1、February 2012 Translation by DIN-Sprachendienst.English price group 7No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).IC
2、S 55.100!$y“1866195www.din.deDDIN EN 16067Packaging Rigid plastic containers PET finish 26,7 (lead 9,00)English translation of DIN EN 16067:2012-02Verpackung Kunststoffbehltnisse PET-Verschlussmundstck 26,7 (Gewindesteigung 9,00)Englische bersetzung von DIN EN 16067:2012-02Emballage Rcipients en pla
3、stique rigide Bague PET 26,7 (pas 9,00)Traduction anglaise de DIN EN 16067:2012-02www.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be considered authoritative.9 01.12 DIN EN 16067:2012-02 2 A comma is used as the decimal marker. National foreword This standard
4、 has been prepared by Technical Committee CEN/TC 261 “Packaging” (Secretariat: AFNOR, France). The responsible German body involved in its preparation was the Normenausschuss Verpackungswesen (Packaging Standards Committee), Working Committee NA 115-02-09 AA Behltnisse aus Kunststoff. EUROPEAN STAND
5、ARD NORME EUROPENNE EUROPISCHE NORM EN 16067 November 2011 ICS 55.100 English Version Packaging - Rigid plastic containers - PET finish 26,7 (lead 9,00) This European Standard was approved by CEN on 29 October 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stip
6、ulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European
7、Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the
8、 national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Sw
9、itzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. N
10、o. EN 16067:2011: EEmballage - Rcipients en plastique rigide - Bague PET 26,7 (pas 9,00) Verpackung - Kunststoffbehltnisse - PET-Verschlussmundstck 26,7 (Gewindesteigung 9,00) EN 16067:2011 (E) 2 Contents Page Foreword 3Introduction .41 Scope 52 Dimensions .53 Requirements .5Bibliography 7DIN EN 160
11、67:2012-02 EN 16067:2011 (E) 3 Foreword This document (EN 16067:2011) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by
12、endorsement, at the latest by May 2012, and conflicting national standards shall be withdrawn at the latest by May 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identify
13、ing any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany
14、, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. DIN EN 16067:2012-02 EN 16067:2011 (E) 4 Introduction This European Standard is based on CE.T.I.E.
15、(International Technical Centre for Bottling and Packaging) data sheet GME 30.24 (2008) 1. Efficient packaging is of great importance for the distribution and the protection of goods. Insufficient or inappropriate packaging can lead to damage or wastage of the contents of the pack. DIN EN 16067:2012
16、-02 EN 16067:2011 (E) 5 1 Scope This European Standard specifies the dimensions of the 26,7 mm screw finish with three (3) thread starts and a 16,80 mm height for flat waters and non-carbonated beverages. This finish can be used for aseptic filling and filling with introduction of nitrogen. This fin
17、ish is designed to take a tamper evident plastic closure only. During first opening, the tamper evident band will separate from the closure shell and stay on a one way bottle neck or like bottles in the returnable market, the tamper evident band will tear but will remain connected to the closure she
18、ll. 2 Dimensions 2.1 The design and dimensions of the finish shall be as shown in Figure 1. NOTE Other versions exist with Z = 33 mm max. 2.2 Dimensions of the 3 thread starts 120 apart. 120 of full depth thread per lead R 6,25 thread lead-in R 6,25 thread run-out Lead: 9 mm (travel per turn) 2.3 Ge
19、neral tolerance for other radii: 0,13 mm 2.4 Weight on height 16,8 mm: 3,38 g (density = 1,335) 3 Requirements The following requirements apply: This finish is a top, side and inside seal finish. This finish shall be smooth and free of any defects that will contribute to leaks. Flash shall not excee
20、d 0,13 mm per side, and shall not be continuous. On the blown bottle, the control diameter C shall be free of any defects up to 4 mm down for the internal bore and across the sealing surface of the finish. Requirements for good closure application on finish: 0,13 mm max. out-of-parallel sealing surf
21、ace with neck support ledge is allowed; an offset or vertical mismatch of thread is not to exceed 0,10 mm at the mould seam. T dimension is not measured in the depressed area. Variations in E are to follow uniformly those of T. No overhang allowed at any point in 360 between F and G. A flash to 0,15
22、 mm maximum step is allowable on one side only. G does not exceed E. In case of usage for slightly carbonated (3 g/l max.) waters and beverages, the bottler shall check that closure is suitable for this usage. DIN EN 16067:2012-02 EN 16067:2011 (E) 6 Dimensions in millimetres Key 1 start thread 5 ab
23、ove parting line 2 radius center 6 thread lead-in 3 thread starts 120 apart 7 thread run-out 4 straight NOTE * = includes ovality. Figure 1 Design and dimensions of the finish DIN EN 16067:2012-02 EN 16067:2011 (E) 7 Bibliography 1 CE.T.I.E. data sheet GME 30.24 PET finish 26,7 (lead 9,00) 2008 C.E.T.I.E. : International Technical Centre for Bottling and related Packaging 112 114 rue La Botie 75008 Paris www.cetie.org DIN EN 16067:2012-02
