1、BRITISH STANDARD BS ISO 1268-1:2001 Fibre-reinforced plastics Methods of producing test plates Part 1: General conditions ICS 83.120 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS ISO 1268-1:2001 This British Standard, having been prepared under the direction of the Materia
2、ls and Chemicals Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 30 January 2002 BSI 30 January 2002 ISBN 0 580 38902 2 National foreword This British Standard reproduces verbatim ISO 1268-1:2001 and implements it as the UK na
3、tional standard. The UK participation in its preparation was entrusted to Technical Committee PRI/42, Fibre reinforced thermosetting plastics and prepregs, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-refere
4、nces The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalo
5、gue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text
6、; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cove
7、r, an inside front cover, the ISO title page, pages ii to iv, pages 1 to 4, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date Comments Reference number ISO 1268-1:200
8、1(E)INTERNATIONAL STANDARD ISO 1268-1 First edition 2001-12-01 Fibre-reinforced plastics Methods of producing test plates Part 1: General conditions Plastiques renforcs de fibres Mthodes de fabrication de plaques dessai Partie 1: Conditions gnrales ISO 1268-1:2001(E) ii ISO 1268-1:2001(E) iiiContent
9、s Page Foreword.iv 1 Scope1 2 Normative references1 3 Terms and definitions .2 4 Health and safety.2 5 Principle2 6 Raw materials and semi-finished products 2 7 Plate dimensions.2 8 Reinforcement2 9 General requirements for the laboratory/workshop apparatus 2 10 Procedure.3 11 Verification of the ch
10、aracteristics of the plates obtained .3 12 Marking.3 13 Test plate preparation report4 ISO 1268-1:2001(E) iv Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is
11、normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part
12、in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. The main task of technical committees is to pre
13、pare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that
14、some of the elements of this part of ISO 1268 may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 1268-1 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 13, Composites and reinforcement fibres. Together wi
15、th the other parts (see below), this part of ISO 1268 cancels and replaces ISO 1268:1974, which has been technically revised. ISO 1268 consists of the following parts, under the general title Fibre-reinforced plastics Methods of producing test plates: Part 1: General conditions Part 2: Contact and s
16、pray-up moulding Part 3: Wet compression moulding Part 4: Moulding of prepregs Part 5: Filament winding Part 6: Pultrusion moulding Part 7: Resin transfer moulding Part 8: Compression moulding of SMC and BMC Part 9: Moulding of GMT/STC Part 10: Injection moulding of SMC and other long-fibre moulding
17、 compounds General principles and moulding of multipurpose test specimens Part 11: Injection moulding of SMC and other long-fibre moulding compounds Small plates INTERNATIONAL STANDARD ISO 1268-1:2001(E)1Fibre-reinforced plastics Methods of producing test plates Part 1: General conditions 1 Scope Th
18、e various parts of ISO 1268 (see the foreword) describe methods used to prepare reinforced-plastics plates from which test specimens can be cut. This allows the properties of a composite, or the constituents of the composite, to be determined. The methods are intended to cover all the main types of
19、reinforcement and resin matrix. The choice of test plate preparation method depends on: a) the reinforcement: its nature (glass, carbon, aramid, etc.); its form (roving, mat, woven fabric, etc.); its orientation with respect to the length, width and thickness of the plate; its content in the reinfor
20、ced plastic; b) the matrix (thermosetting or thermoplastic); c) the magnitude expected for the properties; d) the production process that is to be evaluated. Since the mechanical properties of a reinforced plastic are known to be dependent on the process by which the plastic is produced, it is recom
21、mended that the test plates be prepared, if possible, by the same method that will be used to produce the plastic. This part of ISO 1268 describes the general requirements common to all the methods. 2 Normative references The following normative documents contain provisions which, through reference
22、in this text, constitute provisions of this part of ISO 1268. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of ISO 1268 are encouraged to investigate the possibility of applying the most rece
23、nt editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 472, Plastics Vocabulary ISO 1172, Textile-glass-reinforced plas
24、tics Prepregs, moulding compounds and laminates Determination of the textile-glass and mineral-filler content Calcination methods ISO 1268-1:2001(E) 2 ISO 1183 (all parts), Plastics Methods for determining the density of non-cellular plastics ISO 7822, Textile glass reinforced plastics Determination
25、 of void content Loss on ignition, mechanical disintegration and statistical counting methods ISO 10724-2:1998, Plastics Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) Part 2: Small plates 3 Terms and definitions For the purposes of this part of ISO 1268, the
