1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add device type 02 and LCC. Editorial changes throughout. 93-11-15 M. A. Frye B Changes in accordance with N.O.R. 5962-R288-94. 94-10-06 M. A. Frye C Make change to logic input high voltage test as specified in table I. Redrawn. - ro 99-12-06 R.
2、Monnin D Make change to logic input high current and logic input low current tests as specified in table I. - ro 01-04-20 R. Monnin E Add device types 03 and 04. - ro 01-05-03 R. Monnin F Redraw. Update drawing to current requirements. -.drw 12-02-28 Charles F. Saffle REV SHEET REV SHEET REV STATUS
3、REV F F F F F F F F F F F OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY Rick C. Officer DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT O
4、F DEFENSE CHECKED BY Sandra B. Rooney APPROVED BY Michael A. Frye MICROCIRCUIT, LINEAR, A/D CONVERTER, 12-BIT, MONOLITHIC SILICON DRAWING APPROVAL DATE 93-02-11 AMSC N/A REVISION LEVEL F SIZE A CAGE CODE 67268 5962-93060 SHEET 1 OF 11 DSCC FORM 2233 APR 97 5962-E116-12 Provided by IHSNot for ResaleN
5、o reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93060 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting
6、of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2
7、 PIN. The PIN is as shown in the following example: 5962 - 93060 01 M X A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator Case outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q a
8、nd V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.
9、 1.2.2 Device types. The device types identify the circuit function as follows: Device type Generic number Circuit function Operating temperature 01 AD872ASD 12-bit, 10 MSPS A/D converter -55C to +125C 02 AD872ASE 12-bit, 10 MSPS A/D converter -55C to +125C 03 AD872ASD 12-bit, 10 MSPS A/D converter
10、-40C to +125C 04 AD872ASE 12-bit, 10 MSPS A/D converter -40C to +125C 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for M
11、IL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outlines. The case outlines are as designated in MIL-STD-1835 as follows: Outline letter Descriptive designator Terminals Package
12、style X GDIP1-T28 or CDIP2-T28 28 Dual-in-line Y CQCC1-N44 44 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permit
13、ted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93060 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ AVDDrange with respect to AGND -0.5 V to 6.5 V AVSSrange with respect to AGND -6.5 V to 0.5
14、 V DVDDrange with respect to DGND -0.5 V to 6.5 V AGND range with respect to DGND . -1.0 V to 1.0 V AVDDrange with respect to DVDD. -6.5 V to 6.5 V Clock input range, OEN with respect to DGND -0.5 V to DVDD+ 0.5 V Digital outputs range with respect to DGND. -0.5 V to DVDD+ 0.3 V VINA, VINB, REF IN r
15、ange with respect to AGND -6.5 V to 6.5 V REF IN range with respect to AVDD. AVSSto 0 V REF IN range with respect to AVSS. 0 V to AVDDPower dissipation (PD) . 1.3 W Junction temperature . +150C Storage temperature range -65C to +150C Lead temperature (10 seconds) . +300C Thermal resistance, junction
16、-to-case (JC) See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA): Case outline X 60C/W Case outline Y 70C/W 1.4 Recommended operating conditions. Operating ambient temperature range (TA): Device types 01 and 02 . -55C to +125C Device types 03 and 04 . -40C to +125C 2. APPLICABLE DOCUMENTS
17、 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE
18、SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of
19、Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of prece
20、dence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. _ 1/ Stresses above the absolute
21、 maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93060 DLA LAN
22、D AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 as specified herein, or as modified in the device manufacturers Quality
23、 Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, con
24、struction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 here
25、in. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as speci
26、fied in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked wit
27、h the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RH
28、A designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“
