1、May 2017 English price group 12No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 77.140.70!%e_*“2666007www.din.deDIN
2、EN 10365Hot rolled steel channels, I and H sections Dimensions and masses;English version EN 10365:2017,English translation of DIN EN 10365:2017-05Warmgewalzter UProfilstahl, I und HTrger Mae und Masse;Englische Fassung EN 10365:2017,Englische bersetzung von DIN EN 10365:2017-05Profils en U en acier
3、s lamins chaud, poutrelles I et H Dimensions et masses;Version anglaise EN 10365:2017,Traduction anglaise de DIN EN 10365:2017-05www.beuth.deDocument comprises 35 pagesDTranslation by DIN-Sprachendienst.In case of doubt, the German-language original shall be considered authoritative.05.17 DIN EN 103
4、65:2017-05 2 A comma is used as the decimal marker. National foreword This document (EN 10365:2017) has been prepared by Technical Committee CEN/TC 103 “Structural steels other than reinforcements” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was DIN-Normenaus
5、schuss Eisen und Stahl (DIN Standards Committee Iron and Steel), Working Committee NA 021-00-21-06 UA “Hot-rolled sections”. EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10365 January 2017 ICS 77.140.70 English Version Hot rolled steel channels, I and H sections - Dimensions and masses Profi
6、ls en U en aciers lamins chaud, poutrelles I et H - Dimensions et masses Warmgewalzter U-Profilstahl, I- und H-Trger - Mae und Masse This European Standard was approved by CEN on 14 November 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the condition
7、s for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in
8、three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards
9、 bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia,
10、 Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means res
11、erved worldwide for CEN national Members. Ref. No. EN 10365:2017 EEN 10365:2017 (E) 2 Contents Page European foreword . 3 1 Scope 4 2 Normative references 4 3 Terms and definitions . 5 4 Designation 5 5 Dimensions and masses 5 6 Tolerances on dimensions, shape and mass . 7 7 Material . 7 Annex A (in
12、formative) Comparison of symbols used in this document with those in EN 1993-1-1 32 Bibliography . 33 DIN EN 10365:2017-05 EN 10365:2017 (E) 3 European foreword This document (EN 10365:2017) has been prepared by Technical Committee ECISS/TC 103 “Structural steels other than reinforcements”, the secr
13、etariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2017, and conflicting national standards shall be withdrawn at the latest by July 2017. Attention is drawn to
14、 the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This project was submitted to the Enquiry under reference prEN 16828. According to the CEN-CENELEC Internal Regulations, t
15、he national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latv
16、ia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 10365:2017-05 EN 10365:2017 (E) 4 1 Scope This European standard specifies the nominal dimensions and masses of the hot roll
17、ed steel channels, I and H sections. The following shapes are covered by this standard: Sections: Parallel flange I sections IPE; Wide flange beams HE; Extra wide flange beams HL and HLZ; Wide flange columns HD; Wide flange bearing piles HP and UBP; Universal beams UB; Universal columns UC; Taper fl
