1、 INCH-POUNDMS27234C 14 May 2007 SUPERSEDING MS27234B 22 September 2000 DETAIL SPECIFICATION SHEET ELBOW TUBE, 90 This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this spec
2、ification sheet and MIL-DTL-5070. FIGURE 1. Elbow dimensions and configuration. AMSC N/A Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-FSC 4730 MS27234C 2 Dash number A .015 (0.38 inches (mm) B +.031 (0.20) -.000 inches (mm) C Dia (see note 4.005 (
3、0.13) inches (mm)D Rad .060 (1.52) inches (mm) T tube wall thickness inches (mm) X (see note 5)inches (mm)-4 .531 (13.49) .245 (6.22) .375 (9.53) .035 (.89) .010 (.25) -5 .594 (15.09) .307 (7.80) .438 (11.13) .012 (.30) -6 .370 (9.40) .049 (1.24) .014 (.36) -8 .656 (16.66) .495 (12.57).500 (12.70) .
4、016 (.41) -10 .781 (19.84) .156 (3.96).620 (15.75).625 (15.88) .018 (.46) -12 1.094 (27.79) .745 (18.92).844 (21.44) .020 (.51) -16 1.219 (30.96) .995 (25.27).969 (24.61) .022 (.56) -20 1.438 (36.53) 1.245 (31.62)1.188 (30.18) .065 (1.65) .024 (.61) -24 1.625 (41.28) 1.495 (37.97)1.375 (34.93) .026
5、66) -32 2.000 (50.80) 1.995 (50.67)1.750 (44.45) .083 (2.11) .028 (.71) -40 2.312 (58.72) 2.370 (60.20)2.062 (52.37) -48 2.562 (65.07) .250 (6.35)2.995 (76.07)2.312 (58.72) .095 (2.41) .030 (.76) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless ot
6、herwise specified, break all corners, radius .010/.005 inch (.25/.01 mm). 4. Ovality at bend shall not exceed 5% of tubing outside diameter. 5. Face of tube must be perpendicular to centerline of the tube within X total indicator reading. 6. Break all sharp edges and remove all burrs and slivers. FI
7、GURE 1. Elbow dimensions and configuration - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27234C 3 REQUIREMENTS Dimensions and configurations: The design, construction, and physical dimensions shall be in accordance with MIL-DTL-5070
8、and figure 1 in case of conflict between this drawing and MIL-DTL-5070, this drawing shall govern. Intended use. This part is a component of MS27223 and MS27227. As part of an assembly this part is used on MS27224 and MS27228 hose to tube adapters. This item shall not be procured for stocking purpos
9、es. Materials: Materials shall be in accordance with MIL-DTL-5070. Finish: Finish shall be in accordance with MIL-DTL-5070. Platings are applied after heat treats. Color identification: Color identification shall be in accordance with MIL-DTL-5070. Part or Identifying Number (PIN) example: MS 27234
10、4 CZMaterial/finish code, see table I Dash number on figure 1 Specification number MS prefix TABLE I. Code for material and finish. Code Dash size Material/finish CC -4 through -6 Carbon Steel - cadmium plating CZ -4 through -6 Carbon steel - zinc plating SS -4 through -6 Corrosion resistant steel
11、 N/A AA -8 through -48 Aluminum - anodic coating TA -4 through -48 Titanium - anodized or fluoride phosphated. Identification of product. The PIN and the manufacturers Commercial and Government Entity (CAGE) code or trademark shall be permanently marked on the assembly, see figure 1, or on a remova
12、ble tag securely attached to the assembly. Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue, due to the extent of the changes. Referenced documents. In addition to MIL-DTL-5070, this document references the following
13、 MS27223 MS27224 MS27227 MS27228 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27234C 4 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AT DLA - CC Navy - AS Air Force - 99 (Project 4730-2005-052) DLA - CC Review activities: Army - AV
14、 Navy - MC, SA Air Force - 11, 70, 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
