1、 INCH POUNDMIL-DTL-32185 January 12, 2005 DETAIL SPECIFICATION TROUSERS, COLD WEATHER, UNIVERSAL CAMOUFLAGE This specification is approved for use by all departments and agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers nylon, three layer laminated waterproof and m
2、oisture vapor permeable trousers used as a component of the Extended Cold Weather Clothing System (ECWCS). 1.2 Classification. The trousers will be of one type in the following sizes as specified (see 6.2). Size X-Short Short Regular LongX-Small X X X X Small X Medium X X X X Large - X-Large - - X X
3、 Comments, suggestions, or questions on this document should be addressed to: Defense Supply Center Philadelphia, Clothing and Textiles Directorate, Attn: DSCP-COCT (Bldg 6), 700 Robbins Ave., Philadelphia, PA 19111-5092 or emailed to Colleen.M.Robinsondla.mil. Since contact information can change,
4、you may want to verify the currency of this address information using the ASSIST Online database at http:/assist.daps.dla.mil AMSC N/A FSC 8415 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited Provided by IHSNot for ResaleNo reproduction or networking permitted withou
5、t license from IHS-,-,-MIL-DTL-32185 22. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or
6、as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications
7、, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the solicitation or contract. FEDERAL SPECIFICATIONS A-A-50083 - Bag, Plastic,
8、 Folded Garment A-A-50199 - Thread, Polyester Core, Cotton or Polyester-Covered A-A-55126 - Fastener, Tapes, Hook and Loop, Synthetic A-A-55634 - Fasteners, Slide, Interlocking DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-DTL-31011 - Cloth, Waterproof and Moisture Vapor permeable MIL-C-43701 - Cord, Ela
9、stic, Nylon MIL-F-10884 - Fasteners, Snap MIL-DTL-32075 - Label: For Clothing, Equipage, and Tentage (General Use) MIL-PRF-5038 - Tape, Textile and Webbing, Textile, Reinforcing Nylon MIL-T-3530 - Thread and Twine: Mildew Resistant or Water Repellent Treated MIL-DTL-32072 Thread, Polyester DEPARTMEN
10、T OF DEFENSE STANDARDS MILITARY MIL-STD-129 - Marking for Shipment and Storage(Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094
11、.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32185 32.3 Non-Government publications. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are th
12、ose cited in the solicitation or contract. ASTM INTERNATIONAL D 1974-1998 - Boxes, Shipping, Fiberboard ASTM D2582 - Puncture Propagation Tear ASTM D3776 - Mass Per Unit Area (Weight) of Woven Fabrics ASTM D3884 - Abrasion Resistance of Textile Fabrics D 3951 - Standard Practice for Commercial Packa
13、ging ASTM D5034 - Breaking Strength of Textile Fabrics D5118 - Practice for Fabrication of Fiberboard Shipping Boxes ASTM D6193 - Standard Practice for Stitches and Seams (Applications for copies are available from www.astm.org or American Society for Testing and Materials, 100 Barr Harbor Drive, We
14、st Conshohocken, PA 19428.) AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS AATCC-8 - Colorfastness to Crocking: AATCC Crockmeter Method AATCC-15 - Colorfastness to Perspiration AATCC-16 - Colorfastness to Light AATCC-22 - Water Repellency: Spray Test AATCC-61 - Colorfastness to Laundering, H
15、ome and Commercial: Accelerated AATCC-96 - Dimensional Changes in Commercial Laundering of Woven and Knitted Fabrics Except Wool AATCC-118 - Oil Repellency: Hydrocarbon Resistance Test AATCC-119 - Resistance to Frosting AATCC-135 - Dimensional Changes in Automatic Home Laundering of Woven and Knit F
16、abrics Procedure 1 - Gray Scale for Color Change (Copies of these documents are available from http:/www.aatcc.org or American Association of Textile Chemists and Colorists (AATCC), P.O. Box 12215, Triangle Park, NC 27709-2215.) AMERICAN NATIONAL STANDARDS INSTITUTE ANSI/ASQC Z1.4 Sampling Procedure
17、s and Tables For Inspection By Attributes Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32185 4(For all inquires please contact the American National Standards Institute, 25 West 43rdStreet, 4thFloor, New York, NY 10036). Website address ht
18、tp:/www.ansi.org TECHNICAL ASSOCIATION OF THE PULP AND PAPER INDUSTRY (TAPPI) (Applications for copies of referenced documents should be addressed to TAPPI Press, Technology Park/Atlanta, P.O. Box 105113, Atlanta, GA 30348-5113.) (Non-Government standards and other publications are normally availabl