29、or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the
30、 requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior
31、to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A c
32、ertificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land
33、 and Maritime -VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity
34、 retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in micro
35、circuit group number 93 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93060 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 5 DSCC FORM 2234 APR 97 TA
36、BLE I. Electrical performance characteristics. Test Symbol Conditions 1/ unless otherwise specified Group A subgroups Device type Limits 2/ Unit Min Max Resolution RES 1, 2, 3 All 12 Bits Differential 3/ nonlinearity DNL All codes histograms 1, 2, 3 All 12 Bits Zero error BPOETA= +25C 1 All 0.75 %FS
37、R Gain error ABTA= +25C 1 All 1.25 %FSR Zero error drift TCBPOEExternal 2.5 V reference TA+125C, -55C 2, 3 01, 02 0.30 %FSR External 2.5 V reference TA+125C, -40C 03, 04 0.30 Gain error drift TCAINTInternal 2.5 V reference TA= +125C, -55C 2, 3 01, 02 1.75 %FSR Internal 2.5 V reference TA= +125C, -40
38、C 03, 04 1.75 TCAEXTExternal 2.5 V reference TA= +125C, -55C 01, 02 0.5 External 2.5 V reference TA= +125C, -40C 03, 04 0.5 Power supply rejection ratio PSRR 4/ 1, 2, 3 All 0.125 %FSR Analog input range VIN1, 2, 3 All 1 V Internal reference output voltage VREF1, 2, 3 All 2.46 2.54 V Power dissipatio
39、n PD1, 2, 3 All 1.3 W Power supply current IAVDD1, 2, 3 All 92 mA IAVSS1, 2, 3 All 150 IDVDD1, 2, 3 All 21 IDRVDD1, 2, 3 02, 04 2 Signal-to-noise and distortion ratio S/(N+D) fIN= 1 MHz, fS= 10 MHz 1, 2, 3 01, 03 61 dB 02, 04 60 Total harmonic distortion THD fIN= 1 MHz, fS= 10 MHz 1, 2, 3 01, 03 -62
40、 dB 02, 04 -60 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93060 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Elec
41、trical performance characteristics continued. Test Symbol Conditions 1/ unless otherwise specified Group A subgroups Device type Limits 2/ Unit Min Max Logic input high voltage (CLK) VIH1, 2, 3 All 2.0 V Logic input high voltage (OEN) VIH1, 2, 3 02, 04 3.5 V Logic input low voltage VIL1, 2, 3 All 0.
42、8 V Logic input high current (CLK) IIHVCLK= 5.0 V 1, 2, 3 All 115 A Logic input low current (CLK) IILVCLK= 0 V 1, 2, 3 All 115 A Logic output high voltage (MSB-Bit 12, OTR) VOHIOH= 5.0 mA 1, 2, 3 All 2.4 V Logic output low voltage (MSB-Bit 12, OTR) VOLIOL= 1.6 mA 1, 2, 3 All 0.4 V Clock period tCSee
43、 figure 2, duty cycle = 50 percent 9, 10, 11 All 100 ns Output delay tODSee figure 2 9, 10, 11 All 10 ns Leakage current IZThree-state 1, 2, 3 02, 04 10 A 1/ Unless otherwise specified, AVDD= +5V, DVDD= +5 V, AVSS= -5 V, and fSAMPLE= 10 MHz. For device types 01 and 02, -55C TA +125C. For device type
44、s 03 and 04, -40C TA +125C 2/ The limiting terms “min” (minimum) and “max” (maximum) shall be considered to apply to magnitudes only. Negative current shall be defined as conventional current flow out of a device terminal. 3/ Minimum resolution for which “no missing codes” is guaranteed. 4/ Test con
45、ditions, AVDD= 5.00 0.25 V, AVSS= 5.00 0.25 V, and DVDD= 5.00 0.25 V. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93060 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 7 DSCC FORM 2
46、234 APR 97 Device types 01, 03 02, 04 Case outlines X Y Terminal number Terminal symbol 1 VINAVINA2 VINBVINB3 AVSSNC 4 AVDDNC 5 AGND AVSS6 DGND AVDD7 DVDDNC 8 BIT 12 (LSB) NC 9 BIT 11 AGND 10 BIT 10 DGND 11 BIT 9 DRGND 12 BIT 8 DRVDD13 BIT 7 OEN 14 BIT 6 NC 15 BIT 5 NC 16 BIT 4 BIT 12 (LSB) 17 BIT 3
47、 BIT 11 18 BIT 2 BIT 10 19 BIT 1 ( MSB ) BIT 9 20 OTR BIT 8 21 CLK BIT 7 22 DVDDBIT 6 23 DGND BIT 5 24 AGND BIT 4 25 AVSSBIT 3 26 REF OUT BIT 2 27 REF GND BIT 1 (MSB) 28 REF IN NC 29 - MSB 30 - OTR 31 - CLK 32 - DRVDD33 - DVDD34 - DRGND 35 - NC 36 - AGND 37 - NC 38 - AVDD39 - NC 40 - AVSS41 - REF OU
48、T 42 - REF GND 43 - REF IN 44 - NC FIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93060 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 8 DSCC FORM 2234 APR 97 FIGURE 2. Timing diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDAR
