1、BS ISO 13775-2:2016Thermoplastic tubing andhoses for automotive usePart 2: Petroleum-based-fuel applicationsBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS ISO 13775-2:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 1377
2、5-2:2016. It supersedes BS ISO 13775-2:2000 which is withdrawn. The UK participation in its preparation was entrusted to TechnicalCommittee PRI/66, Rubber and plastics tubing, hoses and hoseassemblies.A list of organizations represented on this committee can beobtained on request to its secretary.Th
3、is publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2016. Published by BSI Standards Limited 2016ISBN 978 0 580 86680 7ICS 23.040.70; 43.060.40Compliance with a British Standard cann
4、ot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 December 2016.Amendments/Corrigenda issued since publicationDate Text affectedBS ISO 13775-2:2016 ISO 2016Thermoplastic tubing and hoses for automotive
5、 use Part 2: Petroleum-based-fuel applicationsTubes et tuyaux en thermoplastique pour lindustrie automobile Partie 2: Applications pour carburants base de ptroleINTERNATIONAL STANDARDISO13775-2Second edition2016-12-15Reference numberISO 13775-2:2016(E)BS ISO 13775-2:2016ISO 13775-2:2016(E)ii ISO 201
6、6 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2016, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the in
7、ternet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47cop
8、yrightiso.orgwww.iso.orgBS ISO 13775-2:2016ISO 13775-2:2016(E)Foreword ivIntroduction v1 Scope . 12 Normative references 13 Classification and materials . 14 Dimensions . 25 Requirements 26 Frequency of testing 47 Marking 4Annex A (informative) Example of how a non-standard type of tubing or hose co
9、uld be specified using a matrix 6Annex B (normative) Method for determining the resistance to surface-contaminating fluids 7Annex C (normative) Method of test for flame resistance 8Annex D (normative) Cleanliness and extractables test .14Annex E (normative) Type tests .16Annex F (normative) Routine
10、tests17Annex G (informative) Production tests.18Bibliography .19 ISO 2016 All rights reserved iiiContents PageBS ISO 13775-2:2016ISO 13775-2:2016(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of
11、 preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental
12、, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO
13、/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibilit
14、y that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of pate
15、nt declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as inform
16、ation about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.The committee responsible for this document is ISO/TC 45, Rubber and rubber products, Subcommittee SC 1, Rubber and plastics hoses
17、 and hose assemblies.This second edition cancels and replaces the first edition (ISO 13775-2:2000), which has been technically revised.ISO 13775 consists of the following parts, under the general title Thermoplastic tubing and hoses for automotive use: Part 1: Non-fuel applications Part 2: Petroleum
18、-based-fuel applicationsiv ISO 2016 All rights reservedBS ISO 13775-2:2016ISO 13775-2:2016(E)IntroductionThis part of ISO 13775 defines the requirements of extruded thermoplastic tubing/hoses for petroleum-based-fuel applications for automotive use. In addition, it can also be applied as a classific
19、ation system to enable original equipment manufacturers (OEMs) to detail a “line call-out” of tests for specific applications where these are not covered by the six main types (see example in Annex A). In this case, the tubing or hose would not carry any marking showing this ISO specification number
20、, but could detail the OEMs own identification markings as shown on their part drawings. ISO 2016 All rights reserved vBS ISO 13775-2:2016BS ISO 13775-2:2016Thermoplastic tubing and hoses for automotive use Part 2: Petroleum-based-fuel applicationsWARNING Persons using this part of ISO 13775 should
21、be familiar with normal laboratory practice. This part of ISO 13775 does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate safety and health practices and to ensure compliance with any national regulatory
22、 conditions.1 ScopeThis part of ISO 13775 specifies test requirements and test methods for extruded thermoplastic tubing and hoses for use in petroleum-based-fuel lines in vehicles powered by internal-combustion engines.2 Normative referencesThe following documents, in whole or in part, are normativ
23、ely referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 188, Rubber, vulcanized or thermoplastic Accelerated ageing an
24、d heat resistance testsISO 1402, Rubber and plastics hoses and hose assemblies Hydrostatic testingISO 1817, Rubber, vulcanized or thermoplastic Determination of the effect of liquidsISO 4926, Road vehicles Hydraulic braking systems Non-petroleum-base reference fluidsISO 7628, Road vehicles Thermopla
25、stics tubing for air braking systemsISO 8031:2009, Rubber and plastics hoses and hose assemblies Determination of electrical resistance and conductivityISO 8033, Rubber and plastics hoses Determination of adhesion between componentsISO 8308, Rubber and plastics hoses and tubing Determination of tran
26、smission of liquids through hose and tubing wallsISO 10619-1, Rubber and plastics hoses and tubing Measurement of flexibility and stiffness Part 1: Bending tests at ambient temperatureISO 19013-2:2016, Rubber hoses and tubing for fuel circuits for internal combustion engines Specification Part 2: Ga
27、soline fuelsISO 30013, Rubber and plastics hoses Methods of exposure to laboratory light sources Determination of changes in colour, appearance and other physical propertiesSAE J2260, Non-metallic Fuel System Tubing with One or More Layers3 Classification and materialsThe product shall consist of an
28、 extruded thermoplastic material with or without an integral reinforcement. The product may also have an inner veneer to impart improved fluid resistance and/or INTERNATIONAL STANDARD ISO 13775-2:2016(E) ISO 2016 All rights reserved 1BS ISO 13775-2:2016ISO 13775-2:2016(E)reduced fuel vapour permeabi
29、lity. It may also have an extruded outer cover to improve environmental resistance and/or flame resistance. The outer cover is not necessarily bonded to the tubing or hose.Six types of tubing and hose for specific applications are specified as follows: Type 1: feed and return lines from the fuel tan
30、k to the engine compartment gasoline engines; Type 2: feed and return lines from the fuel tank to the engine compartment diesel engines; Type 3: feed and return lines in the engine compartment moderate-temperature (100 C) environment gasoline engines; Type 4: feed and return lines in the engine comp
31、artment high-temperature (125 C) environment gasoline engines; Type 5: feed lines in the engine compartment diesel engines; Type 6: multi-layer tubing or hoses for vapour lines.4 DimensionsDiameters and wall thicknesses shall be as given in Table 1.The wall thickness shall be the sum of the individu
32、al thicknesses of the various elements in the construction of the tubing or hose. The thickness of each individual element shall be such that it is able to carry out its own function and the total function of the tubing or hose.Table 1 Nominal sizes, internal diameters and wall thicknessesNominal si
33、ze Internal diameter mmWall thickness (min) mm2 2 0,1 0,94 4 0,1 0,96 6 0,1 0,96 6 0,1 1,357, 5 7,5 0,1 1,128 8 0,1 0,98 8 0,1 1,359 9 0,1 1,3510 10 0,1 1,812 12 0,1 1,3512 12 0,1 1,814 14 0,1 1,85 RequirementsThe following tests shall be selected for each application of the tubing or hose, based on
34、 the performance requirements of the finished product. The tests to be carried out for each type of tubing or hose classified in Clause 3 are given in Table E.1.a) Burst pressure: When determined in accordance with ISO 1402, the minimum burst pressure for all constructions shall be 5,5 MPa gauge (55
35、 bar).b) Cold impact resistance: After cold impact testing at 40 C in accordance with ISO 7628, all constructions shall show no evidence of external fracture or cracking and shall meet the burst pressure requirements of a).2 ISO 2016 All rights reservedBS ISO 13775-2:2016ISO 13775-2:2016(E)c) Heat a
36、geing resistance: After ageing at one or more of the following sets of conditions in accordance with ISO 188, all constructions shall meet the cold impact requirements of b):1) 1 000 h at 70 C;2) 1 000 h at 100 C;3) 1 000 h at 125 C;4) 168 h at 100 C;5) 168 h at 125 C;6) 168 h at 140 C.d) Resistance
