1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update to reflect latest changes in format and requirements. Editorial changes throughout. -les 04-11-09 Raymond Monnin THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED. REV SHET REV A A A SHEET 16 17 18 REV STATUS REV A A A A A A A A A
2、A A A A A OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 12 13 14 15 PMIC N/A PREPARED BY Thanh V. Nguyen DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Thanh V. Nguyen COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Mo
3、nica L. Poelking MICROCIRCUIT, DIGITAL, ECL, 4-STAGE COUNTER/SHIFT REGISTER, AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 93-01-26 MONOLITHIC SILICON AMSC N/A REVISION LEVEL A SIZE A CAGE CODE 67268 5962-92306 SHEET 1 OF 18 DSCC FORM 2233 APR 97 5962-E427-04 Provided by IHSNot for
4、 ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92306 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class l
5、evels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflecte
6、d in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 92306 01 M X A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Dev
7、ice classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a
8、non-RHA device. 1.2.2 Device type. The device type identifies the circuit function as follows: Device type Generic number Circuit function 01 100336 4-stage counter/shift register 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as
9、 follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outlines. The case o
10、utlines are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X GDIP5-T24 or CDIP6-T24 24 dual-in-line Y See figure 1 24 quad-flat 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535
11、, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92306 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maxi
12、mum ratings. 1/ Negative supply voltage range (VEE) -7.0 V dc to +0.5 V dc DC input voltage range (VIN) . VEEto +0.5 V dc Maximum dc output current (IOUT) -50 mA Storage temperature range -65C to +150C Lead temperature (soldering, 10 seconds) +300C Junction temperature (TJ) +175C Maximum power dissi
13、pation (PD) . 1280 mW Thermal resistance, junction-to-case (JC): Case X See MIL-STD-1835 Case Y 28 C/W 1.4 Recommended operating conditions. Negative supply voltage range (VEE) -5.7 V dc minimum to -4.2 V dc maximum High level input voltage range (VIH) -1.165 V dc minimum to -0.870 V dc maximum Low
14、level input voltage range (VIL) . -1.830 V dc minimum to -1.475 V dc maximum Case operating temperature range (TC) . -55C to +125C Minimum setup time, D3to CP (ts) 1.4 ns Minimum hold time, D3to CP (th) . 0.9 ns Minimum setup time, Pnto CP (ts) 1.7 ns Minimum hold time, Pnto CP (th) 1.0 ns Minimum s
15、etup time, D0/ CET to CP (ts) 1.8 ns Minimum hold time, D0/ CET CP (th) 0.7 ns Minimum setup time, CEP to CP (ts) . 1.8 ns Minimum hold time, CEP CP (th) . 0.6 ns Minimum setup time, Snto CP (ts) 3.3 ns Minimum hold time, Snto CP (th) 0.0 ns Minimum setup time, MR to CP (ts) 2.6 ns Minimum pulse wid
16、th, CP (tw) . 1.6 ns Minimum pulse width, MR (tw) 2.0 ns Maximum clock frequency, CP (fMAX) . 325 MHz 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unle
17、ss otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits.
18、MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or net
19、working permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92306 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 4 DSCC FORM 2234 APR 97 DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 -
20、 Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the even
21、t of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individ
22、ual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual
23、item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein
24、 for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Function select and trut
25、h tables. The function select and truth tables shall be as specified on figure 3. 3.2.4 Test circuits and switching waveforms. The test circuits and switching waveforms shall be as specified on figure 4. 3.3 Electrical performance characteristics and post-irradiation parameter limits. Unless otherwi
26、se specified herein, the electrical performance characteristics and post-irradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in tab
27、le II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the
28、manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appen
29、dix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and
30、V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply
31、 in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M,
32、 the requirements of MIL-PRF-38535, appendix A and herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92306 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 5 DSCC FORM 223
33、4 APR 97 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M.
