1、 MS27238B INCH-POUND14 May 2007 SUPERSEDING MS27238A 22 September 2000 DETAIL SPECIFICATION SHEET WIRE, NUT RETAINING, DESIGNED FOR ADAPTER, HOSE TO TUBE, REUSABLE, HYDRAULIC, FUEL AND OIL LINES This specification is approved for use by all Departments and Agencies of the Department of Defense. The
2、requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-5070. Dash number A .015 (0.38) inch (mm) B inch (mm) C inch (mm) -4 1.203 (30.56).072 (1.83).067 (1.70).036 (.91) .016 (.41) -5 1.438 (36.53) .080 (2.03)-6 1.625 (41.28) .076 (1.93).040 (1.
3、02).020 (.51) -8 2.031 (51.59) .095 (2.41)-10 2.391 (60.73) .091 (2.31).047 (1.19).027 (.69) -12 2.938 (74.63)-16 3.703 (94.06)-20 4.688 (119.08)-24 5.469 (138.91)-32 7.453 (189.31).125 (3.18).121 (3.07).060 (1.52).040 (1.02)FIGURE 1. Wire dimensions and configuration. AMSC N/A Provided by IHSNot fo
4、r ResaleNo reproduction or networking permitted without license from IHS-,-,-FSC 4730 MS27238B 2 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Wire shall be straight within .020 inch (0.51 mm) total indicator reading. 4. Unless otherwise specified, maxi
5、mum surface roughness shall be 125 in Rain accordance with ASME B46.1. 5. Wire shall be free from scale, burrs, and slivers. FIGURE 1. Wire dimensions and configuration - Continued. REQUIREMENTS: Dimensions and configurations: The design, construction, and physical dimensions shall be in accordance
6、with MIL-DTL-5070 and figure 1 in case of conflict between this drawing and MIL-DTL-5070, this drawing shall govern. Intended use. This wire is to be used with MS27223 and MS27225. This item shall not be procured for stocking purposes. Materials: Materials shall be in accordance with MIL-DTL-5070. F
7、inish: Finish in accordance with MIL-DTL-5070. Color identification: Color identification shall be in accordance with MIL-DTL-5070. Part or Identifying Number (PIN) example: MS 27238 -24 CZMaterial/finish designator, see table I Dash number on figure 1 Specification number MS prefix TABLE I. Code fo
8、r material and finish. Code Dash size Material/finish CC -4 through -6 Carbon Steel - cadmium plating CZ -4 through -6 Carbon steel - zinc plating SS -4 through -6 Corrosion resistant steel - N/A AA -8 through -32 Aluminum - anodic coating TA -4 through -32 Titanium - anodized or fluoride phosphated
9、. To the users of this document, it is recommended that the use of carbon steel material with cadmium plating be used only when the other materials and finishes specified in this document cannot meet performance requirements. Provided by IHSNot for ResaleNo reproduction or networking permitted witho
10、ut license from IHS-,-,-MS27238B 3 Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue, due to the extent of the changes. Referenced documents. In addition to MIL-DTL-5070, this document references the following: MS2722
11、3 MS27225 ASME B46.1 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AT DLA - CC Navy - AS Air Force - 99 (Project 4730-2005-056) DLA - CC Review activities: Army - AV Navy - MC, SA Air Force - 11, 70, 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
