piping systems for non-pressure applications - Unplasticized poly(vinyl chloride) (PVC-U) pipes and fittings - Determination of the viscosity number and K-value (ISO 13229:2010) Systmes de canalisations thermoplastiques pour application
7、s sans pression - Tubes et raccords en poly(chlorure de vinyle) non plastifi (PVC-U) - Dtermination de lindice de viscosit rduite et de la valeur K (ISO 13229:2010) Rohrleitungssysteme aus Thermoplasten fr drucklose Anwendungen - Rohre und Formstcke aus weichmacherfreiem Polyvinylchlorid (PVC-U) - B
8、estimmung der Viskosittszahl und Berechnung des K-Wertes (ISO 13229:2010) This European Standard was approved by CEN on 11 August 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national
9、standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version
10、in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
11、 Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROP
12、EN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 13229:2011: EProvided by IHSNot for ResaleNo reproduction or networkin
13、g permitted without license from IHS-,-,-Foreword The text of ISO 13229:2010 has been prepared by Technical Committee ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids” of the International Organization for Standardization (ISO) and has been taken over as EN ISO 13229:2011
14、by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2012, and conflicting
15、 national standards shall be withdrawn at the latest by March 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supe
16、rsedes EN 922:1994. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hunga
17、ry, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 13229:2010 has been approved by CEN as a EN ISO 13229:2011 without any modifica
18、tion. BS EN ISO 13229:2011 EN ISO 13229:2011 (E)Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-INTERNATIONAL STANDARD1Thermoplastics piping systems for non-pressure applications Unplasticized poly(vinyl chloride) (PVC-U) pipes and fittings Determina
19、tion of the viscosity number and K-value 1 Scope This International Standard specifies a method for the determination of the viscosity number (also known as reduced viscosity) and K-value of an unplasticized poly(vinyl chloride) (PVC) resin derived from a pipe, fitting or compound. In this Internati
20、onal Standard, only the method for isolation (or separation) of the PVC resin is detailed, while the determination of the viscosity number is given in ISO 1628-2. The presence of other additives or polymers can invalidate this method (see Clause 3). 2 Normative references The following referenced do
21、cuments are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1628-2, Plastics Determination of the viscosity of polymers in dilute so
22、lution using capillary viscometers Part 2: Poly(vinyl chloride) resins 3 Principle A PVC resin, contained in a sample taken from a pipe, a fitting or a compound, is separated from most additives by dissolution in tetrahydrofuran (THF) and precipitation by methanol from a portion of the solution that
23、 has been isolated by centrifuging and decantation. The presence of additives in injection-moulding compounds can affect the results for materials for/from injection-moulded fittings. If other polymers soluble in THF and insoluble in methanol (e.g. PMMA material) are present, this method shall not b
24、e used. The precipitate is used for estimation of the viscosity number and K-value in accordance with ISO 1628-2. 4 Reagents for isolation or separation of the PVC resin 4.1 Tetrahydrofuran (THF), stabilized. WARNING It is very important for safety reasons that personal protective clothing be used w
25、hen applying solvents to the test specimen. The use of solvents in regard to application of this International Standard may be further controlled under national and/or regional legislation. In particular, the THF used shall be collected, stored and sent to solvent recovery. 4.2 Methanol. BS EN ISO 1
26、3229:2011 EN ISO 13229:2011 (E) ISO 2011Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2 5 Apparatus for isolation or separation of the PVC resin 5.1 Glass container, of minimum capacity 100 ml. 5.2 Magnetic stirrer, with an adjustable speed of 0 r/
27、min to 1 200 r/min. 5.3 Glass beaker, of capacity 600 ml, tall form. 5.4 Filter funnel. 5.5 Laboratory filter paper, capable of retaining polymer precipitated in accordance with 6.1. 5.6 Centrifuge with tubes, for 50 ml. 5.7 Vacuum dessicator. 5.8 Water bath, if necessary (see 6.1). 5.9 Pasteur pipe
28、tte, if necessary (see 6.1). 6 Procedure 6.1 Isolation or separation of the PVC resin Take approximately 2 g of PVC compound (2,5 g if the filler content is expected to be high), cut, if necessary, from the pipe or fitting tested. Dissolve it in approximately 50 ml of THF in the glass container (5.1
