1、September 2015 Translation by DIN-Sprachendienst.English price group 13No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).
2、ICS 91.140.70!%F0,“2351309www.din.deDDIN EN 14296Sanitary appliances Communal washing troughs;English version EN 14296:2015,English translation of DIN EN 14296:2015-09Sanitrausstattungsgegenstnde Reihenwaschanlagen;Englische Fassung EN 14296:2015,Englische bersetzung von DIN EN 14296:2015-09Appareil
3、s sanitaires Lavabos collectifs;Version anglaise EN 14296:2015,Traduction anglaise de DIN EN 14296:2015-09SupersedesDIN EN 14296:2005-08See start of applicationwww.beuth.deIn case of doubt, the German-language original shall be considered authoritative.Document comprises 25 pages 08.15 DIN EN 14296:
4、2015-09 2 A comma is used as the decimal marker. Start of application The start of application of this standard is 2015-09-01. It should be noted that, in Germany, CE conformity marking of construction products will be permitted once this standard has been listed in the Official Journal of the Europ
5、ean Union and/or the Bundesanzeiger (German Federal Gazette) and from the date given therein. For further information, users of this standard should refer to the websites of the European Commission or of the relevant building authority. The standard which this document replaces, DIN EN 14296:2005-08
6、, may be used in parallel with this standard during a specified transition period where such has been laid down in the Official Journal of the European Union and/or the Bundesanzeiger (German Federal Gazette). National foreword This document (EN 14296:2015) has been prepared by Technical Committee C
7、EN/TC 163 “Sanitary appliances” (Secretariat: UNI, Italy). The responsible German body involved in its preparation was the DIN-Normenausschuss Wasserwesen (DIN Standards Committee Water Practice), Working Committee NA 119-05-18-01 UA Waschtische, Sitzwasch-becken, Klosetts, Urinale. Amendments This
8、standard differs from DIN EN 14296:2005-08 as follows: a) in Clause 2 “Terms and definitions”, “3.3 product type” has been added; b) Clause 6 “Dangerous substances” has been added; c) Clause 7 “Marking” has been modified; d) the former Clause 7 “Evaluation of conformity” has been replaced by Clause
9、8 “Assessment and verification of constancy of performance AVCP”; e) Annex ZA has been brought in line with the Construction Products Regulation (Regulation (EU) No 305/2011). Previous editions DIN EN 14296: 2005-08 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 14296 July 2015 ICS 91.140.70 S
10、upersedes EN 14296:2005English Version Sanitary appliances - Communal washing troughs Appareils sanitaires - Lavabos collectifs Sanitrausstattungsgegenstnde - Reihenwaschanlagen This European Standard was approved by CEN on 28 May 2015. CEN members are bound to comply with the CEN/CENELEC Internal R
11、egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN m
12、ember. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions
13、. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Pola
14、nd, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation
15、in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14296:2015 EEN 14296:2015 (E) 2 Contents Page European foreword .3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Requirements .4 4.1 General 4 4.2 Cleanability .5 4.3 Load resistance5 4.4 Durabili
16、ty 5 5 Test methods 5 5.1 Cleanability .5 5.2 Determination of load resistance .5 5.2.1 General 5 5.2.2 Load evenly distributed on the rim 6 5.2.3 Localized load on the rim 7 5.2.4 Test on the bottom.8 6 Dangerous substances .9 7 Marking .9 8 Assessment and verification of constancy of performance A
17、VCP 10 8.1 General . 10 8.2 Type testing . 10 8.2.1 General . 10 8.2.2 Test samples, testing and compliance criteria 11 8.3 Factory production control (FPC) . 12 8.3.1 General . 12 8.3.2 Equipment . 12 8.3.3 Raw materials and components 12 8.3.4 Product testing and assessment 12 8.3.5 Non-complying
18、products . 12 8.3.6 Corrective action. 13 Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU Construction Products Regulation . 14 ZA.1 Scope and relevant characteristics 14 ZA.2 Procedure for assessment and verification of constancy of performance (AVCP) of
19、 communal washing troughs 15 ZA.2.1 System of AVCP 15 ZA.2.2 Declaration of performance (DoP) 15 ZA.2.2.1 General . 15 ZA.2.2.2 Content . 16 ZA.2.2.3 Examples of DoP . 16 ZA.3 CE marking and labelling . 21 Bibliography . 23 DINEN 14296:2015-09EN 14296:2015 (E) 3 European foreword This document (EN 1
20、4296:2015) has been prepared by Technical Committee CEN/TC 163 “Sanitary appliances”, the secretariat of which is held by UNI. This document supersedes EN 14296:2005. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement
21、, at the latest by January 2016, and conflicting national standards shall be withdrawn at the latest by April 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying a
22、ny or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of the EU Construction Products Regulation. For relationship with EU Construction Products Regulation, se
23、e informative Annex ZA, which is an integral part of this document. Since the latest edition of EN 14296, the most significant technical changes are the following: a) introduction of the term “product type”; b) introduction of the clause “Dangerous substances”; c) modification of the marking of prod
24、ucts; d) replacement of the clause “Evaluation of conformity” by “Assessment and verification of constancy of performance AVCP” and replacement of Annex ZA by a new one in accordance with provisions of Regulation 305/2011. According to the CEN/CENELEC Internal Regulations, the national standards org
25、anisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg
26、, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 14296:2015-09 EN 14296:2015 (E) 4 1 Scope This European Standard specifies requirements for the cleanability, load resistance and durability of communal wash
27、ing troughs used for domestic purposes. NOTE For the purposes of this document, the term “domestic purposes” includes use in factory changing-rooms, sportsclubs, accommodation for students, hospitals and similar buildings, except when special medical provisions are required. 2 Normative references T