18、ange I sections IPN and J. Channels: Parallel flange channels UPE and PFC; Taper flange channels UPN, U and CH. These requirements do not apply to hot rolled steel channels, I and H sections from stainless steel. 2 Normative references The following documents, in whole or in part, are normatively re
19、ferenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10024, Hot rolled taper flange I sections - Tolerances on shape and
20、dimensions EN 10025-1, Hot rolled products of structural steels - Part 1: General technical delivery conditions EN 10025-2, Hot rolled products of structural steels - Part 2: Technical delivery conditions for non-alloy structural steels EN 10025-3, Hot rolled products of structural steels - Part 3:
21、Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels EN 10025-4, Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels EN 10025-5, Hot rolled products of struc
22、tural steels - Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance EN 10034, Structural steel I and H sections - Tolerances on shape and dimensions DIN EN 10365:2017-05 EN 10365:2017 (E) 5 EN 10079, Definition of steel products EN 10279, Hot rol
23、led steel channels - Tolerances on shape, dimensions and mass 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 10079 apply. 4 Designation A section shall be designated according to Tables 1 to 15. This form of designation shall be used in any enquiry a
24、nd order. 5 Dimensions and masses Hot rolled steel channels, I and H sections complying with this European Standard shall be manufactured with the specified dimensions given in the Table 1 to 15 and according to Figures 1 to 4 below. Radii of fillets and toes of shape profiles vary with individual m
25、anufacturers and therefore are not specified. The masses per unit length specified in Tables 1 to 15 were calculated on the basis of a density of 7850 kg/m3. Figure 1 IPE, HE, HL, HD, HP, UBP, UB and UC parallel flange sections DIN EN 10365:2017-05 EN 10365:2017 (E) 6 Figure 2 Taper flange I section
26、s IPN, J and extra wide flange beams HLZ Figure 3 Parallel flange channels UPE and PFC Figure 4 Taper flange channels UPN, U and CH DIN EN 10365:2017-05 EN 10365:2017 (E) 7 6 Tolerances on dimensions, shape and mass Tolerances on dimensions, shape and mass shall be as given in EN 10034 for I (parall
27、el flanges) and H sections. Tolerances on dimensions, shape and mass shall be as given in EN 10024 for taper flange I sections. Tolerances on dimensions, shape and mass shall be as given in EN 10279 for channels. Tolerances for shapes not included in the mentioned standards shall be as agreed upon b
28、etween the manufacturer and the purchaser. 7 Material Sections and channels shall preferably be made from steel of a grade as specified in EN 10025-1, EN 10025-2, EN 10025-3, EN 10025-4 and EN 10025-5. Other steel grades as specified in EN 10225, EN 10028-2 and EN 10273 may also be used for specific
29、 applications. The desired steel grade shall be specified at the time of ordering. DIN EN 10365:2017-05 EN 10365:2017 (E) 8 Table 1 Parallel flange I sections IPE Designation Dimensions G h b s t A kg/m mm mm mm mm cm2IPE AA 80 4,9 78,0 46,0 3,2 4,2 6,3 IPE A 80 5,0 78,0 46,0 3,3 4,2 6,4 IPE 80 6,0
30、80,0 46,0 3,8 5,2 7,6 IPE AA 100 6,7 97,6 55,0 3,6 4,5 8,6 IPE A 100 6,9 98,0 55,0 3,6 4,7 8,8 IPE 100 8,1 100,0 55,0 4,1 5,7 10,3 IPE AA 120 8,4 117,0 64,0 3,8 4,8 10,7 IPE A 120 8,7 117,6 64,0 3,8 5,1 11,0 IPE 120 10,4 120,0 64,0 4,4 6,3 13,2 IPE AA 140 10,1 136,6 73,0 3,8 5,2 12,8 IPE A 140 10,5
31、137,4 73,0 3,8 5,6 13,4 IPE 140 12,9 140,0 73,0 4,7 6,9 16,4 IPE AA 160 12,3 156,4 82,0 4,0 5,6 15,7 IPE A 160 12,7 157,0 82,0 4,0 5,9 16,2 IPE 160 15,8 160,0 82,0 5,0 7,4 20,1 IPE AA 180 14,9 176,4 91,0 4,3 6,2 19,0 IPE A 180 15,4 177,0 91,0 4,3 6,5 19,6 IPE 180 18,8 180,0 91,0 5,3 8,0 23,9 IPE O 1
32、80 21,3 182,0 92,0 6,0 9,0 27,1 IPE AA 200 18,0 196,4 100,0 4,5 6,7 22,9 IPE A 200 18,4 197,0 100,0 4,5 7,0 23,5 IPE 200 22,4 200,0 100,0 5,6 8,5 28,5 IPE O 200 25,1 202,0 102,0 6,2 9,5 32,0 IPE AA 220 21,2 216,4 110,0 4,7 7,4 27,0 IPE A 220 22,2 217,0 110,0 5,0 7,7 28,3 IPE 220 26,2 220,0 110,0 5,9
33、 9,2 33,4 IPE O 220 29,4 222,0 112,0 6,6 10,2 37,4 IPE AA 240 24,9 236,4 120,0 4,8 8,0 31,7 IPE A 240 26,2 237,0 120,0 5,2 8,3 33,3 IPE 240 30,7 240,0 120,0 6,2 9,8 39,1 IPE O 240 34,3 242,0 122,0 7,0 10,8 43,7 DIN EN 10365:2017-05 EN 10365:2017 (E) 9 Designation Dimensions G h b s t A kg/m mm mm mm
34、 mm cm2IPE A 270 30,7 267,0 135,0 5,5 8,7 39,2 IPE 270 36,1 270,0 135,0 6,6 10,2 45,9 IPE O 270 42,3 274,0 136,0 7,5 12,2 53,8 IPE A 300 36,5 297,0 150,0 6,1 9,2 46,5 IPE 300 42,2 300,0 150,0 7,1 10,7 53,8 IPE O 300 49,3 304,0 152,0 8,0 12,7 62,8 IPE A 330 43,0 327,0 160,0 6,5 10,0 54,7 IPE 330 49,1
35、 330,0 160,0 7,5 11,5 62,6 IPE O 330 57,0 334,0 162,0 8,5 13,5 72,6 IPE A 360 50,2 357,6 170,0 6,6 11,5 64,0 IPE 360 57,1 360,0 170,0 8,0 12,7 72,7 IPE O 360 66,0 364,0 172,0 9,2 14,7 84,1 IPE A 400 57,4 397,0 180,0 7,0 12,0 73,1 IPE 400 66,3 400,0 180,0 8,6 13,5 84,5 IPE O 400 75,7 404,0 182,0 9,7
36、15,5 96,4 IPE V 400 84,0 408,0 182,0 10,6 17,5 107,0 IPE A 450 67,2 447,0 190,0 7,6 13,1 85,6 IPE 450 77,6 450,0 190,0 9,4 14,6 98,8 IPE O 450 92,4 456,0 192,0 11,0 17,6 117,7 IPE V 450 107 460,0 194,0 12,4 19,6 132,0 IPE A 500 79,4 497,0 200,0 8,4 14,5 101,1 IPE 500 90,7 500,0 200,0 10,2 16,0 115,5
37、 IPE O 500 107 506,0 202,0 12,0 19,0 136,7 IPE V 500 129 514,0 204,0 14,2 23,0 164,1 IPE A 550 92,1 547,0 210,0 9,0 15,7 117,3 IPE 550 106 550,0 210,0 11,1 17,2 134,4 IPE O 550 123 556,0 212,0 12,7 20,2 156,1 IPE V 550 159 566,0 216,0 17,1 25,2 202,0 IPE A 600 108 597,0 220,0 9,8 17,5 137,0 IPE 600
38、122 600,0 220,0 12,0 19,0 156,0 IPE O 600 154 610,0 224,0 15,0 24,0 196,8 IPE V 600 184 618,0 228,0 18,0 28,0 233,8 DIN EN 10365:2017-05 EN 10365:2017 (E) 10 Designation Dimensions G h b s t A kg/m mm mm mm mm cm2IPE 750 134 134 750,0 264,0 12,0 15,5 170,6 IPE 750 147 147 753,0 265,0 13,2 17,0 187,5
39、 IPE 750 173 173 762,0 267,0 14,4 21,6 221,3 IPE 750 196 196 770,0 268,0 15,6 25,4 250,8 DIN EN 10365:2017-05 EN 10365:2017 (E) 11 Table 2 Wide flange beams HE Designation Dimensions G h b s t A kg/m mm mm mm mm cm2HE 100 AA 12,2 91,0 100,0 4,2 5,5 15,6 HE 100 A 16,7 96,0 100,0 5,0 8,0 21,2 HE 100 B