26、terms and definitions given in ISO 472 apply. Each subsequent part of ISO 1268 gives, where necessary, the definitions of specific terms it needs to introduce. 4 Health and safety The various parts of ISO 1268 are limited to describing test plate preparation methods. The conditions under which the m
27、aterials used are handled shall comply with the national regulations in force in each country and the staff shall be informed of the hazards involved and appropriate precautions taken. 5 Principle Subsequent parts of this International Standard describe the basic methods utilized to produce test pla
28、tes. 6 Raw materials and semi-finished products All the materials used (reinforcements, resins, additives; SMC, BMC, prepregs, etc.) shall be identified in a precise manner. They shall be stored under the conditions recommended by the manufacturer and shall be used before the expiration date marked
29、on the label. 7 Plate dimensions The length, width and thickness of the plates produced will depend on the material being processed and the method used to produce them. The dimensions shall be as specified in the relevant part of this Intenational Standard. NOTE The plate dimensions will also depend
30、 on the test which will be conducted on the test specimens cut from the plates. For example, a square plate of side at least 250 mm is required to perform tensile tests in two perpendicular directions. 8 Reinforcement The reinforcement content of the plate shall be the same as in the finished produc
31、ts whose properties are to be evaluated. In the absence of particular specifications, use the recommended content given in the relevant part of this International Standard. 9 General requirements for the laboratory/workshop apparatus Unless otherwise specified, the apparatus used to produce the plat
32、es shall be capable of maintaining the required temperatures and pressures to within the accuracy prescribed for the chosen plate production method. ISO 1268-1:2001(E) 3The laboratory/workshop shall be equipped with monitoring equipment which will enable the production temperature and pressure to be
33、 recorded as a function of time. 10 Procedure The procedure used to prepare the test plates will differ depending on the process and materials used. The procedure to be followed for a particular plate production method is described in the relevant part of this International Standard. 11 Verification
34、 of the characteristics of the plates obtained 11.1 General The plates obtained shall be inspected prior to cutting out test specimens. The criteria for acceptance or rejection of a plate shall be as defined in the materials specifications and in the plate production method, or as agreed between the
35、 interested parties. 11.2 Fibre content The fibre content shall be determined in accordance with ISO 1172 for glass-reinforced plastics and by a method agreed on between the interested parties for carbon-reinforced plastics. The lay-up sequence can be determined by examination of the residue. 11.3 D
36、egree of porosity or void content The degree of porosity, or void content, is a measure of the frequency of occurrence of open or closed cavities in the plate. Any of several methods may be used to determine it: visual examination, examination of a polished cross-section using a microscope (see ISO
37、7822), ultrasonic examination or X-ray examination. 11.4 Density The density may be determined in accordance with the appropriate part of ISO 1183. 11.5 Dimensions The thickness of the plates shall be measured and, where necessary, the other dimensions. 12 Marking Each plate shall be marked to allow
38、 the identification of the mould or the mould cavity used; the side of the plate; the lay-up sequence, if required; the orientation of the plate with respect to the melt flow direction, or to any other direction specific to the material or the method of production. ISO 1268-1:2001(E) 4 The system of
39、 lines (thin or broad, single or multiple) described in ISO 10724-2:1998, annex C, shall be used. In addition, plates shall have markings enabling the plate preparation report to be easily traced. 13 Test plate preparation report The test plate preparation report shall indicate the following informa
40、tion: a) a reference to the relevant part of this International Standard; b) the place and date of production of the plate or plates; c) a full description of the materials used, including details of resins, reinforcements, fillers, etc.; d) the composition of the resin system used, where applicable
41、; e) a description of the equipment used; f) details of the operating conditions; g) details of the lay-up of the plate or plates; h) the values of the test plate characteristics (e.g. thickness, fibre content) which the relevant part of this International Standard requires to be determined and any
42、other characteristics when applicable (see clause 11); i) any other information needed to reproduce the plates exactly; j) any deviations from the relevant part of this International Standard. blankBS ISO 1268-1:2001 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is t
43、he independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure
44、that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsibl
45、e, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BS
46、I, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI polic
47、y to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service.
48、Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and rece
49、ive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright s
