1、A-A-55434 9999574 0355447 b M I INCH POUND 1 A-A- 5 5 4 3 4 August 26, 1993 COMMERCIAL ITEM DESCRIPTION LIGHT, CHEMILUMINESCENT, 4 IN - 6 HR - B, C The General Services Administration has authorized the use of this commercial item description. Abstract. This description covers 6 hour 4 inch chemilum
2、inescent lights (commonly known as a light wand) used for a variety of lighting, marking, and identification purposes. Salient characteristics. 1. Color. The colors of the chemiluminescent lights described in this CID are green and orange. The color wand required shall be identified in the Part Iden
3、tification Number (PIN) paragraph of this CID. Beneficial comments, recommendations, additions, deletions clarifications, etc., and any data which may improve this document should be sent to: Commander, Space and Naval Warfare Command, ATTN: SPAWAR 003-114/031, Washington, DC 20363. AMSC N/A FSC 626
4、0 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Licensed by Information Handling ServicesA-A-5 54 34 2. Desisn. The chemiluminescent light shall be elongated having an overall length of 4 inches plus or minus 0.125 inches. The mid point diameter shall be no less t
5、han -500 inches and the wand shall have a flat base on one end. The diameter of the flat end shall not exceed -750 inches. The end opposite the flat base shall have a hole .188 inches nominal. Lightstickc shall have a tapered shape and shall be compatible with the following accessory items; Ground S
6、take (NSN 6260-01-230-8555), Handle, six (6) inch (NSN 6260-01-255-3345), and individually wrapped in an airtight wrapper, 3. Interior. The chemiluminescent lights specified in this Commercial Item Description shall produce a level of light intensity as specified in Table I for a specified length of
7、 time (6 hours). The chromaticity of the emitted light must also meet the requirements in Table I. 4. Material Safetv Data Sheet. Manufacturer shall provide evidence in the form of a Material Safety Data Sheet (MSDS) (Fed-Std-313) that the components shall not be highly toxic, toxic, corrosive or ir
8、ritant in terms of the definitions and tests in Code of Federal Regulations, Title 16, Part 1500 (Federal Hazardous Substances Act). 5. Test Criteria. Illuminance (Lumens per square meter) must meet or exceed the data presented in Table I below. After Ageing Test, illuminance must meet or exceed dat
9、a in Table II. light. following measured 10 minutes after activation at 24 degrees C: x = 0.5861 plus or minus 0.0172, y = 0.4156, plus or minus 0.0156. Activated by manually flexing the plastic tube, breaking the inner vial and shaking to combine components. Plastic tube shall not leak and vial wil
10、l not break when subjected to an external pressure equivalent to 30,000 feet at 75 degrees F in a vacuum chamber. Must withstand a free fall, while still in wrapper, from a height of 8.5 feet on a hard surface (concrete) without activating or leakage. 6. Test conditions. Emits orange color CIE chrom
11、aticity coordinate measurements must meet the a, Meter: Digital Photometer, TEKTRONIX, Model 516, Sensor Probe 56501. All meters traceable to NIST. b. Wand to Tektronix J16 Meter Distance: 1.50 5 0.02 inches. Wand to Luminance Meter: 12 inches c. Temperature stabilization: Wands, while still in seal
12、ed foil I wrappers, will be placed in a water bath at test temperature for a minimum of one (1) hour before activation. I d. activation. Remove wand from sealed foil wrapper immediately before Light wand shall be handled by cap end during testing. 2 Licensed by Information Handling ServicesA-A-55Li3
13、4 9999974 0355449 4b3 = A-A-554 34 e. Activation method: Bend; agitate for ten seconds. f. Wands shall be agitated for-ten (10) seconds before each a reading. g. Wands kept under cover or in darkness; may be exposed to light during movement to and from light meter. h. All meter readings made in dark
14、ness. i. Remove wand from foil wrapper immediately before activation. j. Activation method: bend, agitate (hand shake) for ten (10) seconds. k. Wands, will be returned to their water bath at test temperature immediately after each meter reading. 1. During Light Intensity vs Time Test, wands shall be
15、 agitated for ten (10) seconds prior to every meter reading. Readings shall be taken within 5 seconds following agitation with the wand held in a vertical position, flat end up, using Wand Test Fixture Holder identified in drawing number DGSCV-91-03, item number 1, CAGE No. 13873. Meter held perpend
16、icular to longitudinal axis of wand with lens aimed at fluid column width midpoint and 2.250 inches plus or minus .O39 inches from flat end. Reflected light will be prevented from entering the meter lens. The cylindrical volume with an axis along the line of sight (meter to wand) 1.500 inches plus o
17、r minus .Oll inches long and a radius of 11.811 inches, plus or minus .394 inches will be void of all objects during intensity measurements except for support structures covered with a flat black color. m. Meter kept at 75 degrees F for all tests. n. Temperature tolerances: minus 2 degrees F. o. Hol
