CSN 01 3473-1989 Drawings of melioration works《改良工程图纸》.pdf

相关资源

GB T 10992.3-1999 静电复印机 工程图纸复印机.pdf

GB T 10992.3-2008 静电复印机.第3部分 工程图纸复印机.pdf

ARMY MIL-HDBK-400 VALID NOTICE 2-2004 CRITERIA FOR PREPARATION OF GEAR AND SPLINE ENGINEERING DRAWINGS《齿轮编制和花键工程图纸准则》.pdf

ARMY MIL-HDBK-400 NOTICE 1-1988 CRITERIA FOR PREPARATION OF GEAR AND SPLINE ENGINEERING DRAWINGS《齿轮编制和花键工程图纸准则》.pdf

BS 2856-1973 Precise conversion of inch and metric sizes on engineering drawings《工程图纸的英制与公制尺寸的精确换算》.pdf

CSN 01 3228 Za-1982 《修订a 1 1982捷克国家标准01 3228 ST SEV 650-77工程图纸 沟槽连接规则》.pdf

CSN 01 3216 Za-1984 《修订a） 10 1984 捷克国家标准 01 3216 ★ ST SEV 859-78 工程图纸，齿轮绘制规则》.pdf

DIN 19052-1-1979 Microfilming of engineering drawings on microfilm 35 mm technical proceeding dimensions《35mm缩微胶片工程图纸的缩微技术 第1部分 技术程序 尺寸》.pdf

DIN 19052-4-1979 Microfilming of engineering drawings division system of drawings for recording on film 35 mm《工程图纸的缩微技术 第4部分 35mm缩微胶片图纸录制的分段方法》.pdf

猜你喜欢

ASTM A1016 A1016M-2017a Standard Specification for General Requirements for Ferritic Alloy Steel Austenitic Alloy Steel and Stainless Steel Tubes《铁素体合金钢管 奥氏体合金钢管和不锈钢管通用要求的标准规格》.pdf

ASTM A1016 A1016M-2018 Standard Specification for General Requirements for Ferritic Alloy Steel Austenitic Alloy Steel and Stainless Steel Tubes《铁素体合金钢奥氏体合金钢和不锈钢管通用要求的标准规范》.pdf

ASTM A1017 A1017M-2007 Standard Specification for Pressure Vessel Plates Alloy Steel Chromium-Molybdenum-Tungsten《铬钼钨合金钢制压力容器板的标准规范》.pdf

ASTM A1017 A1017M-2011 Standard Specification for Pressure Vessel Plates Alloy Steel Chromium-Molybdenum-Tungsten《铬钼钨合金钢制压力容器板标准规格》.pdf

ASTM A1017 A1017M-2011(2015) Standard Specification for Pressure Vessel Plates Alloy Steel Chromium-Molybdenum-Tungsten《铬钼钨合金钢压力容器板的标准规格》.pdf

ASTM A1017 A1017M-2017 Standard Specification for Pressure Vessel Plates Alloy Steel Chromium-Molybdenum-Tungsten《铬钼钨合金钢压力容器板的标准规格》.pdf

ASTM A1018 A1018M-2008 Standard Specification for Steel Sheet and Strip Heavy-Thickness Coils Hot-Rolled Carbon Commercial Drawing Structural High-Strength Low-Alloy High-Strength .pdf

ASTM A1018 A1018M-2008a Standard Specification for Steel Sheet and Strip Heavy-Thickness Coils Hot-Rolled Carbon Commercial Drawing Structural High-Strength Low-Alloy High-Strength.pdf

ASTM A1018 A1018M-2009 Standard Specification for Steel Sheet and Strip Heavy-Thickness Coils Hot-Rolled Carbon Commercial Drawing Structural High-Strength Low-Alloy High-Strength .pdf