1、UD0 621.882.6 DEUTSCHE NORMEN August 1971 DIN 2510 Bolted Connections with Reduced Lshank stud-bolts I Port 3 Schraubenverbindungen mit dbhnschaf t ; &hraubembol%en l!yDe L with lonu thread up to M 52 DM 2510 t. Detail y Centring for hole db3) Me K with short thread up to H 56 Dl3 2510 for M 64 DIB
2、2510 and upwards -26- =- - I other dimenaions and details as for Qpe L me glT with short thread and spacer point (only for uee with cap nute at both ends) up to H 56 DIN 2510 for M 64 DIN 2510 ana upwaras other dimensions and details as for Type L and K !Cyme 2 with lonu thread up to M 56 DIN 2510 f
3、or M 64 DIN 2510 and upwards 1 Md 3, e on page 3 For Explanations see DIN 2510 Part 1 Continued on pages 2 and 3 lleinverkauf der Normen durch Beuth Verlag GmbH, Berlin 3 und Kln 1 .79 Verir.-Nr. 010) DIN 2510 B1. 3 engl. PreisEr* Page 2 DIN 2510 Part 3 SW I, 10 “2 =3 IA other dimensions and details
4、 as for Type L and K ? 10 II 11 13 13 il 22 24 14 27 n a32 125 2 2.5 3 3 3.5 3.5 4 4 4.3 4.5 5 5 5.5 4 5 6 6 6 6 9 9 10 10 11 11 12 13 II 14 16 17 19 19 21 2323 24 25 26 ma 7 8 9 B IO 11 14 I4 14 1s 15 19 18 19 Designation of a stud-Bolt Pype L with thread d, = M 50 and nominal length 11 - 200 mm) i
5、n 24CrNo5 (code letter G 1): Stud-bolt L M 30 x 200 DIN 2510 - 24CrMo5 SW I, M 25 25 25 25 25 25 32 32 32 32 32 32 32 36 41 41 41 41 41 41 41 55 55 55 u 55 6 6 6 6 6 6 6 8 8 8 8 8 8 r-zddilII DIN 251 MMiM72x6 M80x6 MWx6 MlOx6 I M110x6 I (MlZxb I M125x6 I M140x8 I (MlSOxdl I M160x8 I (M170x8) I Ml8Ox
6、8 I I bl Iss195 11031112I in I 132 I142 I - I - I - I - I - I - I I I I I I A4 l A 6.3 I Bracketed sizes should be avoided where poesible. I), 2, and 3) see on page 3 DH 2510 Part 3 Page 3 -?i m according to DIN 267 Part 13 f only to special order. The designation in thie case reade, e.6.: Stud-bolt
7、 I, M 30 x 200 DIN 2510 - f - 24CrMos IJarar&ogi according to DIN 267 Part I3 Unless agreed to the contrary when ordering, the marking should be applied to the end face of the point “2. If stud-bolts of Types K, KU, 2 or ZU for M 64 DIN 2510 and upwards are required without hole &+, then the letter
8、O should be inserted in the designation, e.g.: Stud-bolt KO M 100 x 6 x 600 DIN 2510 - 24CrMo5 1 Nominal length 1, to be stated when ordering (eee also DIN 2510 Part 1) 2) Instead of the code number the code letter of the material may rlso be stated in the dadgnation. In such cnaee the designation reade, 0.g.: Stud-bolt L M 30 X 200 DIN 2510 - 0 3) Centring according to DIN 332 and detail Y only for etud-bolt. of type f.