34、For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain
35、the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit
36、group number 33 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92306 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 6 DSCC FORM 2234 APR 97 T
37、ABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TC +125C -5.7 V VEE -4.2 V Group A subgroups Device type Limits Unit unless otherwise specified Min Max High level output voltage VOHVEE= -4.2 V, 1, 2 All -1.025 -0.870 V VIH= -0.870 V, 3 -1.085 -0.870 Low level output vo
38、ltage VOLVIL= -1.830 V 1, 2 All -1.830 -1.620 V 3 -1.830 -1.555 High level threshold VOHCVEE= -4.2 V, 1, 2 All -1.035 V output voltage VIH= -1.165 V, 3 -1.085 Low level threshold VOLCVIL= -1.475 V 1, 2 All -1.610 V output voltage 3 -1.555 High level input current IIHVEE= -5.7 V, 1, 2 All 240 A VIN=
39、-0.870 V 3 340 Low level input current IILVEE= -4.2 V, VIN= -1.830 V 1, 2, 3 All 0.5 A Power supply drain current IEEVEE= -5.7, -4.2 V, Inputs open 1, 2, 3 All -195 -70 mA VEE= -4.8, -4.2 V, Inputs open -185 -70 Functional tests VEE= -5.7 V, -4.2 V, VIL= -1.652 V, VIH= -1.018 V, See 4.4.1b 7, 8 All
40、Propagation delay time, tPLH1, See figure 4 9 All 0.4 2.2 ns CP to Qn, QntPHL110 0.4 2.5 11 0.4 2.3 Propagation delay time, tPLH2, 9 All 1.7 3.8 ns CP to TC tPHL2 10 1.7 4.2 (shift mode) 11 1.3 3.9 Propagation delay time, tPLH3, 9 All 1.5 4.6 ns CP to TC tPHL3 10 1.6 5.2 (count mode) 11 1.2 4.6 See
41、footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92306 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical per
42、formance characteristics Continued. Test Symbol Conditions 1/ -55C TC +125C -5.7 V VEE -4.2 V Group A subgroups Device type Limits Unit unless otherwise specified Min Max Propagation delay time, tPLH4, See figure 4 9 All 0.8 2.8 ns MR to Qn, QntPHL410 0.9 3.2 11 0.6 2.9 Propagation delay time, tPLH5
43、, 9 All 2.7 5.2 ns MR to TC tPHL510 2.9 5.9 (count mode) 11 2.3 5.2 Propagation delay time, tPHL69 All 2.2 4.1 ns MR to TC 10 2.4 4.7 (shift mode) 11 2.1 4.3 Propagation delay time, tPLH7, 9 All 1.0 3.2 ns D0/ CET to TC tPHL710 1.3 4.1 11 0.7 3.2 Propagation delay time, tPLH8, 9 All 1.5 4.2 ns Snto
44、TC tPHL810 1.7 4.9 11 1.3 4.1 Transition time, tTLH, 9 All 0.2 1.8 ns Qn, Qn2/ tTHL10 0.2 2.0 11 0.2 1.9 1/ Each input/output, as applicable, shall be tested at the specified temperature for the specified limits. Output terminals shall be terminated through 50 to -2 V. Input terminals not designated
45、 shall be high logic level or low logic level. 2/ This parameter is provided as design information only (not tested but guaranteed). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92306 DEFENSE SUPPLY CENTER
46、 COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 8 DSCC FORM 2234 APR 97 Case Y Millimeters Inches Dimension Min Max Min Max Notes A 2.16 .085 b 0.41 0.46 .016 .018 c 0.10 0.15 .004 .006 D 22.10 28.45 .870 1.120 D1 9.40 10.16 .370 .400 4 E 22.10 28.45 .870 1.120 E1 9.40 10.16 .370 .400 4 e
47、 1.14 1.40 .045 .055 L 6.35 9.14 .250 .360 Q 0.89 1.27 .035 .050 5 S 1.91 .075 Notes: 1. The preferred unit of measurement is millimeters. However, this item was designed using inch-pound units of measurements. In case of problems involving conflicts between the metric and inch-pound units, the inch
48、-pound units shall rule. 2. Lead number 1 is identified by a tab located on the lead. 3. Lead numbers are shown for reference only and do not appear on package. 4. Dimensions D1 and E1 allow for glass meniscus. 5. Dimension Q shall be measured at the point of exit of the lead from the body. FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92306 DEFENSE SUPPLY CENTER COLUMBUS CO