19、e from the organizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this d
20、ocument takes precedence. Nothing in this document however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified (see 6.2), a sample shall be subjected to first article inspection in accordance with 4.2. 3.2 Guide
21、 samples. Samples, when furnished, are solely for guidance and information to the contractor (see 6.4). Variations from the specification may appear in the sample in which case this specification shall govern. 3.3 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or
22、environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.3.1 Base cloth. The base cloth for the trousers shall be made from w
23、aterproof and moisture vapor permeable cloth conforming to MIL-DTL-31011, Type III, Class 4. The color of the face side of the base cloth shall be Universal Camouflage. The color of the back side of the base cloth shall be Foliage Green 504. 3.3.1.1 Cloth, reinforcement . The cloth for use as knee p
24、atches, seat patches, cargo pockets, and cargo pocket flaps must be camouflage printed, water repellent treated and must resist fraying. The requirements for the cloth, reinforcement are as follows: Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL
25、-DTL-32185 5TABLE I. Cloth reinforcement requirementsCharacteristics Requirement Weight - 6.0 oz/sq. yd Max Breaking strength: Warp - 200 lbs.(min) Fill - 155 lbs.(min) Colorfastness to: Crocking - Dry and wet: 3.5 min. Laundering - Equal to or better than “3-4” rating on AATCC Gray Scale for Color
26、Change Light - Equal to or better than “3-4“ rating on AATCC Gray Scale For Color Change Perspiration Alkaline/Acid - Desert Sand 500 Good - Urban Gray 501 Good - Foliage Green 502 -Good Spray rating: Initial - 100, 100, 90 min. After 1 Laundering - 90, 90, 80 min. Stiffness (cm) - Warp 11.0 max Fil
27、l - 11.0 max. Puncture Propagation Tear - Warp 7.0 kgf min. - Filling 6.0 kgf min. Resistance to Organic liquid - No wetting by N-Tetradecane Resistance to Frosting - Equal or better than the standard sample The test specimen shall show no evidence of an appreciable change in color. Appreciable chan
28、ge in color means a change that is immediately noticeable on comparison of the test specimen with the original unexposed sample. If closer inspection or a change of angle of light is required to make apparent a slight change of color, the change is not considered appreciable. Dimensional Stability:
29、Warp - 4.0% (max) Fill - 4.0% (max) Abrasion Resistance - 800 cycles (min) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32185 6Infrared Spectral Reflectance Requirements Reflectance Values (Percent) Wavelengths Desert Sand 500 Urban Gray 5
30、01 Foliage Green 502Nanometers (nm) Min Max Min Max Min Max 600 28 42 12 26 8 18 620 30 44 14 26 8 18640 34 50 14 28 8 20 660 38 59 14 30 10 26680 44 63 18 34 10 26 700 46 69 24 38 12 28720 48 71 26 42 16 30 740 48 76 30 46 16 30760 50 80 32 48 18 32 780 54 80 34 48 18 34800 54 80 34 50 20 36 820 54
31、 80 36 54 22 38840 56 82 38 54 24 40 860 56 82 40 56 26 423.3.1.2 Cloth, three-layer knit. The material used for the leg insert shall be a three layer-knit, Foliage Green 504. The cloth shall conform to the following physical characteristics when tested in accordance with paragraph 4.5. TABLE II. Ph
32、ysical characteristics Characteristics Requirement Weight, oz/sq. yd. - 4.0 + 0.4 Stiffness, cm - 8.0 Max Hydrostatic Resistance, psi Initial Taffata Restraint - 220 Min. After deet - 120 Min. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3
33、2185 7TABLE II. Physical characteristics Characteristics Requirement Puncture Propagation Tear, kgf Warp - - 3.5 Min. Fill - 3.5 Min. Water permeability Initial - No leakage After Synthetic Perspiration - No leakage Moisture Vapor Transmission Rate (g/sq. m/24 hours): Procedure B - Initial - 600 Min
34、. Procedure BW - Initial - 5000 Min. Physical surface appearance after laundering - No changes after 20 launderings 3.3.2 Seam sealing tape. The tape for covering and sealing all designated seams and stitching shall be cut in 1 1/16 inch wide strips from material that is compatible with the back sid