28、he following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 695,
29、Kitchen sinks - Connecting dimensions 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 communal washing trough single bowl sanitary appliance at which more than one person can wash at the same time, which is designed to be installed with (a) p
30、ermanently open waste fitting(s) capable of accepting the flow from more than one tap and which can be installed standing alone (free standing (pedestal) or wall mounted 3.2 cleanability characteristics which allow surfaces intended to come into contact with water to be visibly smooth, non-absorbent
31、 and free from unacceptable internal corners, such that they can be kept visibly free from dirt and/or stains when subject to a regular maintenance routine, which may include, when appropriate, the specific instructions for use and care as specified by the manufacturer 3.3 product type construction
32、product with a set of representative performance levels or classes in relation to its Essential Characteristics, produced using a given combination of raw materials or other elements in a specific production process 4 Requirements 4.1 General The manufacturer shall supply instructions on installatio
33、n, use and care. The waste outlet hole shall comply with the dimensions as specified in EN 695, unless the manufacturer provides the waste fitting with the washing trough. DIN EN 14296:2015-09 EN 14296:2015 (E) 5 4.2 Cleanability When tested as described in 5.1, communal washing troughs shall have s
34、mooth and readily cleansed non-absorbent functional surfaces which are free from acute internal corners, i.e. surfaces intended to or likely to come into contact with water during use. Experience has shown that communal washing troughs manufactured from plastics, enamelled steel/cast iron, stainless
35、 steel, glazed ceramics, glass and anodized aluminium, designed and constructed without acute internal corners, satisfy these requirements. 4.3 Load resistance Communal washing troughs shall not crack, collapse or show permanent distortion which prevents water from draining through the waste hole wh
36、en tested as specified in 5.2.2 and 5.2.4. Communal washing troughs shall not crack, or collapse when tested as specified in 5.2.3. 4.4 Durability Communal washing troughs shall be manufactured from materials that will satisfy the requirements of 4.2 and 4.3. 5 Test methods 5.1 Cleanability Visually
37、 examine the functional surface of the communal washing trough using a suitable light source. Record the material of construction and any failure to comply with the requirements of 4.2. Imperfections that do not affect the functionality of the surface shall not constitute a failure. 5.2 Determinatio
38、n of load resistance 5.2.1 General Install the communal washing trough to be tested according to the manufacturers installation instructions. DINEN 14296:2015-09EN 14296:2015(E)6 5.2.2 Load evenly distributed on the rim Apply an evenly distributed load of 250,50+kg every 50 cm on the rim, as shown i
39、n Figures 1 a), 1 b), 1 c) and 1 d). Reinforced cloth bags filled with lead shot, iron shot or sand shall be used. The load shall remain in position for a minimum period of 1 h. a) Wall mounted trough, viewed from the side Dimensions in millimetres b) Wall mounted trough, viewed from above c) Free s
40、tanding trough, viewed from the side d) Free standing trough, viewed from above Key 1 one bag of 250,50+kg or two bags of 12,50,250+kg Figure 1 Installation for load test - Test on the rim Note any crack, collapse or permanent distortion preventing water from draining trough the waste hole. DINEN 14
41、296:2015-09EN 14296:2015 (E) 7 5.2.3 Localized load on the rim Apply a load of 751,50+kg in the middle of the rim, as shown in Figures 2 a), 2 b), 2 c) and 2 d). Reinforced cloth bags filled with lead shot, iron shot or sand shall be used. The load shall remain in position for a minimum period of 1
42、h. a) Wall mounted trough, viewed from the side b) Wall mounted trough, viewed from above c) Free standing trough, viewed from the side d) Free standing trough, viewed from above Key 1 three bags of 250,50+kg or six bags of 12,50,250+kg Figure 2 Installation for load test - Test on the rim Note any
43、crack, or collapse of the trough. DIN EN 14296:2015-09 EN 14296:2015 (E) 8 5.2.4 Test on the bottom Apply an evenly distributed load of 250,50+kg every 50 cm on the bottom, as shown in Figures 3 a), b), c) and d) with a minimum total loading of 75 kg. Reinforced cloth bags filled with lead shot, iro
44、n shot or sand shall be used. The load shall remain in position for a minimum period of 1 h. a) Wall mounted trough, viewed from the side Dimensions in millimetres b) Wall mounted trough - Viewed from above c) Free standing trough, viewed from the side d) Free standing trough, viewed from above Key
45、1 one bag of 250,50+kg or two bags of 12,50,250+kg Figure 3 Installation for load test - Test on the bottom DIN EN 14296:2015-09 EN 14296:2015 (E) 9 Note any crack, collapse or permanent distortion of the trough preventing water from draining through the waste hole. 6 Dangerous substances National r
46、egulations on dangerous substances may require verification and declaration on release, and sometimes content, when construction products covered by this standard are placed on those markets. In the absence of European harmonized test methods, verification and declaration on release/content should b
47、e done taking into account national provisions in the place of use. NOTE An informative database covering European and national provisions on dangerous substances is available at the Construction website on EUROPA. 7 Marking The intended use of communal washing troughs is personal hygiene in accorda
48、nce with the scope of this standard. NOTE The intended use is also mentioned in Annex ZA, Table ZA.1. The abbreviation “PH” for the intended use personal hygiene might be used for CE marking. A schematic drawing of the product may optionally follow the abbreviation for personal hygiene. EXAMPLE 1 Use of full text: Personal hygiene. EXAMPLE 2 Use of abbreviation: PH. For communal washing troughs a set of requirements to be tested (see 8.2.2) is defined. Due to this, a communal washing trough can be described with a designation code which inc