18、der, wand test fixture in accordance with DGSC drawing, DGSCV-91-03, Part Number 3. (Enclosure 1) p. Chemiluminescent lights shall be held in a vertical position with cap end down when light output measurement is made. q. Ageing Test - test conditions to be added at a future revision date. Contracto
19、r certification. The contractor shall certify, and maintain objective quality evidence that the product offered to the Government meets the salient characteristics of this description and that the product conforms to the producers own drawings, standards specifications, and quality assurance practic
20、es and is the same produced as the manufacturers current product offered by the contractor in the commercial marketplace for at least one year preceding the solicitation. require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of
21、 The Government reserves the right to - the contract. O Licensed by Information Handling Servicesm Oe O0 O0 m O0 o4 O0 W (uw ON O0 . d wm ou) O0 w Pa3 da3 o4 m em Wm ow . m . . O . W O0 O0 . W ln4 ow O0 . In u)o OP O0 . O ow O0 m de dN o4 ee Oe O0 eo om O0 Oe Inm . . . Cr vi a o ww En H (Y w +I h -
22、O e O O - A 4 v e e O W m O O - N In O O u W viW Wp: WO PCW xn nd (Y +I u m sa 143 La +IW o VIW W p:O wn (Y u vio ww Wn PI: o4 W n +I mu I- vi 21 na ww U 3s nN 2 O X In - m e - P; X m P In O O H a ri B 3 a W H O H 5 L vi W H u E g H n s W cr: * H vi Hvi zw HE! u p:Z WH H n w* % Y n =o $2 WN m W W O
23、O . m QI O O . P O H W u E H QI e O O h 4 v m In O . N e 4 O . m In 4 . Wh m m O O . A 4 v W m O . w m (u In N N O . m e N . 4 m “e WH61 - 4 Y d I- O . a al a a st Q, a O 4 m 4 m al Pl a H n m W W O O . In O O W m e O O N O . - W W W O W 4 (u . 4 e I- Err N m Erc In r- P; O GI O L) - II -A II *o k Y
24、wwz oOi;r(zf3w s 4 Licensed by Information Handling Services.-II- I Ya+ I n c c 5 ENCLOSURE 1 Licensed by Information Handling ServicesA-A-55 434 9999974 0155452 T5b A-A-5 54 34 Metric products. Products manufactured to metric dimensions will O be considered on an equal basis with those manufactured
25、 using inch-pound units, provided they fall within specified tolerances using conversion tables contained in the latest revision of Federal Standard No. 376, and all other requirements of this Commercial Item Description are met. If a product is manufactured to metric dimensions and those dimensions
26、 exceed the tolerances specified in the inch-pound units, a request should be made to the contracting officer to determine if the product is acceptable. accepting or rejecting the product. Resulatorv requirements. recovered materials in accordance with Public Law 94-580 to the maximum extent practic
27、able. The contracting officer has the option of The offeror/contractor is encouraged to use Qualitv assurance. Foil leakaqe. Samples will be tested for foil leakage by application of 6 psi air pressure into the inside of the foil wrap while submerged under water. from any portion of the foil, except
28、 where the foil has been penetrated by the air supply shall be classified as an airtight foil failure. A steady stream of air bubbles coming Shelf life. Each chemiluminescent light shall have a minimum of 42 months life remaining at the time of delivery to the Government and must have been manufactu
29、red within 6 months of the date of delivery to the Government. 0 Fluid Level. The vertical fluid level, when measured from the exterior of the flat base shall be no less than 1.609 Inches. Preservation, packaqinq, p ackinq, labelina, and markinq The preservation, packaging, packing, labeling, and ma
30、rking shall be as specified in the contract or order. Foil wrapping and all other packaging shall be marked with manufacturers lot number and expiration date. I I I I Foil wrapping shall be color coded and contain operating CID based Part Identification Number. The following Part Identification Numb
31、ering procedure is for Government purposes and does not constitute a requirement for the contractor. instructions. i i A-A-XXXXX-X I II COLOR B=GREEN CID NUMBER C=ORANGE 6 Licensed by Information Handling ServicesA-A-55434 9 9999974 0355453 992 9 A-A-554 34 Notes. Orderinq data. following: a. Title,
32、 number, part identification number with applicable Acquisitions documents must specify the color code letter, and date of this document. b. Material Safety Data Sheet (MSDS) shall be provided to Contracting Officer prior to award (FAR 52.233-3 and MSDS Page 2) Contracting Officer may request proof
33、of certification of commercial item prior to first contract delivery (See Contractor Certification, Page 3). c. MILITARY INTEREST: CIVIL AGENCY COORDINATING ACTIVITY: MILITARY COORDINATING ACTIVITY: Custodians Navy-EC Air Force-99 Reviewinq Activities DLA-GS User Activities Navy-YD GSA-FSS PREPARING ACTIVITY: Navy-EC AGENT: DLA-GS PROJECT NO. 6260-1029 FSC 6260 7 1 Licensed by Information Handling Services