35、e of the cloth specified in MIL-DTL-31011. The color shall be Foliage Green 504. 3.3.3 Tape, nylon. The tape for suspender loops shall be 1/2 inch flat nylon tape, Foliage Green 504, conforming to type III of MIL-PRF-5038. 3.3.4 Drawcord, elastic. The trouser drawcord shall be 3/16 inch diameter nyl
36、on elastic, Foliage Green 504, conforming to type II of MIL-C-43701. All ends shall be heat seared and knotted. 3.3.5 Fastener tape, hook and loop. The nylon fastener tapes shall be Foliage Green 504 conforming to type II, class 1 of A-A-55126 and in the widths specified in table II. 3.3.6 Fastener,
37、 slide, interlocking. All slide fasteners shall conform to A-A-55634, lengths shall be as specified, and the color shall be Foliage Green 504. Each slide fastener slider shall be equipped with a thong, Foliage Green 504. 3.3.7 Barrel lock. The barrel locks for the ends of the drawcords shall be Foli
38、age Green 504, ITW Nexus Barreloc or equivalent. 3.3.8 Fastener, snap. The stud and post parts of the snap fastener shall be Foliage Green 504, style 2A, finish 2 male and female complete, consisting of stud and eyelet Provided by IHSNot for ResaleNo reproduction or networking permitted without lice
39、nse from IHS-,-,-MIL-DTL-32185 8size 1 or 2 with button size 1 or 2 and socket conforming to MIL-F-10884, except an uncapped button may be used in areas where the surface will be concealed by a layer of base cloth. 3.3.9 Thread. The thread for all seaming and stitching shall be polyester, size B, 2
40、or 3 ply, conforming to type I, class 1, subclass B of MIL-DTL-32072. As an alternate, size 40, 2 or 3 ply polyester core thread conforming to A-A-50199 may be used. All thread shall be water-repellent treated as specified in MIL-T-3530. The thread color shall be Foliage Green 504. 3.3.10 Labels. Ea
41、ch trouser shall have a class l identification label, class 2 size label, and a class 3 instruction label, or a class 14 combination size, identification and instruction label conforming to type VI of MIL-DTL-32075. The label color shall be Foliage Green 504. The labels shall show fastness to launde
42、ring. 3.3.10.1 Identification label. The identification labels shall read “TROUSERS, COLD WEATHER, UNIVERSAL CAMOUFLAGE”. 3.3.10.2 Size label. The size label shall be as follows: X-Small X-Short Small X-ShortInseam: Up to 26-1/2 in. Inseam: Up to 26-1/2 in. Waist: Up to 27 in. Waist: 27 to 31 in. St
43、ock No: 8415-01-526-9039 Stock No: 8415-01-526-9046 NATO Size: 6067/5869 NATO Size: 6067/6979 Medium X-Short X-Small ShortInseam: Up to 26-1/2 in. Inseam: 26-1/2 to 29-1/2 in. Waist: 31 to 35 in. Waist: 27 to 31 in. Stock No: 8415-01-526-9059 Stock No: 8415-01-526-9044 NATO Size: 6067/7989 NATO Size
44、: 6775/5869 Small Short Medium ShortInseam: 26-1/2 to 29-1/2 in. Inseam: 26-1/2 to 29-1/2 in. Waist: 27 to 31 in. Waist: 31 to 35 in. Stock No: 8415-01-526-9050 Stock No: 8415-01-526-9060 NATO Size: 6775/6979 NATO Size: 6775/7989 Large Short Inseam: 26-1/2 to 29-1/2 in. Waist: 35 to 39 in. Stock No:
45、 8415-01-526-9064 NATO Size: 6775/8999 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32185 9X-Small Regular Small RegularInseam: 29-1/2 to 32-1/2 in. Inseam: 29-1/2 to 32-1/2 in. Waist: Up to 27 in. Waist: 27 to 31 in. Stock No: 8415-01-526
46、-9043 Stock No: 8415-01-526-9053 NATO Size: 7583/5869 NATO Size: 7583/6979 Medium Regular Large RegularInseam: 29-1/2 to 32-1/2 in. Inseam: 29-1/2 to 32-l/2 in. Waist: 31 to 35 in. Waist: 35 to 39 in. Stock No: 8415-01-526-9062 Stock No: 8415-01-526-9069 NATO Size: 7583/7989 NATO Size: 7583/8999 X-L
47、arge Regular X-Small LongInseam: 29-1/2 to 32-1/2 in. Inseam: 32-1/2 to 35-1/2 in. Waist: Over 39 in. Waist: Up to 27 in. Stock No: 8415-01-526-9072 Stock No: 8415-01-526-9048 NATO Size: 7583/9909 NATO Size: 8390/5689 Small Long Medium LongInseam: 32-1/2 to 35-1/2 in. Inseam: 32-1/2 to 35-1/2 in. Wa
48、ist: 27 to 31 in. Waist: 31 to 35 in. Stock No: 8415-01-526-9054 Stock No: 8415-01-526-9065 NATO Size: 8390/6979 NATO Size: 8390/7989 Large Long X-Large LongInseam: 32-1/2 to 35-1/2 in. Inseam: 32-1/2 to 35-1/2 in. Waist: 35 to 39 in. Waist: Over 39 in. Stock No: 8415-01-526-9068 Stock No: 8415-01-526-9070 NATO Size: 8390/8999 NATO Size: 8390/9909 3.3.10.3 Combination identification/size label. A combination identification/size label conforming to type VI, class 4 of MIL-DTL-32075 may be used. 3.3.10.4 Care instruction label. The care instruction label shall be as f