29、) by stirring. If the dissolution occurs slowly, warm carefully in a water bath (5.8). The PVC resin shall be completely dissolved before continuing the procedure. Transfer the solution to a tube of the centrifuge (5.6) and operate the centrifuge for approximately 40 min. Decant that part of THF sol
30、ution free of particles into the glass beaker (5.3), if necessary using a pasteur pipette (5.9), without entraining any filler. In the beaker, precipitate the polymer by carefully adding methanol and stirring, until 10 parts of methanol have been added per part of THF solution. Filter the suspension
31、 using a filter paper (5.5) and wash the precipitate with methanol. Transfer the precipitated polymer, but not the filter paper, to a bowl and dry at 50 C for at least 12 h in the vacuum dessicator (5.7). 6.2 Determination of the viscosity number Determine and record the viscosity number, in millili
32、tres per gram, in accordance with ISO 1628-2 using a resin sample of (0,250 0,000 25) g by dissolution in cyclohexanone. BS EN ISO 13229:2011 EN ISO 13229:2011 (E) ISO 2011Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-37 Calculation of K-value Calc
33、ulate the K-value of the PVC resin using Equation (1): 0,50001, 5 l g 1 1 4 0 2 1, 5 l g 1, 5 l g1 000151,5tttK+ + += (1) where t is the efflux time of the solution, in seconds; t0is the efflux time of the solvent, in seconds. Annex A gives the relation between the K-value and the viscosity number (
34、reduced viscosity) for PVC resin. 8 Accuracy The accuracy of the method for the determination of the K-value is 2. 9 Test report The test report shall include the following information: a) a reference to this International Standard, i.e. ISO 13229:2010, and the referring standard; b) complete identi
35、fication of the pipe, fitting or compound tested; c) the viscosity number; d) the K-value; e) any factor that could have affected the results, such as any incident or any operating details not specified in this International Standard; f) the date of the test. BS EN ISO 13229:2011 EN ISO 13229:2011 (
36、E) ISO 2011Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-4 Annex A (informative) Relationship between K-value and viscosity number for PVC resin For a PVC resin, the K-value according to Fikentscher1is calculated according to Equation (1). For conv
37、enience, the K-values corresponding to a viscosity number from 60 ml/g to 178 ml/g for a solution in cyclohexanone containing 5 g resin/litre are given in Table A.1. Table A.1 Viscosity numbers and corresponding K-values Viscosity number ml/g K-value Viscosity numberml/g K-value Viscosity number ml/
38、g K-value 60 62 64 66 68 70 72 74 76 78 80 82 84 86 88 90 92 94 96 98 49,6 50,5 51,3 52,1 52,8 53,6 54,3 55,1 55,8 56,5 57,2 57,9 58,5 59,2 59,8 60,5 61,1 61,7 62,3 62,9 100 102 104 106 108 110 112 114 116 118 120 122 124 126 128 130 132 134 136 138 63,5 64,1 64,7 65,2 65,8 66,3 66,9 67,4 67,9 68,5
39、69,0 69,5 70,0 70,5 71,0 71,5 71,9 72,4 72,9 73,3 140 142 144 146 148 150 152 154 156 158 160 162 164 166 168 170 172 174 176 178 73,8 74,3 74,7 75,1 75,6 76,0 76,5 76,9 77,3 77,7 78,1 78,5 78,9 79,3 79,7 80,1 80,5 80,9 81,3 81,7 BS EN ISO 13229:2011 EN ISO 13229:2011 (E) ISO 2011Provided by IHSNot
40、for ResaleNo reproduction or networking permitted without license from IHS-,-,-5Bibliography 1 FIKENTSCHER, H. Cellulosa chemie, No. 13, 1932, pp. 58-64 BS EN ISO 13229:2011 EN ISO 13229:2011 (E) ISO 2011Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-
41、,-ICS 23.040.20; 91.140.80 Price based on 5 pages BS EN ISO 13229:2011 EN ISO 13229:2011 (E) ISO 2011Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-This page has been intentionally left blankProvided by IHSNot for ResaleNo reproduction or networking
42、 permitted without license from IHS-,-,-BSI GroupHeadquarters 389 Chiswick High Road, London, W4 4AL, UK Tel +44 (0)20 8996 9001 Fax +44 (0)20 8996 7001 standardsBSI - British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK v
43、iew on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the
44、 quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +
45、44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +
46、44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001 Email: You may also buy directly using a debit/credit card from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, u
47、nless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its p
48、roducts and services. Contact Information Centre. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online acces