37、 to light: All constructions shall meet the cold impact requirements of b) after 1 000 kJ/m2xenon-arc exposure in accordance with ISO 30013.NOTE This test is for applications that require exposure to daylight either during normal vehicle usage or on chassis that can be stored in the open prior to fi
38、nal assembly of the vehicle.e) Resistance to fuels: When tested in accordance with SAE J2260, for 1 000 h at 60 C 2 C, using one or more of the following test fuels, all constructions shall meet the cold impact requirements of b) and the adhesion requirements of k) where applicable:1) a mixture of 8
39、5 % by volume of liquid C (ISO 1817) and 15 % by volume of methanol;2) a mixture of 75 % by volume of liquid C (ISO 1817) and 25 % by volume of methanol;3) a mixture of 50 % by volume of liquid C (ISO 1817) and 50 % by volume of methanol;4) a mixture of 15 % by volume of liquid C (ISO 1817) and 85 %
40、 by volume of methanol;5) by volume 100 % liquid 2 (ISO 1817);6) a mixture of 90 % by volume of liquid 2 (ISO 1817) and 10 % by volume of ethanol;7) liquid F (ISO 1817) (simulated diesel fuel);8) a mixture of 90 % by volume of liquid F (ISO 1817) and 10 % by volume of rape seed methyl ester;9) a mix
41、ture of 80 % by volume of liquid F (ISO 1817) and 20 % by volume of rape seed methyl ester;10) PN 180 oxidized fuel in accordance with ISO 19013-2:2016, Annex D.f) Volume change in the test fluids: Determine the change in volume of the hose (tube and cover) by the procedure described in ISO 1817. Pl
42、ace the test pieces in test liquids as specified in e) at a temperature of 40 C 2 C for 40 d. If the hose is made of a homogeneous compound (with or without reinforcement), the swelling shall not exceed 35 % by volume, as measured by displacement in water. For hose with an inner layer of fuel-resist
43、ance material and a cover of another material, mainly intended for weather and ozone resistance, the increase in volume shall not exceed 35 % for the tube and 120 % for the cover.g) Resistance to stress cracking: When tested in accordance with ISO 7628, all constructions shall show no evidence of st
44、ress cracking and shall meet the cold impact requirements of b).h) Resistance to battery acid: When tested in accordance with ISO 7628, all constructions shall show no evidence of cracking or degradation and shall meet the cold impact requirements of b).i) Resistance to surface contamination by engi
45、ne oil and petroleum-based hydraulic fluid: When tested in accordance with Annex B, using ISO 1817 Oil No. 3, all constructions shall meet the cold impact requirements of b) and the adhesion requirements of k) where applicable. ISO 2016 All rights reserved 3BS ISO 13775-2:2016ISO 13775-2:2016(E)j) R
46、esistance to surface contamination by non-petroleum hydraulic (brake/clutch) fluid: When testedin accordance with Annex B, using hydraulic fluid in accordance with ISO 4926, all constructionsshall meet the cold impact requirements of b) and the adhesion requirements of k) where applicable.k) Adhesio
47、n: For any constructions with two or more co-extruded or bonded layers only: Whendetermined in accordance with the appropriate procedure of ISO 8033, the separation forcebetween bonded layers shall not be less than 1,5 kN/m.l) Flame resistance: When tested in accordance with Annex C, the tubing or h
48、ose shall withstand aminimum of 60 s exposure to flame without loss of pressure.m) Internal cleanliness: When determined in accordance with Annex D, the insoluble impurities shallnot exceed 5 g/m2and the fuel-soluble impurities shall not exceed 3 g/m2.n) Fuel permeability: When determined in accorda
49、nce with ISO 8308, the permeability to a mixtureof 85 % by volume of liquid C (ISO 1817) and 15 % by volume of methanol shall not exceed25 g/m2/24 h.o) Electrical resistance: When determined in accordance with ISO 8031:2009, 4.5, 4.6, or 4.7, theelectrical resistance shall not exceed 10 M.p) Resistance to kinking: When determined in accordance with ISO 10619-1, the maximum coefficientof deformation (T/D) shall not exceed 0,7.The mandrel diameter shall be 1