40、 20,4 100,0 100,0 6,0 10,0 26,0 HE 100 C 30,9 110,0 103,0 9,0 15,0 39,3 HE 100 M 41,8 120,0 106,0 12,0 20,0 53,2 HE 120 AA 14,6 109,0 120,0 4,2 5,5 18,6 HE 120 A 19,9 114,0 120,0 5,0 8,0 25,3 HE 120 B 26,7 120,0 120,0 6,5 11,0 34,0 HE 120 C 39,2 130,0 123,0 9,5 16,0 49,9 HE 120 M 52,1 140,0 126,0 12
41、,5 21,0 66,4 HE 140 AA 18,1 128,0 140,0 4,3 6,0 23,0 HE 140 A 24,7 133,0 140,0 5,5 8,5 31,4 HE 140 B 33,7 140,0 140,0 7,0 12,0 43,0 HE 140 C 48,2 150,0 143,0 10,0 17,0 61,5 HE 140 M 63,2 160,0 146,0 13,0 22,0 80,6 HE 160 AA 23,8 148,0 160,0 4,5 7,0 30,4 HE 160 A 30,4 152,0 160,0 6,0 9,0 38,8 HE 160
42、B 42,6 160,0 160,0 8,0 13,0 54,3 HE 160 C 59,2 170,0 163,0 11,0 18,0 75,4 HE 160 M 76,2 180,0 166,0 14,0 23,0 97,1 HE 180 AA 28,7 167,0 180,0 5,0 7,5 36,5 HE 180 A 35,5 171,0 180,0 6,0 9,5 45,3 HE 180 B 51,2 180,0 180,0 8,5 14,0 65,3 HE 180 C 69,8 190,0 183,0 11,5 19,0 89,0 HE 180 M 88,9 200,0 186,0
43、 14,5 24,0 113,3 HE 200 AA 34,6 186,0 200,0 5,5 8,0 44,1 HE 200 A 42,3 190,0 200,0 6,5 10,0 53,8 HE 200 B 61,3 200,0 200,0 9,0 15,0 78,1 HE 200 C 81,9 210,0 203,0 12,0 20,0 104,4 HE 200 M 103 220,0 206,0 15,0 25,0 131,3 HE 220 AA 40,4 205,0 220,0 6,0 8,5 51,5 DIN EN 10365:2017-05 EN 10365:2017 (E) 1
44、2 Designation Dimensions G h b s t A kg/m mm mm mm mm cm2HE 220 A 50,5 210,0 220,0 7,0 11,0 64,3 HE 220 B 71,5 220,0 220,0 9,5 16,0 91,0 HE 220 C 94,1 230,0 223,0 12,5 21,0 119,9 HE 220 M 117 240,0 226,0 15,5 26,0 149,4 DIN EN 10365:2017-05 EN 10365:2017 (E) 13 Designation Dimensions G h b s t A kg/
45、m mm mm mm mm cm2HE 240 AA 47,4 224,0 240,0 6,5 9,0 60,4 HE 240 A 60,3 230,0 240,0 7,5 12,0 76,8 HE 240 B 83,2 240,0 240,0 10,0 17,0 106,0 HE 240 C 119 255,0 244,0 14,0 24,5 152,2 HE 240 M 157 270,0 248,0 18,0 32,0 199,6 HE 260 AA 54,1 244,0 260,0 6,5 9,5 69,0 HE 260 A 68,2 250,0 260,0 7,5 12,5 86,8
46、 HE 260 B 93,0 260,0 260,0 10,0 17,5 118,4 HE 260 C 132 275,0 264,0 14,0 25,0 168,4 HE 260 M 172 290,0 268,0 18,0 32,5 219,6 HE 280 AA 61,2 264,0 280,0 7,0 10,0 78,0 HE 280 A 76,4 270,0 280,0 8,0 13,0 97,3 HE 280 B 103 280,0 280,0 10,5 18,0 131,4 HE 280 C 145 295,0 284,0 14,5 25,5 185,2 HE 280 M 189
47、 310,0 288,0 18,5 33,0 240,2 HE 300 AA 69,8 283,0 300,0 7,5 10,5 88,9 HE 300 A 88,3 290,0 300,0 8,5 14,0 112,5 HE 300 B 117 300,0 300,0 11,0 19,0 149,1 HE 300 C 177 320,0 305,0 16,0 29,0 225,1 HE 300 M 238 340,0 310,0 21,0 39,0 303,1 HE 320 AA 74,2 301,0 300,0 8,0 11,0 94,6 HE 320 A 97,6 310,0 300,0
48、 9,0 15,5 124,4 HE 320 B 127 320,0 300,0 11,5 20,5 161,3 HE 320 C 186 340,0 305,0 16,0 30,5 236,9 HE 320 M 245 359,0 309,0 21,0 40,0 312,0 HE 340 AA 78,9 320,0 300,0 8,5 11,5 100,5 HE 340 A 105 330,0 300,0 9,5 16,5 133,5 HE 340 B 134 340,0 300,0 12,0 21,5 170,9 HE 340 M 248 377,0 309,0 21,0 40,0 315
49、,8 HE 360 AA 83,7 339,0 300,0 9,0 12,0 106,6 HE 360 A 112 350,0 300,0 10,0 17,5 142,8 HE 360 B 142 360,0 300,0 12,5 22,5 180,6 HE 360 M 250 395,0 308,0 21,0 40,0 318,8 DIN EN 10365:2017-05 EN 10365:2017 (E) 14 Designation Dimensions G h b s t A kg/m mm mm mm mm cm2HE 400 AA 92,4 378,0 300,0 9,5 13,0 117,7 HE 400 A 125 390,0 300,0 11,0 19,0 159,0 HE 400 B 155 400,0 300,0 13,5 24,0 197,8 HE 400 M 256 432,0 307,0 21,0 40,0 325,8 HE 450
